Kdrs505x Parts

This side panel assembly replaces a damaged or bent outer side wall to restore the appliance's exterior fit and finish. It provides a stable mounting surface and helps protect internal components from dust and damage. What it does:

• Replaces a cracked, dented, or rusted side panel to improve appearance and structural support
• Restores proper alignment for doors, controls, or adjacent panels
• Helps keep internal parts and wiring protected from debris and moisture
• Can reduce rattles or vibration caused by a loose or warped side panel

• One complete side panel assembly as shown

• Installation requires removing screws and possibly adjacent trim; keep hardware organized for reassembly
• Power off and disconnect the appliance before starting any repair
• Handle edges carefully — panel edges may be sharp
• If mounting holes don't align, do not force; verify panel orientation and hardware match your appliance

Replacement grate kit for gas cooktops that restores a stable, level cooking surface and improves cookware support. Ideal for replacing cracked, chipped or worn grates so pots and pans sit securely over the burner. What it does:

• Replaces damaged or worn cooktop grates that can cause cookware to wobble
• Restores a flat, stable surface for even cookware contact and safer cooking
• Helps eliminate rattling or shifting grates that interfere with burner use
• Allows burners and cookware to align properly for consistent heat transfer

• Turn off the cooktop and allow all parts to cool completely before handling.
• Wear gloves to protect your hands from sharp edges; handle grates carefully.
• Ensure burners and caps are properly seated after installing the grates; test each burner for correct ignition.

This upper door insulation restores the door's thermal barrier to help the refrigerator/freezer hold temperature and reduce condensation. It replaces deteriorated or missing insulation to improve cold-air retention and reduce frost build-up. What it does:

• Replaces worn or damaged insulation inside the upper door cavity
• Helps limit heat transfer to maintain interior temperature
• Reduces condensation and frost forming on the door liner
• Can address symptoms like uneven cooling, warm spots near the door, or excessive frost

• Disconnect power to the appliance before starting any service
• Access requires removing the inner door liner or trim—keep screws and clips organized for reassembly
• Position insulation without compressing; use the original retainer clips or adhesive as OEM specified
• Dispose of old insulation per local regulations and check door seal condition after reinstall

This Holder ORF is a small mounting retainer used to secure internal components so parts stay aligned and stable during normal appliance operation. Replacing a damaged or missing holder prevents loose parts and rattling. What it does:

• Secures and positions a specific internal component or assembly
• Keeps parts aligned to prevent rubbing, vibration, or noise
• Restores proper fit where the original retainer is cracked, bent, or missing
• Helps maintain reliable operation by holding components in place

• Disconnect power (and gas, if applicable) before servicing the appliance
• Inspect adjacent parts and fasteners for wear; replace any damaged hardware
• Use basic hand tools; avoid over-tightening which can crack the retainer

This orifice spud is the small gas jet used in LP conversion kits to regulate propane flow to a burner, helping restore correct flame size and combustion after converting to liquid propane. It's a direct-fit component for affected burners. What it does:

• Replaces the burner jet that meters propane for safe, consistent flame
• Restores proper flame height and prevents oversized or sooting flames after LP conversion
• Helps burners light reliably and maintain even heat
• Works as part of an approved LP conversion to match appliance fuel type

• Turn off gas supply and power before starting any gas appliance service
• Use the correct orifice size and follow the appliance LP conversion instructions or service manual
• Hand-tighten and then torque per manufacturer spec if provided; avoid overtightening

This is an oven rack that is made for use on an range. The oven rack is inserted into the oven and there is likely more than one per unit. It creates a stable place to place ovenware for baking inside of the oven. They function similarly to shelves.If the oven rack begins to rust, it will need to be replaced. These can also sustain damage if they experience forceful impact with a heavy object. Over time, they may deteriorate and need to be replaced. Some people may wish to wear work gloves to protect their hands during the replacement process as these can become very dirty. It is essential to let the original oven rack cool completely before removing it from the oven for replacement. This part is sold individually and is sourced straight from the manufacturer. This particular oven rack is compatible with ranges that are manufactured by the KitchenAid and Maytag brands.