Kuck031tbl0 Parts

This small conical washer is used in select washer assemblies to maintain clamp force under vibration. It helps keep fasteners tight and components properly aligned for reliable wash and spin performance. What it does:

• Provides spring-like tension under a screw or bolt to maintain clamp load
• Helps prevent fasteners from loosening due to vibration
• Supports proper alignment and secure fit of mating parts
• Worn or missing washers can lead to rattling, looseness, or intermittent operation

• 1 cone washer

• Disconnect power and, if applicable, turn off water supply before servicing
• Access the relevant assembly per your model's service information
• Note the washer's original orientation and match it during reassembly
• Tighten hardware securely without over-torquing; test and recheck for security

Replacement stringer bolt that secures the appliance's stringer or support rail to the cabinet frame, restoring panel alignment and preventing movement. Use when the original bolt is missing, loose, or damaged. What it does:

• Secures the stringer/support rail to the appliance frame so panels and assemblies stay aligned.
• Helps prevent cabinet or panel movement that can cause rattling or vibration during operation.
• Restores proper alignment when a loose or missing bolt causes misaligned panels or binding doors.
• Simple, direct replacement for a corroded, stripped, or lost fastener.

• Disconnect power before working on the appliance and remove any panels.
• Use the correct-size socket or wrench; hand-tighten, then snug—do not overtighten to avoid stripping threads.
• Inspect mating threads and replace the bolt if heads or threads are damaged; for the correct fastener location.

This latch plate secures the appliance door to the cabinet, providing the positive engagement needed for proper door closure and operation. It helps restore a door that won't stay closed or won't trigger door switches. What it does:

• Acts as the door strike that the latch engages to hold the door shut
• Ensures the door closes firmly so door switches can register a closed state
• Can stop issues like a loose or misaligned door, or a door that won't remain closed
• Restores proper alignment and engagement without replacing the full latch assembly

• Disconnect power (and gas if applicable) before servicing
• Remove the door or access panel to reach the latch area
• Inspect related latch components and alignment; replace only the damaged part
• Use basic hand tools; tighten fasteners securely but avoid overtightening

This drive chain connects a washer's motor/transmission to the agitator or drum, transferring rotational motion so the wash basket spins and agitates properly. Replaces a worn or broken chain to restore normal drive function. What it does:

• Transfers motor torque to the transmission/agitator so the tub spins and agitates
• Commonly replaced when the washer won't agitate or spin despite motor running
• Replaces stretched, rusted, or broken chain that causes slipping or unusual noise
• Works as a direct mechanical link—no electrical components involved

• Install with the appliance unplugged and water supply turned off; follow OEM service manual for alignment and tension
• May require partial disassembly of cabinet, pulley, or transmission; have basic hand tools ready
• Inspect sprockets, tensioners, and related components and replace if excessively worn

This is a replacement machine screw sized 8-18 x 3/8 that secures panels and components on compatible appliances. It restores proper fastening where a worn, stripped, or missing screw causes loose parts or rattling. What it does

• Fastens control panels, trim pieces, or brackets to the appliance chassis
• Replaces stripped, corroded, or missing screws that cause loose panels or vibrating noise
• Provides correct thread engagement for a secure hold in tapped holes
• Small hardware solution often used during door, console, or interior repairs

• One 8-18 x 3/8 machine screw (quantity: 1)

• Use the correct screw size and thread; do not force a different-size fastener into tapped holes
• Hand-start the screw to avoid cross-threading, then tighten with the appropriate screwdriver
• Disconnect power before accessing internal components or panels on electrical appliances
• If metal threads are damaged, repair with a helicoil or replace the damaged component rather than over-torquing

This wave washer is a small, wavy metal retainer that holds rotating or sliding components in place on a shaft. It helps maintain proper alignment and reduces end-play for smoother, quieter operation. What it does:

• Secures components on a shaft to prevent axial movement and maintain alignment
• Helps reduce vibration and rubbing that can cause noise or premature wear
• Commonly used behind agitator, cam, or bearing assemblies where axial retention is required
• Replace if the washer is deformed, cracked, or missing to restore correct component spacing

• Disconnect power before starting repairs
• Remove the affected assembly (agitator/shaft or other specified part) to access the washer
• Install the washer in the same orientation and position as the original; ensure it seats fully
• Inspect surrounding components (bushings, seals, bearings) and replace any worn parts to prevent repeat failure

Bottle with brush. Acyrlic touch-up paint. Color: Empire red. Size: 0.6 fl.oz.

