Kfis525xvms9 Parts

This refrigerator water tube carries fresh water between the valve, filter/reservoir, and the dispenser or ice maker. Replacing a damaged or kinked tube helps restore safe, leak-free water flow and consistent dispensing/ice production.

• Routes water between internal components such as the inlet valve, filter/reservoir, and dispenser/ice maker assemblies
• Typical failure signs: leaks under/behind the refrigerator, slow or no water at the dispenser, reduced or no ice
• Physical damage like cracks, pinholes, or kinks indicates the tube should be replaced
• Proper routing prevents sharp bends that can restrict flow or cause future leaks

• Unplug the refrigerator and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Note original routing; cut tube ends square and fully seat into quick-connect fittings, then tug gently to confirm engagement
• Restore water and power, then check all connections for leaks

This thermostat regulates appliance temperature to help maintain proper heating and cycling for safe, consistent operation. It replaces a failed thermostat to restore correct temperature control and reduce unexpected shutoffs or inconsistent heat. What it does:

• Senses and opens/closes the circuit to control heating elements or compressors
• Can stop heating when the set temperature is reached to prevent overheating
• Commonly used when the appliance won't reach or maintain the correct temperature
• Helps address intermittent heating, continuous running, or overheating symptoms

• Disconnect power before servicing to avoid shock or injury
• Handle thermostat terminals carefully; ensure secure, correct wiring connections

Replacement mounting bracket that secures a panel or internal assembly to the appliance so parts stay aligned and stable. Installs in minutes to stop rattling, reduce movement and restore a proper fit. What it does:

• Provides a secure mounting point for a panel, trim or internal component
• Keeps assemblies aligned to prevent gaps, rubbing or binding
• Stops rattling and vibration caused by a loose or damaged bracket
• Replaces bent, cracked or corroded brackets that no longer hold parts firmly

• Disconnect power (and water if applicable) before beginning any repair
• Retain original fasteners; replace damaged screws or clips as needed
• Hand-tighten fasteners first, then torque to manufacturer specs if available

This left-side slide bracket secures and guides a sliding assembly so drawers or components open smoothly and stay aligned. It replaces a worn or broken bracket to restore proper support and reduce binding or sagging. What it does:

• Provides structural support for the left side of a sliding drawer/assembly
• Keeps slides aligned so the drawer opens and closes smoothly
• Helps stop sagging, catching, or uneven movement of the sliding part
• Replaces cracked, bent, or damaged brackets that interfere with operation

• Disconnect power and/or unplug the appliance before starting any repair
• Remove any outer panels or drawer components as needed to access the bracket
• Keep original fasteners; install bracket in the same orientation and tighten screws securely but do not overtighten
• If movement still feels restricted after replacement, check mating slide components and alignment

This left door bushing supports a refrigerator/freezer door hinge for smooth, stable operation and helps prevent wear and noise. It restores proper door movement and alignment when the original bushing is worn or damaged. What it does:

• Guides and cushions the door hinge to reduce friction and wear
• Helps stop door binding, sticking, or misalignment
• Reduces squeaks and rattles from a loose or worn hinge area
• Maintains consistent door pivot for reliable opening and closing

• Disconnect power to the appliance before attempting any repair.
• Access may require removing the door or hinge trim; follow manufacturer instructions.
• Inspect hinge and surrounding parts for wear; replace any damaged hardware for best results.

A molded defrost drain funnel that routes condensation and melted frost into the refrigerator's drain to help prevent pooling and interior leaks. Replaces cracked or clogged funnels to restore proper water flow in the drain path. What it does

• Guides defrost and condensation water from the evaporator area into the fridge drain system.
• Helps prevent water pooling inside the fresh-food or freezer compartments.
• Worn, cracked or clogged funnels can cause dripping, pooling or frost build-up near the evaporator.
• Restores a secure, directed path for meltwater to reach the drain tube and pan.

• Disconnect power to the appliance before accessing internal components to reduce shock risk.
• Remove food and any removable shelving to access the evaporator/drain area; handle plastic trim carefully to avoid breakage.
• Inspect surrounding drain area for ice, debris or clogs and clear before reinstalling the funnel.
• If clips or screws secure the funnel, retain hardware and reinstall securely; test a small amount of water to ensure proper drainage.

This replacement shelf trim restores the finished front edge of a refrigerator shelf, helping keep small items from sliding off and improving the shelf's appearance. It's the correct cosmetic/edge piece for a damaged, cracked, or missing shelf front. What it does:

• Attaches to the front edge of a refrigerator shelf to provide a finished trim and edge protection
• Helps prevent small items from sliding off the shelf front
• Replaces cracked, chipped, or broken shelf edging that affects appearance or function
• Matches the original shelf front location and mounting style

• One shelf trim

• Remove the shelf and place on a soft, stable surface before installing the trim
• Trim typically snaps onto the shelf front; press evenly until clips engage
• Handle glass shelves with care to avoid breakage; wear gloves and eye protection as needed
• If clips are damaged or installation feels forced, review the shelf and clip condition.

