Ldf 6920St Parts

The Shaft,Nozzle is an OEM part for LG dishwashers. This part is located inside the dishwasher's spray arm assembly and is responsible for distributing water to the spray arms during the wash cycle.

Causes of failure can be mineral deposits that clog the nozzle openings or flexible shaft deterioration over time.

Symptoms of a bad shaft or nozzle include:

• Inadequate or uneven spray coverage inside the dishwasher
• Dirty dishes, especially on hard to reach areas
• Reduced water pressure during the wash cycle

This OEM LG part is also compatible with some Kenmore models.

This small sleeve bushing supports a pivoting or rotating joint in your dishwasher, providing a smooth bearing surface. Replacing a worn bushing helps restore quiet operation and protects mating parts from further wear. What it does

• Provides a low-friction surface between a shaft/pin and bracket
• Helps maintain proper alignment and reduces wobble at the joint
• Can quiet squeaks or grinding caused by wear
• Replacing a cracked or flattened bushing can improve smooth movement

• 1 bushing

• Disconnect power and shut off water before servicing
• Support the door or component attached to the joint to relieve tension
• Note orientation; transfer any spacers/washers in the same order
• Inspect the mating pin/shaft for wear and replace related parts if damaged

This dishrack tine replaces a damaged or missing row of prongs on your dishwasher rack, restoring secure spacing for plates, lids, and other items so they stay upright throughout the cycle.

• Attaches to the rack to provide prongs that hold dishes upright and separated for effective washing and drying
• Helps prevent items from tipping over or obstructing spray-arm movement
• Common signs it's needed: broken, bent, rusted, or missing tines; flaking coating; dishes not staying in place
• Restores rack organization and usable loading capacity

• Disconnect electrical power and turn off water supply before servicing
• Pull the rack out; release the retaining tabs/clips that hold the tine to the rack
• Remove the damaged tine, align the new tine with the mounting points, and secure it in place
• Ensure the rack slides freely and spray arms spin without interference before running a cycle

This pump casing assembly forms the sealed housing around the pump, channeling water through the system. Replacing a cracked or warped casing helps stop leaks and restore proper water flow and overall pump performance.

• Houses the pump impeller and seals the pump chamber to contain water
• Directs water flow between the tub/sump and the pump for efficient operation
• Helps maintain proper water pressure within the pump circuit
• Common symptoms of a failing casing include leaks near the pump area, weak water movement or poor draining, unusual grinding/rumbling noises, or visible cracks/warping

• Disconnect power and shut off water supply before servicing
• Access the pump (typically from the bottom or rear)
• Transfer any existing O-rings, clamps, and screws as needed; clean sealing surfaces
• Reassemble carefully, reconnect hoses, and run a test cycle to check for leaks

This thermistor holder secures the temperature sensor in place inside the dishwasher, ensuring accurate water temperature readings for proper wash and dry performance.

• Holds the thermistor securely in the sump/tub area
• Helps the control accurately monitor wash water temperature
• A loose or missing holder can cause temperature-related wash issues
• Common symptoms include temperature errors or poor cleaning/drying when the sensor isn't properly positioned

• Disconnect power and turn off water supply before servicing
• Access the sensor location from the tub/sump area; note original orientation
• Transfer the thermistor into the new holder and snap the holder into place
• Inspect the sensor wiring and seals while reassembling

This gasket creates a watertight seal between mating parts in the dishwasher's water system. Replacing a worn or damaged seal helps stop leaks during cycles and maintains proper wash performance. What it does:

• Seals the joint between components such as the sump, pump housing, or inlet assemblies
• Prevents water leakage under pressure during fill, wash, and drain
• Helps maintain spray pressure by reducing internal bypass
• Common symptoms include water on the floor or in the base pan, and a flattened, cracked, or brittle old gasket

