Kuid508hps Parts

The Water Pan is an OEM part for Whirlpool free-standing ice machines. It collects and stores water to be used in the ice making process. As water is frozen into ice in the evaporator, it needs to be replenished to maintain proper levels. The water pan is designed to hold water and release it into the evaporator efficiently. 

Causes for a bad water pan can include cracking, leaking, or corrosion that affects its ability to hold water. Over time, repeated heating and cooling cycles can cause weakening of the material. 

Symptoms of a bad water pan include:

• Ice maker not producing ice or producing less ice than normal 
• Water leaks in the ice maker compartment
• Improper water levels seen during the ice-making process
• Error codes related to water levels

This OEM Whirlpool replacement part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

The Reservoir Drain Tube is an OEM part for Whirlpool freestanding icemakers. It is responsible for draining melted water from the reservoir during the harvest cycle. This tube removes water to allow for new ice formation. 

Causes of a bad reservoir drain tube can include mineral buildup or blockages within the tube inhibiting proper drainage over time. Additional causes may be cracks, cracks, kinks, or other damage limiting water flow.

Symptoms of a bad reservoir drain tube include:

• Water not draining from the reservoir after harvest
• Excess water collecting in the reservoir 
• Slow or reduced ice production due to poor drainage
• Leaks or water spills around the drain tube area

This OEM Whirlpool replacement tube is also compatible with freestanding ice components manufactured by select Kenmore models. 

The Pump Harness is an OEM replacement part for Whirlpool icemakers. It connects the icemaker pump to the electrical system of your refrigerator, ensuring proper power supply. It provides a secure and reliable connection, allowing the pump to operate efficiently and deliver a consistent flow of water to the icemaker.

A bad wiring harness can occur due to various reasons, such as wear and tear, exposure to moisture or extreme temperatures, or accidental damage. If you notice symptoms such as the icemaker not producing ice, inconsistent or weak water flow, or a malfunctioning pump, it may be time to replace the wiring harness.

Causes of a bad icemaker pump wiring harness include:

• Wear and tear over time
• Exposure to moisture or extreme temperatures
• Accidental damage or improper handling

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

Size: 8-18 x 1/2 inch.

Replace a damaged or leaking tube with this quality replacement to restore a secure, routed connection inside your appliance. It helps direct flow between components so fluid reaches the right place and stays contained. What it does:

• Directs flow between fittings, valves, reservoirs, dispensers, or ice makers
• Maintains proper routing to prevent leaks and ensure normal operation
• Common failure modes include cracks, pinholes, kinks, and clogs
• Symptoms include leaks inside/under the unit, reduced or no flow to a connected component, or visible damage to the tube

• 1 tube

• Disconnect power and shut off the supply to the unit (water, if applicable) before servicing
• Note the original routing and connection points; take photos for reference
• Fully seat the tube in connectors/compression fittings; avoid sharp bends and contact with hot or moving parts
• Restore supply and check all connections for leaks

Size: 8 x 1-1/4 inch.

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

Size: 8-18 x 5/8 inch.

This solenoid valve coil is the electromagnetic coil that actuates a valve in your appliance. Replacing a weak or open coil helps restore reliable opening and closing for consistent filling or dispensing performance.

• Energizes the valve armature to start or stop flow as directed by the control
• Common symptoms: no fill/dispense, intermittent or slow flow, or a coil that tests open/no continuity
• A targeted fix when the valve body is intact and not stuck or leaking
• Use to replace a burned, cracked, or shorted solenoid coil on the original valve assembly

• Disconnect power and shut off supply lines before service
• Access the valve, note wire positions, and remove any retaining clip or fastener
• Slide the old coil off the stem; install the new coil in the same orientation and reconnect wires securely
• Restore power/supply and test operation; check for leaks

The Water Filter Housing is an OEM part for Whirlpool ice machines. It holds and secures the water filter, ensuring clean and filtered water for your ice machine. This water filter housing provides a tight seal to prevent leaks and maintain the filtration system. 

A bad water filter housing can occur due to wear and tear over time or damage caused by improper installation or mishandling. If you notice symptoms such as water leaks around the filter housing, difficulty in installing or removing the water filter, or a loose or damaged housing, it may be time to replace this part.

Symptoms of a bad water filter housing include:

• Water leaks around the filter housing
• Difficulty in installing or removing the water filter
• Loose or damaged housing

Restore your ice machine by replacing the faulty or damaged water filter housing with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement switch restores the electrical control function for the appliance, letting the associated component respond correctly when activated. It provides a straightforward swap to return reliable on/off or sensing operation. What it does:

• Opens or closes an electrical circuit to control power to a specific component.
• Stops or allows a component to run when the switch is operated (safe symptom linkage: appliance won't start, a specific function won't respond, or an interior light/motor won't operate).
• Matches the original mounting and terminal locations for a direct replacement when this exact part number is required.
• Works as the user-replaceable control switch for the affected function.

• Always disconnect power to the appliance before beginning service.
• Handle terminals carefully and make secure electrical connections; avoid bending or damaging pins.
• After installation, restore power and test the appliance operation to confirm proper function.

This 18" door gasket seals the appliance door to help maintain proper temperature and efficiency. It replaces a worn or damaged seal so the appliance can run normally and reduce energy loss. What it does:

• Creates a tight seal around the door to help prevent air leaks and temperature drift
• Helps reduce frost or moisture buildup caused by a failing gasket
• Can stop excessive cycling or longer run-times tied to seal failure
• Restores proper door closure for consistent performance

• Disconnect power to the appliance before starting any repair
• Remove the old gasket carefully; some adhesive or retainer clips may be present
• Inspect the door and retainer for damage or debris before installing the new gasket

This is a genuine replacement screw used to secure components and panels on compatible Whirlpool appliances, restoring a firm, vibration-free fit. It replaces worn or missing fasteners to help keep parts aligned and stable. What it does

• Secures panels, brackets, or internal components to prevent shifting or rattling
• Replaces stripped, rusted, or missing screws that cause loose parts or noise
• Helps maintain proper alignment of mounted components for safe operation
• Useful when reassembling repair work or after removing parts for service

• One replacement screw

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread damage
• Disconnect power before servicing electrical appliances; follow OEM safety guidance
• If screw threads or holes are damaged, replace both screw and mating hardware as needed

Size: 8-18 x 1 1/4 inch.