Kenmore 7964158 Parts

The Spider Arm is an OEM part for LG washing machines. As an important component linking internal mechanics, the spider arm connects the basket or tub to other components like the drive motor. It facilitates the spinning motion essential for washing cycles while also enabling water to properly agitate clothing. 

Symptoms of a bad spider arm include:

• The tub not spinning or spinning unevenly
• Vibration or noise issues arising from the center of the machine  
• Water not draining or agitating clothes as intended
•  premature wear on other connected parts over time

Causes of a bad spider arm can be regular use over several years, damage from excessively heavy loads, or impact from an object inside the tub. Not replacing a faulty spider arm can accelerate damage to other expensive parts. 

This LG replacement part is also compatible with Sears/Kenmore models. 

This washer drum lifter (baffle) mounts inside the drum to raise and tumble clothes as the basket turns. Replace a cracked or missing lifter to restore wash action, help protect fabrics, and reduce rattling noises.

• Attaches to the inner drum and lifts garments during rotation for effective tumbling
• Helps distribute loads and improve mechanical cleaning action
• Direct replacement for lifters that are cracked, loose, sharp-edged, or missing
• Typical symptoms: poor tumbling/wash results, thumping or rattling from the drum, clothing snags or tears, lifter wobbling or fallen off

• Disconnect power and turn off water supply before servicing
• Open the door and rotate the drum to access the lifter
• Depending on model, release locking tabs from inside the drum or remove the retaining fastener; align and secure the new lifter
• Ensure the lifter is fully seated and secure; run a short rinse/spin to verify proper operation

This clamp assembly secures a hose or tubing connection to maintain a watertight seal and reduce vibration. Replacing a worn or damaged clamp helps stop leaks and prevents hoses from slipping loose during operation. What it does:

• Holds a hose or tube firmly in place to maintain proper sealing at the connection point.
• Prevents leaks caused by loose, cracked or corroded clamps.
• Reduces vibration and rattling from unsecured hoses.
• Common symptom: visible leaking, water pooling, or a loose hose connection.

• Disconnect power and shut off water supply before starting any repair.
• Use the correct pliers or screwdriver for the clamp type; avoid damaging the hose.
• Inspect the mating hose and seal; replace any cracked or hardened hoses before reinstalling.
• Do not overtighten—tighten just enough to secure the hose without cutting or deforming it.

This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:

• Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
• Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
• Reduces vibration-related noise caused by loose hoses or wires
• Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues

• One clamp

• Disconnect power to the appliance before servicing; shut off water supply if working with water lines
• Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
• Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
• If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware

A replacement balance weight that helps stabilize the washer drum during spin cycles to reduce vibration and noise. Restores proper weight distribution so the washer runs more quietly and reliably. What it does:

• Counters drum imbalance to reduce shaking and excessive movement during spins
• Helps minimize noise caused by uneven loads
• Preserves drivetrain components by reducing stress from heavy vibration
• Supports consistent spin performance and load stability

• Disconnect power and water supply before starting any repairs
• Handle carefully—weights can be heavy and require a helper or proper lifting technique
• Follow the washer's service manual for mounting location, orientation, and fastener torque
• After installation, run a test spin with a small load to reduce vibration

This connector hose replaces the appliance's water connection to restore secure water flow and reduce the risk of leaks or interrupted dispenser/ice-maker operation. It's a direct replacement for a damaged or leaking supply connector. What it does:

• Connects the household water supply to the appliance's internal water valve or dispenser.
• Restores reliable water flow when a cracked, split, or collapsed hose prevents proper delivery.
• Reduces water leakage caused by worn or damaged connector ends and seals.
• Commonly needed when you see visible leaks, no water to the dispenser/ice maker, or a loose/broken hose connection.

• Turn off water supply and unplug the appliance before replacing the hose to avoid electric shock or water damage.
• Use proper clamps and fittings; make sure connections are seated and tightened just enough to stop leaks—do not overtighten.
• After installation, restore power and water, then check all connections carefully for leaks. Replace immediately if the hose or fittings show signs of damage.

This multi wiring harness connects control circuitry to multiple components, restoring reliable electrical pathways for proper operation. It replaces a damaged or frayed harness to help eliminate intermittent power, unresponsive controls, or component failures caused by wiring faults. What it does

• Routes power and signals between the control board and several appliance components.
• Re-establishes secure electrical connections when original wires are broken, burnt, or corroded.
• Can address symptoms such as intermittent operation, components not receiving power, or erratic behavior tied to wiring faults.
• Uses OEM-style connectors and wiring lengths to match factory routing for a proper fit.

• One multi wiring harness as shown

• Always disconnect power (unplug or shut off breaker) before servicing the appliance.
• Handle connectors by the housings—do not pull on wires—and ensure all plugs fully seat with audible clicks.
• Route the harness following original wire paths and secure with existing clips or ties to prevent contact with moving or hot parts.

A replacement hose clamp that secures a flexible hose to its fitting to help prevent leaks and disconnections. Restores a tight, reliable seal so hoses stay seated during normal use. What it does:

• Holds a rubber or plastic hose firmly to a pump, valve or connection to prevent leaks.
• Helps stop hose pull-off that can cause water leaks or appliance interruptions.
• Commonly replaced when clamps are corroded, bent, cracked or missing.
• Works as a low-cost repair to restore a secure hose connection without replacing the hose assembly.

