Ksm150ps0b Parts

This bearing bracket assembly mounts to the appliance frame and supports a moving mechanism so it slides or pivots smoothly. Replacing a worn bracket restores proper alignment and motion, reducing friction, noise, sticking, and uneven travel.

• Provides a fixed mounting point with an integrated bearing surface for smooth movement
• Keeps the attached component aligned to prevent wobble, binding, and scraping
• Wear or damage can cause rough travel, sticking, squeaking, or sagging
• Cracks, deformation, or a loose fit are common signs the bracket needs replacement

• Disconnect power (and shut off gas, if applicable) and allow the appliance to cool before servicing
• Note the original bracket's location and orientation before removal
• Save and reuse the existing mounting screws/clips
• After installation, operate the mechanism to ensure smooth, unobstructed travel

This factory fastener secures components and panels so your appliance stays assembled and operates safely. Use it to replace a missing or damaged screw to restore a tight, rattle-free fit and help prevent loosening during normal use.

• Holds brackets, panels, or trim securely in place
• Helps resolve issues like loose panels, vibration/rattling, or misaligned parts caused by missing/stripped hardware
• Direct-fit replacement for the original fastener used in applicable assemblies
• Restores proper fastening without modifications

• Unplug the appliance and shut off gas or water supplies as applicable before servicing
• Keep track of original screw locations and lengths; replace like-for-like
• Start threads by hand to avoid cross-threading, then tighten snugly without over-torquing
• If the original hole is stripped, address the hole or use the specified repair method before installation

This speed selector lever is the direct-fit control lever that lets you change fan or motor speeds easily. Restores safe, reliable fingertip control and replaces a cracked, worn, or broken lever. What it does:

• Engages the control shaft so the speed knob can select different motor or fan speeds
• Replaces cracked, snapped, or loose levers that no longer hold the knob securely
• Stops skipping or intermittent speed selection caused by a damaged lever
• Helps restore proper user control without replacing the entire control assembly

• Disconnect power before beginning any repair to avoid electrical shock
• Most installs are simple push-on or fasten with one screw; keep small parts and retainers
• Use basic hand tools; avoid forcing the new lever onto a damaged control shaft
• Inspect those parts before completing installation

This direct-drive gearcase converts the washer motor's power into the agitation and spin motions. Replacing a worn gearcase restores normal drive function so the washer can agitate and spin as intended. What it does

• Transfers motor rotation to the agitator and spin basket for wash and spin cycles
• Worn or damaged gear teeth can cause no agitation or no spin
• Damaged gearcase may produce loud grinding, clunking, or unusual noises during operation
• Failure can cause intermittent drive or loss of drive in one or both cycles

• Disconnect power and water before starting any repair to prevent shock or flooding
• Drain the washer and secure the tub/agitator before removing components
• May require removing the cabinet or access panels and supporting the drum during service

A 10-24 lock nut used to secure threaded fasteners and prevent loosening from vibration. Simple, durable replacement that restores proper fastening where the original nut has worn or failed. What it does:

• Secures shafts, studs, or bolts with 10-24 threads and resists loosening under normal appliance vibration.
• Restores proper tension where a stripped or loose nut causes rattling or parts shifting.
• Helps maintain alignment of panels, brackets, or components that rely on a locked fastener.
• Small hardware solution for common fastening failures—no special part modifications required.

• Disconnect appliance power and water before beginning repairs.
• Use the correct 10-24 threaded fastener and a properly sized wrench or socket to avoid rounding the nut.
• Tighten to a snug fit—do not overtighten or force onto damaged threads.
• Inspect mating threads and replace the bolt/stud if threads are stripped or damaged.