This wire harness routes power and signals between your appliance's control and components to restore reliable electrical connections. Replacing a damaged harness helps stop intermittent power, faulty controls, or non-starting appliances. What it does:

• Transfers power and control signals between main control, motor, and other components
• Replaces cracked, burned, or frayed wiring that can cause intermittent operation
• Helps resolve symptoms like appliance not starting, control lights flickering, or components losing power
• Restores secure connector fit where pins or terminals are loose or corroded

• Disconnect all power before beginning service to avoid shock or injury
• Take photos or label connectors before removing the old harness to ensure correct routing
• Inspect connectors and terminals for damage; replace harness if insulation or terminals are compromised
• Secure harness away from sharp edges, moving parts, and heat sources during reassembly

This pantry brace secures the pantry assembly on 36-inch refrigerator pantry units, restoring proper alignment and stability for smooth door operation. It replaces a bent or broken brace to help maintain correct pantry support and fit. What it does:

• Provides structural support for the pantry/pull-out assembly to prevent sagging or misalignment
• Helps restore smooth opening and closing when the pantry feels loose or uneven
• Replaces damaged or cracked braces that can cause rattling or binding
• Works as a direct-fit replacement for the 36-inch pantry brace used in compatible Whirlpool pantry assemblies

• One pantry brace

• Remove power to the appliance and empty the pantry/pull-out before replacing the brace
• Use appropriate hand tools and avoid overtightening fasteners to prevent damage
• Inspect surrounding hardware and tracks for wear while replacing the brace

This cover corner replaces a missing or damaged corner trim piece to restore the refrigerator's interior/exterior finish and help keep shelves and bins seated properly. It provides a clean, finished look and protects edges from wear. What it does:

• Replaces the corner trim/filler that covers panel edges or joins interior liners
• Helps keep adjoining panels, shelves or bins aligned and reduces gaps
• Restores appearance after chipping, cracks or impact damage

• Designed for drop-in or snap-on installation; verify fit against the appliance before final assembly
• Use basic hand tools; avoid excessive force which can crack plastic parts
• Disconnect power if removing interior panels or working near electrical components

Upper freezer glide that supports and guides the freezer drawer for smooth opening and closing. Replaces a worn or damaged glide to help eliminate binding, scraping, and uneven drawer movement. What it does:

• Guides and supports the upper freezer drawer for smooth travel; a failed glide often causes the drawer to stick or catch.
• Reduces metal-on-metal contact and scraping noises when opening or closing the drawer.
• Helps restore proper drawer alignment to prevent uneven gaps or rubbing against the cabinet.
• Lowers stress on adjacent components by returning consistent, even drawer movement.

• Disconnect power to the appliance before beginning any service work.
• Remove freezer contents and the drawer assembly per the manufacturer's instructions to access the glide.
• Replace the glide following the OEM diagram/steps; keep fasteners and mounting points aligned during reassembly.
• Test drawer operation after installation and adjust as needed for smooth, even travel.

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

This replacement ejector is the plastic arm that pushes harvested ice cubes out of the ice mold and into the storage bin, helping restore proper ice ejection and reduce ice that sticks inside the tray. What it does:

• Pushes ice cubes out of the ice mold during the ice maker's harvest cycle.
• Works with the ice maker's motor/gear assembly to advance cubes into the bin.
• Replaces worn, cracked, or broken ejector arms that can leave ice stuck in the mold.
• Can help address symptoms such as cubes that don't eject, partial fills, or frequent ice jams.

• Disconnect power to the refrigerator before servicing to prevent electrical shock.
• Remove the ice bin and follow the OEM ice maker removal steps to access the ejector.
• Handle plastic components carefully to avoid cracking; inspect gears, mounts, and the ice tray for related wear.

This temperature control bar is the actuator used to adjust and regulate the appliance's internal temperature, restoring proper temperature response for the bar/beverage control system. It provides a direct replacement for the OEM control bar assembly. What it does:

• Transfers user temperature adjustments to the control mechanism so the appliance reaches the set temperature
• Restores correct temperature changes when the control knob or selector fails to respond
• Helps address symptoms like incorrect temperature readings, temperature not changing, or unstable cooling behavior
• Works with the existing control housing and selector components to re-establish normal operation

• One temperature control bar

• Disconnect power before servicing to avoid electric shock
• Handle the part and surrounding components carefully to avoid damaging clips or wiring
• You may need to remove interior panels or the control housing to access the part;
• Verify the part number on your existing component before installation