Ksm150psb Parts

This insert is a small, model-specific fitting that seats inside its assembly to align and secure the mating component. Replacing a cracked or missing insert restores a tight fit, correct positioning, and smooth operation.

• Provides the alignment/seating interface within the related assembly
• Helps the attached part fasten and sit properly
• Restores correct spacing and positioning for smooth operation
• Symptoms include a missing/broken insert, loose or wobbly component, difficulty securing or closing, or visible gap/misalignment

• Unplug the appliance and shut off water/gas before service
• Refer to your model's parts diagram for exact placement and orientation
• Transfer/reuse any original screws, clips, or fasteners as required
• Do not overtighten; confirm alignment and test operation afterward

Fastens internal components in your stand mixer. Replace this screw if stripped, corroded, or missing to secure panels and brackets properly.

This replacement screw is a direct-fit fastener used to secure appliance panels and components, restoring proper fit and reducing movement. Ideal when original screws are stripped, missing, or damaged. What it does:

• Secures panels, trim, brackets, and other serviceable components to prevent rattling or misalignment
• Matches original fastener form for correct fit and reliable function
• Helps restore proper clearance and component alignment after repair
• Safe, general-purpose replacement for common appliance fastening needs

• Turn off power and disconnect the appliance before accessing internal components
• Use the correct screwdriver or bit; avoid overtightening to prevent thread or part damage
• Keep hardware and small parts away from children and pets

Factory-matched Almond Crème touch-up paint for stand mixers. Covers small chips, scratches, and worn spots on Almond-finish appliances for a cleaner look.

Almond Creme finish panel for stand mixers. Restores exterior appearance when original panel is scratched, worn, or discolored. Direct replacement.

This replacement Screw-Stat secures the appliance thermostat or temperature sensor so it stays in the correct position for reliable temperature sensing and consistent control performance. Simple, direct replacement for a lost or damaged mounting screw. What it does:

• Secures the thermostat/temperature sensor to the cabinet or mounting bracket.
• Keeps the sensor in firm contact for accurate temperature readings and stable cycling.
• Replaces stripped, missing, or damaged screws that can cause a loose sensor, intermittent temperature control, or rattling.
• Small hardware piece that supports proper operation of the temperature control system.

• Disconnect power to the appliance before accessing internal components.
• Use the proper screwdriver to avoid stripping the screw head; replace with like hardware.
• Do not overtighten—tighten just enough to secure the thermostat without distorting it.

If your mixer won't spin or makes grinding noises, the planetary gear assembly may be worn. This part transfers motor power to attachments. Moderate DIY.

This cap fits over the brush holder to protect and secure the motor brushes, helping maintain proper brush alignment and motor contact. Replaces a worn or damaged cap to restore reliable motor brush seating and protection. What it does:

• Covers and secures the motor brush holder to keep brushes properly positioned
• Helps prevent debris from interfering with brush contact and motor operation
• Used when the cap is cracked, broken, or missing and brush retention is compromised
• Can reduce intermittent motor stopping or rough operation caused by loose brushes

• Disconnect power before starting any repair to avoid electrical shock
• Remove the appliance access panel to reach the motor brush assembly; handle components carefully
• Inspect brushes and springs while replacing the cap; replace brushes if excessively worn

Fix excessive vibration or unusual motor noise with this stand mixer motor housing. Secures and aligns the motor for stable, quiet operation.

Replacement screw for stand mixer assembly. Secures internal or external components. Order when original screw is stripped, missing, or damaged.

Replaces the front grille housing on your stand mixer. Needed when the original is cracked, warped, discolored, or missing. Almond creme finish.

Supports moving mechanisms in your stand mixer for smooth operation. Replace if you notice excessive noise, wobbling, or oil leaks. Verify fit with your model.

Replacement mounting screw for stand mixers. Secures panels, brackets, and internal components. Needed when original is missing, stripped, or damaged.