• Disconnect power to the appliance and shut off the water supply before servicing.
• Use the correct tool (slip-joint pliers for spring-style clamps or a screwdriver for screw-type clamps) and avoid pinching the hose.
• Inspect the hose and fitting for damage; replace the hose if it's cracked or excessively worn.
• After installing, restore power/water and run a short test cycle or check for leaks.

The Power Cord Assembly is an OEM replacement part for LG front-loading washing machines. As the primary connection to household electricity, this cord safely delivers the required voltages to internal components.

Causes of a damaged or defective cord typically involve accidental cuts, abrasions or punctures accumulated over time. Repeated bending stresses during installations can prematurely crack insulation as well.

Symptoms of a problematic power cord include: 

• Inability to power "On" when plugged in  
• Tripped breakers or ground fault outlets
• Visible wire fraying or other signs of compromised integrity

This OEM assembly fits some Kenmore/Sears machines and protects against potential shock or fire hazards.

This hinge spring restores proper door tension so the appliance door opens and closes smoothly and stays in position. Replacing a worn spring reduces sagging, uneven closing, and noisy or slamming doors. What it does:

• Provides tension at the hinge to hold door position and improve alignment
• Helps prevent door sagging and uneven gaps caused by worn springs
• Reduces slamming, popping, or grinding sounds during door movement
• Common symptom: door won't stay open/closed or feels loose at the hinge

• Disconnect power and unplug the appliance before starting any repair
• Support the door while removing/installing the spring to prevent it from dropping
• Basic hand tools (screwdriver, pliers) are typically needed; follow the appliance's service guide

This dispenser assembly replaces the door-mounted housing that routes water and ice to the refrigerator dispenser, restoring reliable dispensing and preventing leaks. Fits as the original-style door dispenser component. What it does:

• Channels water and ice from the door to the dispenser chute for normal dispensing operation
• Seals dispenser openings to help prevent leaks and drips at the door
• Supports the dispenser actuator and user controls (where applicable)
• Helps restore proper alignment and smooth dispensing if door components are loose or damaged

• Disconnect power and water supply before starting work to avoid electrical shock and flooding
• Replace through the refrigerator door panel; some models require removing the inner door liner and control components
• Handle with care to avoid damaging tabs and mounting clips; verify all seals and gaskets seat correctly

A molded water guide that routes dispenser water inside the refrigerator to the dispenser/ice area, helping direct flow and reduce splashing. Fits the factory mounting points for a clean, secure path for water. What it does

• Channels water from the inlet tubing toward the dispenser/ice assembly to prevent misdirected flow.
• Helps keep water from pooling or dripping inside the cabinet or on internal components.
• Common replacement when you see water on shelves, puddling near the dispenser, or reduced or misdirected dispenser flow.
• Preserves proper alignment of the dispenser plumbing to prevent kinks or strain on tubing.

• One water guide (single molded channel) as shown.

• Turn off the refrigerator and shut off the water supply before starting; disconnect power for safety.
• Remove interior panels or shelves as needed to access mounting points; keep fasteners for reassembly.
• Inspect adjoining tubing and seals for damage and replace any worn components to ensure a leak-free fit.
• After installation, restore power and water, then check carefully for leaks during an initial test dispense.

This protective cover shields internal components and wiring from dirt, moisture and accidental contact, helping keep the appliance safe and functioning properly. It's a small replacement panel that restores the appliance's factory protection. What it does:

• Covers and protects internal parts and wiring from debris and accidental impact
• Prevents loose components from rattling or shifting during operation
• Helps maintain proper spacing and alignment of nearby panels and clips
• Addresses symptoms like visible damage, missing cover, exposed wiring, or unusual noise from loose trim

• Disconnect power before starting any repair to avoid shock or injury
• Typically secures with clips or a few screws; use basic hand tools and take care not to strip fasteners
• Inspect mounting tabs and surrounding trim for damage; replace any broken clips before reassembly

This clamp assembly secures a hose or component to its mounting point to help prevent leaks and reduce vibration. It replaces a worn or broken clamp so the connection stays tight and stable. What it does:

• Secures hoses, lines, or parts to their mounting points to maintain a sealed connection
• Helps reduce vibration and movement that can cause wear or noise
• Restores proper fit where a cracked, bent, or missing clamp allows leaks or misalignment
• Simple, direct replacement—matches the OEM attachment function

• Disconnect power and water before servicing to avoid shock or flooding
• Inspect mating surfaces and hose condition; replace hose if damaged before installing clamp
• Use pliers or a screwdriver as needed; tighten to a snug fit—do not over-tighten
• Follow the appliance's service manual for disassembly/reassembly guidance and safety

This small replacement hole cap covers unused access openings to restore a finished appearance and help keep out dust and debris. It's a simple, low-cost part that maintains appliance appearance and helps prevent contamination. What it does:

• Covers an open service or mounting hole to improve cosmetics
• Blocks dust, lint and small debris from entering the cabinet or enclosure
• Helps reduce drafts around service openings
• Prevents accidental contact with exposed fasteners or edges

• No special tools required; typically snaps or presses into place
• Secure fit before use
• If removing nearby panels, unplug the appliance or disconnect power first
• Replace any damaged retaining features before relying on the cap for protection