Krfc704fss-01 Parts

Sealer for refrigerant line insulation.

This water tube routes potable water between the water valve and the refrigerator's dispenser or ice maker. Replace a damaged or kinked tube to restore proper water delivery and prevent leaks at the junction points. What it does

• Carries water from the inlet valve to the ice maker or dispenser assemblies
• Prevents kinks and directs flow along the refrigerator cabinet path
• Stops leaks and drips when the original tube is cracked, split, or pinched
• Helps restore normal water dispense and ice production when the tube is the source of the fault

• Disconnect power and shut off the water supply before starting work.
• Inspect and reuse or replace any clamps, ferrules, or fittings only if they show wear.
• Route the tube following the original path to avoid pinches and contact with sharp edges or moving parts.
• After installation, turn on water and power, then check all connections carefully for leaks.

This Crisper Pan replaces a worn, cracked or missing refrigerator crisper drawer pan, restoring a stable surface to hold fruits and vegetables and contain spills. It fits into the crisper compartment to help organize fresh produce. What it does:

• Provides a stable, removable tray for produce storage
• Helps contain leaks and spills in the crisper area
• Replaces cracked, warped or damaged pans that can catch food debris
• Restores proper fit for the crisper drawer to slide smoothly

• Remove any food from the crisper area and slide out the drawer to access the pan
• Lift the old pan out straight to avoid damaging the drawer guides
• Install the new pan by aligning it in the crisper compartment and sliding the drawer back in
• Clean with mild detergent; avoid abrasive cleaners and extreme temperature shocks

This stop door is a replacement door stop that helps the appliance door close securely and stay in position. Restores proper door movement and reduces rubbing or misalignment that can cause noise or poor sealing. What it does:

• Replaces a worn or broken door stop to restore normal door closing and positioning
• Helps prevent the door from bouncing, rubbing, or hanging open
• Can reduce door-related noise and improper sealing during use
• Supports reliable door alignment for safer operation

• Disconnect power to the appliance before starting any repair
• Remove the door or access panel as needed to reach the mounting area
• Typical installation uses basic hand tools (screwdriver, nut driver); retain existing fasteners unless replacement hardware is provided
• Inspect surrounding hinges and catches and replace if damaged

Size: 63-1/2 x 35-1/2 x 2-5/8 inch.

Size: 3/16 inch.

Size: 5/16 inch.

Size: 3/8 inch.

Size: 3/4 inch.

This replacement valve cover protects and secures the washer's inlet valve assembly, helping keep water and wiring contained and reducing risk of leaks or damage. It restores the valve area's original shielding and fit. What it does:

• Covers and protects the water inlet/valve area from splashes and debris
• Helps keep valve wiring and connections properly routed and contained
• Can stop water spray from a damaged or misaligned valve area
• Restores correct mounting/fit to prevent valve movement and noise

• One replacement valve cover

• Disconnect power and shut off water before starting any repair
• Basic hand tools are typically required; access may require removing the top or control panel
• Align cover tabs and secure fasteners until snug; do not overtighten
• Inspect nearby seals, hoses and valve connections while accessible

This genuine replacement clip secures small appliance components in place to prevent rattling and part separation. It restores proper alignment so panels, trim, or internal assemblies stay firmly fastened during normal use. What it does:

• Fastens and retains panels, trim, or small assemblies to the appliance frame
• Prevents parts from shifting, vibrating, or causing operational noise
• Helps maintain proper alignment of connected components
• Commonly replaced when clip is cracked, missing, or no longer holds

• One replacement clip

• Disconnect power (and gas if applicable) before servicing the appliance
• Use needle-nose pliers or a flat tool to remove and install the clip; avoid excessive force
• The clip seats fully in its mounting slots and secures the mating part

This heater is the dryer heating element assembly that provides the heat needed for normal drying cycles, restoring effective drying performance when the element has failed. Installs in the dryer's heater housing to warm incoming air. What it does:

• Heats air that passes through the dryer drum to dry clothes
• Common repair for dryers that produce no heat or take much longer to dry
• Can help resolve intermittent heating or weak heat symptoms when element breaks or shorts
• Works as the primary replaceable heating component in the dryer's heater housing

• Disconnect the appliance from power before starting any repair.
• Replacement requires access to the dryer's rear or front panel and basic hand tools; follow OEM service instructions.
• Inspect related components (thermostats, fuses, wiring, venting) for damage or failures while replacing the heater.

This stop pan is a small replacement part that secures the appliance drain/drip pan and helps keep it seated to reduce movement and leakage risk. It restores the pan's intended fit so the appliance can drain and sit properly. What it does

• Holds the drain/drip pan in position to prevent shifting during operation
• Helps maintain a proper seal and alignment to reduce risk of water contacting chassis parts
• Addresses symptoms like a rattling or loose pan and intermittent water contact under the appliance
• Works as a direct-fit replacement when the original stop is cracked, worn, or missing

• One stop pan

• Unplug the appliance or disconnect power before starting any work
• Remove panels as needed to access the drain/drip pan; basic hand tools are typically required
• Inspect surrounding clips and fasteners and replace if damaged

This door hinge assembly secures and guides the appliance door, restoring proper door alignment and smooth opening and closing. It's a direct-fit replacement that helps stop sagging, rubbing, or difficulty latching. What it does:

• Supports the door on its pivot so the door opens and closes smoothly.
• Restores proper door alignment to improve sealing and prevent gaps.
• Stops door sag, dragging on the cabinet, or uneven closing.
• Works as a direct replacement for the original hinge design.

• Disconnect power to the appliance before starting and follow the manufacturer's safety instructions.
• Use appropriate tools; some models require removing the door or adjusting mounting screws during installation.
• Handle the door carefully to avoid dropping or damaging the hinges or door surface.