Kuis1851 Parts

This white end cap panel replaces a worn, cracked or discolored side trim to restore the appliance's finished look and protect internal edges. It's a direct-fit cosmetic part that keeps the console area looking clean and complete. What it does:

• Covers and protects the outer edge of the control/console area to hide gaps and mounting points
• Restores uniform appearance when original trim is cracked, broken or faded
• Helps prevent dust and debris from entering side cavities
• Re-establishes proper corner alignment for adjacent trim pieces

• Turn off and unplug the appliance before starting any repair.
• Remove any adjacent trim or screws blocking the end cap; use appropriate hand tools.
• Align tabs or mounting pegs, then press or fasten gently—do not force parts into place.

This hinge spring is the OEM replacement tension spring that helps support and balance the oven/range door for smooth opening, controlled closing, and proper door positioning. Restores stable door movement and reduces sudden drops. What it does:

• Provides tension to the door hinge so the door opens and closes smoothly
• Helps keep the door in the intended open or partially open position
• Reduces door sag, slipping, or sudden closing
• Can stop noisy or uneven hinge movement caused by a worn spring

• Disconnect power to the appliance before starting any repair.
• Use gloves and eye protection; springs are under tension and can snap back.
• Follow the manufacturer's removal/installation steps — you may need to partially or fully remove the door to access the hinge spring.

This support bracket holds the evaporator/grid assembly in place inside the freezer compartment, helping maintain proper airflow and alignment for consistent cooling. Durable replacement for damaged or missing mounts. What it does:

• Secures the evaporator or evaporator grid to the cabinet to prevent movement and vibration
• Keeps the evaporator properly positioned for even airflow through the freezer
• Helps reduce rattling or noise caused by a loose evaporator assembly
• Can prevent contact that leads to coil damage or improper defrosting

• One support bracket

• Disconnect power to the appliance before beginning any disassembly
• Remove necessary panels and shelving to access the evaporator area; handle the evaporator coil/grid carefully to avoid bending or puncturing
• Reuse existing fasteners when possible; replace any damaged clips or screws with OEM-recommended hardware

Size: 8-32 x 1/2 inch.

This wire harness connects the ice maker's cutter grid to the appliance's electrical system, supplying power so the heated grid can slice the ice slab into cubes. Replacing a damaged harness helps restore consistent cube separation and production.

• Routes electrical power to the cutter grid/heating wires
• A failed, loose, or heat-damaged harness may prevent the grid from warming
• Common symptoms may include whole sheets or large chunks in the bin, cubes not separating, or intermittent/slow ice production
• Visual signs can include melted/discolored grid connectors or broken/brittle conductors

• Disconnect power before servicing; allow the cutter grid to cool completely
• Note wiring/connector orientation; transfer one connection at a time to match original routing
• Seat connectors fully and secure the harness in original clips/standoffs away from sharp edges
• After reassembly, restore power and verify the cutter grid warms during a cycle

This front-and-rear mounting bracket secures the appliance's front and rear assemblies to the cabinet, restoring proper alignment and support. Replacing a worn or damaged bracket helps reduce panel movement, rattling and improper fit. What it does:

• Provides a stable mounting point for the appliance's front and rear assemblies to maintain alignment and cabinet integrity.
• Stops or reduces rattling, vibration and shifting caused by loose or broken mounting hardware.
• Prevents gaps and misalignment that can affect doors, panels or controls.
• Fits original mounting locations to restore factory support.

• Bracket (front and rear)

• Disconnect power (and water if applicable) before starting any repair.
• Use the original fasteners or manufacturer-recommended hardware; do not force or bend the bracket.
• Inspect adjacent mounting points and fasteners for wear; replace any damaged parts.

This is a replacement left/right mounting bracket used to secure interior panels or trim and restore proper alignment and fit. It provides a simple fix for loose panels and misalignment without replacing larger assemblies. What it does:

• Secures an interior panel, trim piece, or rail to the appliance cabinet
• Restores proper alignment to reduce rubbing or binding of doors or panels
• Prevents rattling or movement caused by worn or broken brackets
• Helps maintain correct spacing for connected components

• Basic hand tools typically required; refer to your appliance's service manual for the exact procedure
• Disconnect power (and gas if applicable) before beginning any repair to avoid shock or injury
• Keep removed fasteners and parts organized for reassembly; replace any damaged screws

This part is a replacement water circulation pump. It is intended for use with a variety of different ice maker models. This pump works to ensure that water is properly circulated over the ice maker's evaporator plate. This forms the ice, which is then cut into cubes. If this circulation pump if malfunctioning, the ice maker may not be able to produce ice efficiently, if at all. Ensure the appliance is entirely disconnected from the power and water source before attempting any repairs. It's recommended that work gloves are worn for proper protection.This is a genuine OEM part made by Whirlpool and has been sourced directly from the manufacturer. This water circulation pump is suitable for use on a variety of refrigerator models manufactured by Whirlpool, Maytag, Kitchenaid, Kenmore, and some other brands. It is a genuine OEM part and thus is manufactured from high-quality, durable materials. Part sold individually.