La513 Parts

This agitator spring maintains the spring tension inside the washer's agitator assembly so the wash action engages reliably. When fatigued or missing, the agitator can slip, feel loose, or make clicking/ratcheting noises during the cycle.

• Provides spring tension within the agitator assembly
• Helps keep agitator components properly engaged for consistent wash action
• Symptom: upper agitator/auger slips or fails to advance
• Symptom: weak or intermittent agitation
• Symptom: clicking/ratcheting noises or a loose-feeling agitator

• Disconnect power and turn off water before servicing
• Remove the agitator cap and bolt/retainer to access internal components
• Note the order and orientation of parts; seat the new spring correctly before reassembly
• Snug the agitator bolt and reinstall caps; run a test cycle to ensure proper agitation

This spring-timer knob replaces a worn, cracked or missing timer knob so you can set and adjust the appliance's mechanical timer reliably. Simple, direct replacement that restores the user control interface. What it does:

• Fits onto the appliance's mechanical timer shaft to allow setting and advancing the timer
• Restores a secure grip and pointer for accurate time selection
• Commonly used to fix loose, cracked, stripped, or missing timer knobs
• Helps resolve inability to turn or set the mechanical timer caused by a damaged knob

• Disconnect power to the appliance before starting any repair
• Pull the old knob straight off the timer shaft; align splines and press the new knob fully onto the shaft until seated
• If the knob is tight, use a proper knob puller or gentle, even leverage to avoid damaging the shaft

A cam sleeve that supports and guides the cam on its shaft to keep the cam-driven mechanism moving smoothly. Replacing a worn sleeve helps restore correct alignment and reduces binding or intermittent movement. What it does

• Centers and stabilizes the cam on its shaft for reliable engagement.
• Prevents metal-on-metal wear between the cam and shaft.
• Helps eliminate binding, wobble, or uneven operation caused by a worn sleeve.
• Common symptom of failure: noise, sticking, or irregular movement from the cam-driven mechanism.

• Disconnect power to the appliance before beginning any repair.
• Access typically requires removing the appropriate service panel; follow the model service manual.
• Inspect mating cam and shaft for wear; replace any damaged components.
• Reassemble panels and verify proper operation before returning the appliance to service.

A replacement thrust bearing that supports the washer transmission shaft to reduce axial wear and help the gearbox rotate more smoothly. Use this bearing to address noisy transmission operation and reduce metal-on-metal wear when the original is worn. What it does:

• Supports axial load on the transmission/gearcase shaft to reduce friction and wear
• Helps prevent grinding, scraping, or other metal-on-metal noises from the gearbox
• Can reduce rough or noisy spin and improve agitation when a worn bearing is the cause
• Helps maintain proper alignment of transmission components for smoother operation

• Disconnect power and water supply and drain the washer before beginning any work.
• Replacement requires accessing the agitator/gearcase per the OEM service manual and may involve transmission/gearcase disassembly.
• Inspect nearby seals, fasteners and other bearings while servicing; replace damaged parts to avoid premature failure.

Bottle with brush. Color: Platinum. Size: 0.6 fl.oz.

This idler pulley guides and maintains tension on the dryer drive belt to help the drum rotate smoothly. Replacing a worn pulley restores correct belt tracking and reduces noise from rubbing or slipping. What it does

• Guides the dryer drive belt and keeps proper belt tension
• Helps the drum turn smoothly during normal operation
• Commonly used when you hear squeaking, grinding, or belt slipping noises
• Prevents premature belt wear and misalignment

• One idler pulley

• Disconnect power before starting any repair; the appliance is de-energized
• Basic hand tools required; remove the front or access panel and drum as needed per your model's service instructions
• Inspect the belt and bearing surfaces; replace belt if damaged or glazed
• Do not lubricate the pulley unless the OEM specifically directs it; replace if bearing is noisy or seized

This motor shield protects and secures the appliance motor assembly, helping block debris and contact with nearby components so the motor can run reliably. It's a direct-fit replacement for a damaged or missing motor shield. What it does

• Shields the motor from debris and foreign objects that can cause rubbing or obstruction.
• Helps secure and position the motor within the cabinet to maintain proper alignment.
• Reduces risk of contact between the motor and other parts that can cause noise or wear.
• Replacing a cracked or missing shield can prevent recurring motor issues and reduce abnormal sounds.

• Disconnect power to the appliance before beginning any repair.
• Use basic hand tools; avoid forcing fasteners or damaging adjacent components.
• Wear gloves to protect against sharp edges on the shield or mounting area.