• One gasket

• Disconnect power and turn off the water supply before servicing
• Access the gasket location and remove any retaining hardware
• Remove the old gasket and clean both sealing surfaces thoroughly
• Seat the new gasket evenly without twisting; tighten fasteners/clamps uniformly and run a test cycle to check for leaks

This door latch and lock assembly secures the dishwasher door and signals the control that it's safely closed. Replacing a worn latch restores firm door closure, a reliable seal, and consistent cycle operation. What it does:

• Locks the door so cycles can start and continue without interruption
• Helps compress the door gasket for a proper, leak-resistant seal
• Sends a door-closed signal to the control
• Common symptoms: won't start with the door shut, door won't latch or pops open, cycle pauses when jostled, water leaking at the door edge

• One door latch/lock assembly

• Disconnect power at the breaker before servicing
• Remove the inner door panel to access the latch at the top of the door
• Note wire connector positions; move them to the new assembly and secure the latch
• Check latch engagement with the strike and adjust alignment if needed before reassembly

This Rack assembly replaces a worn, damaged, or bent dishwasher rack to restore safe support for dishes and glassware. It returns proper dish spacing and secure loading so items wash evenly and don't shift during cycles. What it does

• Provides the structural frame and tines to hold dishes, glasses and utensils in place during wash cycles.
• Replaces broken or bent rack sections that cause items to tip, nest, or block spray arms.
• Restores proper clearance and alignment so water and detergent reach all items.
• Helps prevent chipping and scratching caused by unstable or collapsed rack areas.

• One complete dishwasher rack assembly as shown.

• High-level replacement: typically slides into existing rack tracks or fastens with a few clips/retainers; verify attachment style for your model.
• Disconnect power and water supply per manufacturer guidance before servicing if appliance access requires it.
• Inspect mounting tracks, rollers and retainers; replace any damaged hardware to ensure smooth rack movement.
• Use care to avoid sharp edges; for model-specific instructions.

This impeller assembly spins on the dishwasher's pump to move water through the system. Replacing a worn or broken impeller restores proper water flow, helping maintain wash performance and reducing noise from the pump area. What it does:

• Moves water through the dishwasher's pump system for circulation and cleaning
• Helps maintain correct water flow and spray pressure to the spray arms
• Typical failure signs: poor cleaning or weak spray, unusual grinding/humming from the sump, or slow/no draining depending on which impeller has failed
• Physical clues include damaged/broken blades or a loose fit on the motor shaft

• 1 impeller assembly

• Disconnect power and turn off the water supply before servicing
• Remove the lower rack and filters to access the pump/sump; follow your model's service information
• Note the impeller's orientation; transfer any reusable seals or hardware from the original as required
• After reassembly, check for leaks and verify the pump spins freely before running a test cycle

This guide assembly is the sliding rail that supports and aligns the freezer drawer. When worn or damaged, it can cause sticking, sagging, or poor sealing; replacing it restores smooth operation and proper drawer closure.

• Supports the freezer drawer and lets it glide smoothly in and out
• Keeps the drawer square and aligned with the front panel
• Helps the drawer close fully to maintain a proper seal
• Common symptoms: drawer hard to open/close, crooked or sagging drawer, grinding/squeaking, frost from incomplete closure, visible rail damage

• Disconnect power before servicing; empty the freezer drawer
• Pull the drawer out, remove the front panel and basket as needed
• Remove mounting screws and the old guide; reuse existing hardware if applicable
• Install the new guide, then verify both sides move evenly and the drawer seals properly

The WATER LEVEL SENSOR ASSEMBLY is an OEM component specifically designed for LG dishwashers. It is an electronic sensor responsible for monitoring and detecting the water level inside the dishwasher tub during each cycle. Precise water level detection allows the dishwasher to optimize water usage and ensure all cycles run as intended. 

Causes of a bad sensor assembly can include the buildup of sediment or minerals on the sensor contacts over time, leading to improper readings. Physical damage from impact could also affect sensor function.

