Ksm5op Parts

Replacement base for stand mixers. Installs as the main housing unit. Order a new base if yours is cracked, damaged, or structurally compromised.

Protects and secures hinge or pivot pins on mixer attachments. Replace if cracked, broken, or missing to prevent metal wear and keep pins properly seated.

If your stand mixer bowl won't raise or lower properly, this lift rod secures and positions the bowl lift mechanism, eliminating loose or stuck movement.

This speed control assembly regulates motor speed to restore proper agitation and spin in compatible laundry appliances. Replacing a faulty speed control helps stop erratic speeds and restore normal cycle operation. What it does:

• Controls motor speed signals so the washer can agitate, spin, and change speeds as programmed
• Common symptom: washer fails to agitate or spin, or runs at inconsistent speeds
• Can address issues where cycles stall or do not complete due to speed control faults
• Works as the electronic interface between the timer/control and the motor

• One speed control assembly

• Disconnect power before beginning any repair to avoid shock hazard
• Replacement typically requires access to the control housing; keep track of screws and wiring
• Match part number to your appliance before installation; wire connectors are usually keyed but note positioning before removal

Fixes mixer that won't start, stops under load, or runs weak. This motor armature restores full speed and power when the rotor assembly fails.

Lift arm rod for stand mixers. Connects the lift handle to the bowl support mechanism. Replace if bent, stripped, or the lift assembly is jammed.

Fix mixer wobbling or grinding noises with this planetary gear assembly. Essential for smooth mixing action. Moderate repair with periodic greasing.

If your stand mixer is excessively noisy or vibrating, the motor housing may be cracked or damaged. This white housing secures and protects the motor.

A white replacement bowl support that centers and stabilizes the appliance bowl or glass tray to reduce wobble and noise, helping restore smooth rotation and reliable operation. What it does:

• Centers and supports the bowl or glass tray to prevent off-center rotation and rubbing.
• Keeps the tray steady to reduce vibration and noisy operation.
• Helps the tray rotate smoothly for even heating or proper function.
• Common symptoms it can address: wobbling or off-center bowl/tray, noisy rotation, scraping or unstable tray movement.

• Disconnect power to the appliance before starting any work.
• Remove the bowl or glass tray and lift out the old support; inspect the drive hub or shaft for damage.
• Align the support over the hub/shaft and press into place until fully seated; do not force broken or warped plastic.

Genuine 10-24 thread screw secures panels, brackets, and assemblies in stand mixers. Replace when stripped, missing, or corroded for proper fit.

This cap fits over the brush holder to protect and secure the motor brushes, helping maintain proper brush alignment and motor contact. Replaces a worn or damaged cap to restore reliable motor brush seating and protection. What it does:

• Covers and secures the motor brush holder to keep brushes properly positioned
• Helps prevent debris from interfering with brush contact and motor operation
• Used when the cap is cracked, broken, or missing and brush retention is compromised
• Can reduce intermittent motor stopping or rough operation caused by loose brushes

• Disconnect power before starting any repair to avoid electrical shock
• Remove the appliance access panel to reach the motor brush assembly; handle components carefully
• Inspect brushes and springs while replacing the cap; replace brushes if excessively worn

This is the outer motor housing shell for a stand mixer in an onyx black finish. It covers and protects the motor and internal components while giving the mixer its exterior appearance. Replace this housing if it is cracked, chipped, or cosmetically damaged.

This is the upper motor housing for a stand mixer, finished in Empire Red porcelain enamel. It encloses and protects the motor and internal drive components of the mixer. Replace this housing if it is cracked, chipped, or damaged, which can expose internal parts to debris and compromise the appearance and structural integrity of the mixer.

Small flat washer for KitchenAid stand mixers. Installs between mechanical components to ensure proper spacing. Replace if worn, cracked, or missing.

This is the planetary gear assembly for a stand mixer, which drives the rotating motion of the mixer attachments in an orbital path around the inside of the bowl. It connects the motor's output to the attachment hub, ensuring thorough and even mixing. Replace this part if the mixer head wobbles excessively, attachments spin erratically, or the mixing action becomes uneven or stops altogether.