Kusi185jbl Parts

This push nut fastener is a small push-on retainer used to secure shafts, studs, or trim where a low-profile, tool-free hold is required. It provides a reliable, vibration-resistant connection to keep components in place. What it does:

• Holds shafts, studs, or panels by gripping the tapered shaft when pressed on
• Prevents loosening from vibration and normal use
• Useful for securing trim, brackets, shields, or small assemblies
• Commonly used where a permanent or semi-permanent push-fit retention is needed

• Press onto clean, correctly sized shaft until fully seated; do not hammer on delicate components
• Wear eye protection when installing to guard against snapping or flying debris
• For service requiring disassembly of electrical components, disconnect power first

Size: 1/4 lb.

Size: 1/4 inch.

This hinge spring is the OEM replacement tension spring that helps support and balance the oven/range door for smooth opening, controlled closing, and proper door positioning. Restores stable door movement and reduces sudden drops. What it does:

• Provides tension to the door hinge so the door opens and closes smoothly
• Helps keep the door in the intended open or partially open position
• Reduces door sag, slipping, or sudden closing
• Can stop noisy or uneven hinge movement caused by a worn spring

• Disconnect power to the appliance before starting any repair.
• Use gloves and eye protection; springs are under tension and can snap back.
• Follow the manufacturer's removal/installation steps — you may need to partially or fully remove the door to access the hinge spring.

This support bracket holds the evaporator/grid assembly in place inside the freezer compartment, helping maintain proper airflow and alignment for consistent cooling. Durable replacement for damaged or missing mounts. What it does:

• Secures the evaporator or evaporator grid to the cabinet to prevent movement and vibration
• Keeps the evaporator properly positioned for even airflow through the freezer
• Helps reduce rattling or noise caused by a loose evaporator assembly
• Can prevent contact that leads to coil damage or improper defrosting

• One support bracket

• Disconnect power to the appliance before beginning any disassembly
• Remove necessary panels and shelving to access the evaporator area; handle the evaporator coil/grid carefully to avoid bending or puncturing
• Reuse existing fasteners when possible; replace any damaged clips or screws with OEM-recommended hardware

Size: 8-32 x 1/2 inch.

The condenser fan motor is an OEM part for Whirlpool refrigerators. It plays a vital role in circulating refrigerant through the condenser coils, facilitating heat exchange and maintaining the refrigerator's cooling efficiency.

Over time, the motor-condenser can wear out or fail due to electrical issues, mechanical wear, or blockages in the condenser system. A malfunctioning motor can compromise the refrigerator's cooling performance, leading to temperature fluctuations and increased energy consumption.

Symptoms of a bad Motor-Condenser include:

• The refrigerator not cooling properly
• Unusual noises coming from the back of the refrigerator
• The compressor running continuously
• Increased energy bills due to inefficient operation
• Overheating of the refrigerator

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This wire harness connects the ice maker's cutter grid to the appliance's electrical system, supplying power so the heated grid can slice the ice slab into cubes. Replacing a damaged harness helps restore consistent cube separation and production.

• Routes electrical power to the cutter grid/heating wires
• A failed, loose, or heat-damaged harness may prevent the grid from warming
• Common symptoms may include whole sheets or large chunks in the bin, cubes not separating, or intermittent/slow ice production
• Visual signs can include melted/discolored grid connectors or broken/brittle conductors

• Disconnect power before servicing; allow the cutter grid to cool completely
• Note wiring/connector orientation; transfer one connection at a time to match original routing
• Seat connectors fully and secure the harness in original clips/standoffs away from sharp edges
• After reassembly, restore power and verify the cutter grid warms during a cycle