Color: Onyx black

This lever latch is the replacement latch used to secure and release the appliance door or access panel, restoring proper door engagement and user operation. It fits the OEM latch location and matches the original white/storm-gray finish. What it does:

• Replaces a broken, cracked or worn latch lever that prevents the door from closing or latching securely
• Restores smooth open-and-close action for the affected door or panel
• Prevents rattling or misalignment caused by a damaged latch
• Matches the original finish to maintain the appliance appearance

• One lever latch (white/storm-gray), as shown

• Disconnect power to the appliance before beginning any repair
• Remove the damaged latch and install the replacement using the factory mounting points; fasteners or clips may be required depending on model
• Handle small plastic parts carefully to avoid breakage during installation
• Refer to your model-specific parts diagram or service manual for exact removal and reassembly steps

Armature for the electric motor that converts electrical energy into rotation to drive the appliance. Replacing a worn armature can restore motor drive, reduce noise, and help resolve motor-start or power issues. What it does:

• Rotor assembly that creates the rotating magnetic field to turn the motor shaft — symptoms: motor won't start or stalls under load.
• Transfers torque to the motor shaft and works with brushes and the commutator — symptoms: reduced power or weak motor performance.
• Worn or damaged armatures can cause excessive vibration, unusual noise, or visible sparking at the commutator.
• Essential for restoring normal motor operation when the armature is the root cause of motor failure.

• Disconnect power before servicing and follow all safety precautions.
• Replacement typically requires motor removal and disassembly; inspect brushes, commutator, and bearings while servicing.
• Clean and test the commutator and replace brushes if worn to prevent repeat failure.

Color: Almond creme

This armature is the rotating core inside a dryer motor that helps turn the drum and drive airflow. Replacing a worn armature restores proper motor rotation and helps stop noise or failure to tumble. What it does:

• Spins inside the motor to convert electrical energy into mechanical rotation
• Works with the motor's field coil and bearings to drive the dryer drum
• Commonly linked to symptoms like loud grinding or squealing, motor humming without drum movement, or intermittent tumble
• Helps restore normal motor operation when the armature is the source of motor failure

• Designed for use in the motor assembly; inspect bearings, brushes, and field coils when replacing the armature
• Requires disassembly of the motor housing — follow factory service instructions
• Unplug the appliance and disconnect power before beginning any repairs

This replacement Screw-Stat secures the appliance thermostat or temperature sensor so it stays in the correct position for reliable temperature sensing and consistent control performance. Simple, direct replacement for a lost or damaged mounting screw. What it does:

• Secures the thermostat/temperature sensor to the cabinet or mounting bracket.
• Keeps the sensor in firm contact for accurate temperature readings and stable cycling.
• Replaces stripped, missing, or damaged screws that can cause a loose sensor, intermittent temperature control, or rattling.
• Small hardware piece that supports proper operation of the temperature control system.

• Disconnect power to the appliance before accessing internal components.
• Use the proper screwdriver to avoid stripping the screw head; replace with like hardware.
• Do not overtighten—tighten just enough to secure the thermostat without distorting it.

This screw is a factory-style fastener used to secure panels and components in compatible Whirlpool appliances. It restores proper fit and function when the original screw is missing, stripped, or damaged. What it does

• Secures appliance panels, brackets, or small components to prevent rattling and maintain alignment.
• Replaces stripped, corroded, or lost screws to restore a tight, reliable connection.
• Helps eliminate vibration-related noise caused by loose fasteners.
• Fits the original mounting locations where the OEM screw was specified.

• One screw

• Use the correct screwdriver or bit to avoid stripping the head; match thread and length to the original.
• Tighten until snug—do not over-torque to prevent damage to threads or surrounding parts.
• Disconnect power to the appliance before accessing internal components for safety.

This cover is a replacement access panel that protects internal components and restores the appliance's exterior appearance. It keeps wiring and controls shielded while maintaining a clean, finished look. What it does:

• Shields control components and wiring from dust, spills, and accidental contact
• Restores damaged or missing exterior panels for a finished appearance
• Helps maintain proper airflow and component clearance by covering openings
• Can reduce rattles or vibration by replacing a loose or broken panel

• One replacement cover

• Disconnect power (and gas or water if applicable) before starting any repair
• Basic hand tools are typically required; follow the appliance's service manual for specific steps
• Handle edges carefully; align tabs/fasteners before securing to avoid damage
• Replace worn fasteners or clips to ensure a secure fit