Symptoms of a bad water level sensor assembly include:

• Incomplete or failed wash cycles 
• Error codes related to water issues
• Inability to fill or drain properly
• Flooding or leaks from the dishwasher 

Replace yours today with this genuine OEM LG part to maintain proper dishwasher operation. This OEM LG part is also compatible with Sears/Kenmore.

This component is a sump and motor assembly that is designed to be used on a dishwasher. This part moves the water from the sump collection area up into the spray arms.When the sump and motor assembly is faulty, the dishwasher may leak from the bottom. It is also possible that the dishwasher could run noisily. This high-quality OEM replacement part will fix these problems. If unsure if this part will fix the problems, consult a professional. Disconnect the appliance from the electrical outlet before performing care, maintenance, or replacing any parts on it. Some people performing this replacement may wish to wear work gloves to protect their hands during this process. The replacement process is very easy and takes about 15 to 30 minutes to complete from start to finish.This sump and motor assembly is compatible with dishwashers that are manufactured by LG. It is sold individually and sourced from the manufacturer.

The Micro Switch is an OEM part for LG dishwashers. It plays a crucial role in detecting when the door is securely closed prior to starting a cycle. This important safety feature prevents accidental exposure to hot water, detergent, and chemicals. 

Causes of a bad micro switch include degradation from years of repeated use, debris interfering with mechanisms, or damage from attempts to force or slam the dishwasher door closed.

Symptoms of a bad micro switch include:

• Cycles failing to start despite a closed door
• Hot water or steam visible escaping when running 
• The dishwasher not detecting the closed door position
• Error codes displayed related to door position sensors

This OEM LG part is also compatible with Sears/Kenmore. Replacing only when truly faulty helps ensure safe and reliable dishwasher function.
 

This replacement switch cam interfaces with a lever or knob to actuate a microswitch. It restores reliable on/off signaling and the positive feel/engagement of the related control or latch mechanism when the original cam wears or cracks.

• Translates lever or rotary motion into precise switch activation
• Ensures the switch travels fully to open and close as intended
• A worn or broken cam can cause intermittent operation or functions that won't start/stop as expected
• Helps bring back a defined "click" or detent at the control/lever

• Disconnect power to the appliance before servicing; turn off gas/water if applicable
• Access the switch or latch assembly; remove any knob, trim, or cover as needed
• Note the cam's orientation/indexing before removal; take photos for reference and transfer any springs/clips
• After reassembly, manually test the mechanism to ensure smooth switch actuation before restoring power

This dishwasher sump gasket seals the joint between the sump assembly and the tub to prevent leaks and maintain wash performance. Replace it if the old seal is worn, flattened, cracked, or damaged to stop water escaping beneath the unit.

• Creates a watertight seal where the sump attaches to the tub
• Helps prevent water leaks from the base of the dishwasher
• Supports proper circulation and overall wash performance
• Common failure signs: puddles under the unit, leaks during a cycle, or a visibly torn/deformed gasket

• Disconnect power and turn off the water supply before servicing
• Access the sump from inside the tub (remove lower rack, spray arm, filters, and sump cover) or from below, depending on model
• Clean mating surfaces; install the new gasket evenly without twists or gaps
• Reassemble and run a short cycle to check for leaks

Sump assembly collects and channels a washer's drained water into the drain pump to let the machine empty properly. Replacing a worn or cracked sump helps stop leaks and restores normal draining performance. What it does:

• Directs and funnels tub water to the drain pump so the washer can evacuate water.
• Prevents water from leaking under the washer when intact and properly sealed.
• Can cause poor or no draining, standing water in the tub, or drain/pump-related error codes when damaged.
• May produce unusual noises during the drain cycle if cracked or clogged.

• Disconnect power and turn off water supply before starting any repair.
• Access typically requires removing the washer's front or lower access panel; support the machine as needed.
• Inspect and replace any worn seals, hoses, or clamps when installing to ensure a watertight fit.
• After installation, run a short drain/spin cycle and check for leaks before returning the washer to regular use.