Kgss903sss Parts

This orifice holder serves the gas surface burner position designated TCB. It directs gas from the valve to the burner and provides a stable mount for the igniter and burner head to maintain reliable ignition and flame performance.

• Routes gas from the manifold/valve through the orifice to the burner head
• Supports proper alignment of the burner head and cap
• Provides mounting point for the surface igniter/electrode
• Failure symptoms include a burner that won't light or is slow to ignite, weak or uneven flame, or igniter clicking without ignition on that burner

• Disconnect power and shut off the gas supply before servicing
• Allow the cooktop/range to cool completely
• Remove burner cap and head; lift top as required. Transfer the brass orifice and igniter/electrode from the old holder if applicable, then install the new holder
• Reassemble, restore gas/power, and check all connections for leaks with a soap solution. Verify proper ignition and flame

This replacement screw secures appliance components and panels. Replacing worn or missing hardware restores a tight, rattle-free fit and helps keep assemblies properly aligned for reliable performance.

• Fastens panels, brackets, or covers to the appliance frame or mating parts
• Helps maintain proper alignment and reduces vibration and noise
• Replaces missing, stripped, or corroded screws
• Common signs to replace: loose or rattling panels, misaligned parts, damaged screw head or threads

• Disconnect power; also shut off water or gas to the appliance if applicable
• Compare to the original to ensure thread and length match before installing
• Start threads by hand to avoid cross-threading; tighten only until snug
• If the mating clip/insert is stripped, replace that hardware as well

This fixed high-limit thermostat is a safety device for your oven. It monitors temperature and opens the circuit if the cavity overheats, helping protect components and restore normal heating when the failed thermostat is replaced.

• Provides over-temperature protection for the oven's heating circuit
• Opens the electrical circuit at a preset limit to stop heat when overheating occurs
• Typical symptoms of failure: oven won't heat, shuts off during use, or won't start after a self-clean cycle
• Often tests open for continuity at room temperature when failed

• Disconnect power at the breaker before servicing; oven circuits carry dangerous voltage
• Allow the appliance to cool completely before access
• Access location varies by model; the thermostat is typically mounted on or near the oven cavity or rear panel
• Move wires one at a time to the new thermostat, ensure tight spade connections, remount securely, restore power, and test

This control transformer reduces incoming line voltage to the low voltage required by the appliance's control circuit or lighting. Replacing a failed transformer restores proper power to the controls so the unit operates as designed. What it does:

• Steps down household line power to low voltage for control boards, relays, or lighting circuits
• Provides electrical isolation to help protect sensitive control components
• A failed transformer may leave the control/display dead or make low-voltage features (like lights) inoperative; may also blow a fuse

• Disconnect power at the breaker or unplug the appliance before servicing
• Use your model's wiring diagram; transfer wires one at a time to the matching terminals
• Mount securely in the original location; keep wires clear of sharp edges and heat sources
• If a fuse opened, inspect wiring and downstream loads for shorts before restoring power

This orifice holder secures the gas orifice in the G4 burner assembly so fuel flows correctly to the burner. It helps restore reliable ignition and a steady flame for safer, more consistent cooking. What it does:

• Holds the burner orifice in place to maintain correct fuel delivery to the burner.
• Helps correct ignition issues caused by a loose, misaligned, or damaged orifice holder.
• Promotes an even, stable flame and consistent heat across the burner.
• Used when burner flames are weak, uneven, or fail to light reliably.

• Turn off the appliance and shut off gas and electrical power before servicing. If you smell gas, stop.
• Remove burner grates and caps to access the orifice holder; reassemble components in original order.
• Inspect the orifice and threads for damage before installation; hand-tighten and avoid over-torquing.

This 10-24 threaded screw secures appliance components that use a #10 machine screw. It provides reliable fastening for panels, brackets, and assemblies so parts stay aligned and stable during normal use and service. What it does:

• Fastens panels, brackets, or assemblies that accept a 10-24 machine screw
• Maintains alignment and structural connection under normal operating loads
• Replaces worn, stripped, or missing screws to restore secure mounting
• Works with sheet-metal and component mating nuts or threaded inserts commonly used in appliances

• One 10-24 threaded screw

• Power tools can be used; avoid overtightening to prevent stripped threads or damaged components
• Disconnect power and follow all safety steps for your appliance before servicing
• Ensure proper engagement and torque to avoid damage

This screw secures panels, brackets, and internal components in your appliance, keeping assemblies tight and aligned. Replacing worn or missing hardware helps prevent vibration and rattling and restores a solid fit after service or everyday use.