This safety switch actuator engages the door/interlock switch so the appliance senses a closed, secure door and will run as intended. Replacing a worn actuator restores reliable door engagement and control-system signaling. What it does:

• Moves the door latch into position to trip the appliance's safety/interlock switch
• Ensures the control board senses a closed door so cycles can start or continue
• Common symptom: appliance won't start or stops when the door is shut or nudged
• Common symptom: door won't fully latch or feels loose when closing

• One safety switch actuator

• Disconnect power (and water if applicable) before starting any repair
• Remove exterior panels or door assembly as needed to access the actuator; keep fasteners organized
• Verify switch alignment with the actuator and test operation before reassembly
• Wear gloves and eye protection

This deodorant is a replacement refrigerator deodorizer that helps reduce common food and household odors inside the fresh-food compartment for a cleaner-smelling interior. Simple swap helps maintain a neutral-smelling refrigerator. What it does:

• Adsorbs and reduces odors in the refrigerator interior to help keep food-smelling fresher
• Fits into the refrigerator deodorizer holder or designated compartment
• Works passively—no power or batteries required
• Helps refresh interior air between routine cleaning cycles

• For best results, remove old deodorizer and place new cartridge in the designated holder
• Disconnect power before beginning
• Wash hands after handling and follow local disposal guidelines for used cartridges
• If odors persist, inspect seals, drains, and spoiled food before replacing the deodorizer

Size: 6-32 x 3/8 inch.

This C-shaped retaining ring snaps into a groove on a shaft or pin to hold a component in place. It restores secure retention so parts don't slide off or shift during operation.

• Snaps into a groove to secure parts on a shaft or pin
• Prevents axial movement to keep assemblies aligned
• Helps reduce wobble, rattling, or parts migrating off
• Common signs: missing/broken clip, loose mechanisms, parts slipping off during use

• Disconnect power; also shut off water or gas as applicable
• Wear eye protection—retaining clips can spring free during removal/installation
• Use appropriate snap/retaining ring pliers or a small flat tool; avoid over-expanding the ring
• Ensure the ring seats fully in the groove and replace if bent or fatigued

Bottle with brush. Acyrlic touch-up paint. Color: Cobalt blue. Size: 0.6 fl.oz.

A small slotted pin spring used to secure moving parts in appliance assemblies. This compact replacement restores proper retention and alignment where a slotted spring pin is required, helping moving parts stay in place and operate smoothly. What it does:

• Acts as a slotted spring pin to hold shafts, levers or clips in position
• Restores secure retention when original pin is bent, worn or missing
• Prevents excess play or disengagement of connected components
• Helps resolve symptoms like loose or shifting parts, rattling, or components not staying engaged

• One slotted pin spring

• High-level replacement; retains existing mating hardware and holes
• Use proper tools (needle-nose pliers, punches) to remove/install without damaging surrounding parts
• Wear eye protection; pins can release under tension during removal

Size: 8-32 x .312 inch.

This flat metal washer provides a durable spacer and load-bearing surface for fasteners in the appliance, helping maintain proper alignment and reduce wear on mating parts. It's a simple replacement that restores correct assembly spacing. What it does:

• Acts as a load-distributing spacer between fastened components to prevent loosening and wear
• Helps maintain proper alignment of shafts, housings, or assemblies
• Can reduce vibration or movement caused by uneven mating surfaces
• Commonly replaced when hardware is corroded, damaged, or missing

• One flat metal washer (quantity: 1)

• Verify the exact washer size and thickness before installation; replace with the same type
• Tighten fasteners to the manufacturer's torque specifications when known; avoid overtightening
• If used near electrical connections, ensure power is disconnected before working
• Inspect adjacent fasteners and components for wear and replace if necessary