Rear panel pad cushions and insulates the appliance's rear cabinet to reduce vibration, noise and rubbing against the back panel. Replacing a damaged pad helps stop rattles and protects internal components from wear. What it does:

• Provides rear-cabinet cushioning and thermal/abrasion protection for the back panel.
• Dampens vibration and reduces operational noise.
• Prevents direct metal-to-metal contact that can cause rubbing or wear.
• Common symptom fix: reduces rattling or vibrating noises from the appliance rear.

• Always disconnect power (and gas, if applicable) before starting any repair.
• Remove the rear access panel to access the pad; replace using the original mounting points, adhesive or clips.
• Inspect surrounding insulation and mounting hardware; replace any damaged fasteners.

This rubber lid bumper cushions the washer lid to prevent hard contact and reduce noise and wear. It replaces a worn or missing bumper to help the lid close more softly and sit level. What it does:

• Acts as a soft contact point between the lid and cabinet to absorb impact
• Reduces lid slamming, rattling, and vibration during operation
• Helps keep the lid aligned and prevents cosmetic damage to the rim
• Commonly replaced when the bumper is cracked, flattened, or missing

• One rubber lid bumper

• Install by removing the old bumper and pushing the new bumper into the mounting hole or recess; hand tools may be helpful
• Ensure the appliance is powered off and disconnected before servicing
• Inspect surrounding mounting area for damage and replace any broken retainers as needed
• If the bumper is hard to seat, warm it briefly with a hair dryer to improve flexibility

This is a replacement drum drive belt that turns the dryer drum so clothes tumble and dry evenly. A direct-fit belt for restoring normal drum rotation and preventing slipping or squealing. What it does

• Wraps around the dryer drum and drive pulley to transfer motor power to the drum.
• Keeps the drum rotating smoothly to ensure even drying and prevent overheating.
• Designed to match OEM fit and length for proper tension and long wear.

• Disconnect power (and gas supply if applicable) before starting any repair.
• Inspect pulleys and idler for wear when replacing the belt; replace any worn parts to prevent repeat failure.
• Follow the dryer's service manual for belt routing and correct tension.

This tub seal kit replaces a worn or damaged tub gasket to restore the appliance's watertight seal and reduce leaks. It's a direct-replacement style kit used during tub or pump repairs to help maintain proper sealing. What it does:

• Replaces the tub sealing components that prevent water from escaping the tub area
• Helps stop common leak symptoms like puddling or water on the floor near the appliance
• Restores a secure seal after tub or pump disassembly to reduce moisture-related damage
• Useful when service shows visible gasket wear, cracks, or hardening

• Disconnect power and water supply before starting any repair
• Drain the appliance and remove any obstructing panels to access the tub area
• Follow the OEM service manual for disassembly and correct seal orientation

This bracket assembly secures a switch and thermal fuse used to control power and protect the appliance from overheating. It replaces a worn or failed mounting assembly to restore proper electrical safety and switch function. What it does:

• Holds the switch and thermal fuse in the correct position for reliable operation
• Allows the switch to detect door/cover position or user inputs (safe, common symptom: appliance won't start or respond)
• Provides thermal-fuse protection when overheating or overcurrent interrupts normal operation (safe symptom: appliance stops mid-cycle)
• Restores secure electrical connections when the original bracket is cracked or terminals are loose

• Always disconnect power (unplug or shut off breaker) before starting work
• Basic hand tools required; follow the appliance's service manual for exact steps
• Inspect wiring and connectors for heat damage; replace if compromised

Use with motor 357282.

This inlet hose connects the household water supply to the refrigerator's water system so ice makers and dispensers receive a steady water feed. Durable, flexible tubing replaces worn or leaking supply lines to restore proper water flow. What it does:

• Channels incoming water from the home supply to the refrigerator's water valve and ice maker
• Replaces cracked, split, or leaking supply tubing that can cause reduced water flow or puddling
• Helps prevent leaks that can lead to water damage when original tubing fails
• Works with the fridge's internal water system to support ice and dispenser functions

• One inlet hose (single water supply line)

• Turn off the home water supply and unplug the appliance before servicing
• Inspect fittings for signs of corrosion; use the proper connector tools to avoid damage
• Tighten connections to a leak-free fit but avoid over-tightening plastic fittings

Motor mount to gear case.

This wiring clip secures a refrigerator's wire harness to the cabinet or components to prevent chafing and keep wires organized. It helps maintain safe routing and reduces strain on electrical connections. What it does

• Holds wiring harness in place to prevent rubbing against sharp edges or moving parts
• Keeps wires organized to reduce the risk of pinching or accidental disconnection
• Helps prevent intermittent electrical faults caused by loose or strained wiring
• Commonly used near compressor, fan, control box, or rear cabinet areas

• Install by snapping the clip onto the cabinet flange or component and routing the harness through the retainer
• Disconnect power before accessing electrical components or wiring
• Inspect surrounding wiring and insulation; replace any damaged wire or harness tape before reinstalling the clip