• Fastens sheet-metal panels, brackets, and internal parts to the cabinet or frame
• Helps maintain alignment and reduce vibration or rattling noises
• Replaces missing, corroded, or stripped screws
• Supports safe, secure reassembly during repairs

• Disconnect power; for gas appliances, also shut off the gas supply before beginning
• Support parts being removed so components aren't stressed or misaligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Wear cut-resistant gloves when working around sharp metal edges

This internal triple crown burner head replaces the inner burner component that supports the burner cap and helps shape the flame for consistent cooking. It restores proper burner function when the inner head is damaged or warped. What it does:

• Directs gas flow to the burner ports to produce an even flame across the triple-C burner pattern
• Helps maintain stable flame for simmering and normal cooking heat
• Can resolve low, uneven, or fluctuating flame caused by a damaged or warped internal head
• Works with the matching burner cap and base to ensure correct flame distribution

• Disconnect power to the cooktop and shut off the gas supply before servicing
• Handle parts carefully to avoid bending ports or damaging mating surfaces
• Verify correct fit and orientation before reassembly; replace any other damaged burner components as needed

This wire harness connects the control/switch assembly to the appliance's thermal cutoff and control circuits, restoring reliable electrical connections for proper operation. It's a direct-fit replacement when the original wiring is damaged or corroded. What it does:

• Provides the factory routing and connectors between the control/switch and TCB/thermal cutoff
• Re-establishes lost or intermittent power caused by damaged wiring or broken terminals
• Helps stop failures that cause controls to be unresponsive or cycles to stop unexpectedly
• Uses OEM-style terminals and insulation to match original fit and function

• One wire harness (switch TCB) as shown

• Disconnect power before starting — verify the appliance is completely de-energized
• Take photos of existing wire routing and connector locations to ensure correct reassembly
• Plug connectors fully and secure the harness along original clips or tie points; avoid sharp edges
• If terminals are damaged at mating parts, inspect and replace those components rather than splicing connectors

This orifice spud meters gas to a range or cooktop burner for correct flame size and reliable ignition. Replacing a damaged or clogged spud restores consistent burner performance and safer operation. What it does:

• Controls gas flow to the burner for proper flame height and shape
• Helps ensure reliable ignition and steady, even heating
• Commonly used when flames are weak, uneven, or burners fail to light
• Prevents gas flow issues caused by damage, wear, or blockage

• One orifice spud

• Always shut off the gas supply and disconnect power before servicing gas appliances
• Use appropriate wrench size and take care not to overtighten; replace any damaged gaskets or fittings
• After installation, check all fittings for leaks with a soap solution or approved leak detector

This small burner valve controls gas flow to a single cooktop burner, restoring reliable ignition and flame control. Use when a burner won't light, has weak or uneven flame, or fails to respond to the control knob. What it does

• Regulates gas flow to the burner for proper ignition and flame adjustment
• Replaces a worn or leaking valve that can cause no flame or low/irregular flame
• Helps restore consistent heat output and safe burner operation
• Works with the range's control knob mechanism to open and close gas flow

• One small burner gas valve

• Disconnect power and shut off the household gas supply before servicing
• Only install on compatible appliances; follow OEM diagram and torque specs when available
• If you smell gas during testing or installation, stop.

This valve kit repairs the appliance's water/control valve assembly and provides the small mounting screw needed for secure installation. It replaces a worn or damaged valve kit so the appliance can restore proper valve function. What it does:

• Replaces the valve assembly components that control water flow or internal fluid routing
• Helps stop issues caused by a damaged valve kit, such as inconsistent water delivery or valve leakage
• Restores secure mounting with the included screw to prevent loose fittings
• Works as the direct replacement kit specified for the original valve location

• Disconnect power and shut off water supply before starting any repair
• Handle valve components carefully to avoid damaging seals and fittings
• Use basic hand tools; avoid overtightening the mounting screw to prevent stripping

This thermistor is the temperature sensor used by a warm drawer to monitor and regulate internal temperature, helping maintain consistent warming for cooked foods. Replaces a failed or out-of-range sensor to restore correct temperature feedback. What it does:

• Senses warm-drawer temperature and sends a resistance-based signal to the control board
• Allows the control system to maintain desired warming temperature
• Common symptom: warm drawer not holding correct temperature or displaying temperature-related error codes
• Safe, widely accepted fix when diagnostics indicate an open/short or out-of-spec thermistor

• One thermistor temperature sensor

• Disconnect power to the appliance before accessing internal components
• Handle the sensor and connector gently; avoid pulling on wires
• Route and secure the lead per the original routing to prevent pinching or heat exposure

This replacement burner head restores the proper flame shape and heat distribution on gas cooktops with a triple-crown external burner design. It helps improve ignition and even cooking across pots and pans. What it does

• Directs and shapes the gas flame for even heat across cookware.
• Replaces damaged, corroded, or warped burner head surfaces that cause uneven heating.
• Can resolve weak, irregular, or misdirected flames and intermittent ignition at the burner.
• Works as part of the burner assembly to maintain safe, consistent combustion.

• Turn off gas supply and electrical power to the appliance before servicing.
• Remove grates and burner cap, then lift off and replace the burner head; ensure proper alignment before reassembly.
• Inspect other burner components (cap, base, or orifice) for damage or debris that may affect performance.

Color: Stainless

This oven light assembly provides interior illumination so you can check cooking progress without opening the door. It replaces a failed lamp component to restore clear, reliable oven cavity lighting. What it does:

• Replaces the oven interior lamp assembly to restore illumination
• Lets you view food without opening the oven door, reducing heat loss
• Commonly used when the oven light is out, flickering, or the lens is cracked
• Works with compatible ranges and wall ovens that use this factory lamp assembly

• Disconnect power to the appliance before installing to avoid shock hazard
• Allow the oven to cool fully; handle bulbs and glass parts carefully to avoid breakage
• Basic hand tools may be required; follow the appliance service manual for access and removal steps