Ldf6920ww Parts

This nozzle guide positions and supports the dishwasher spray nozzle on the rack, helping it align with the rear feed port for reliable water flow to the spray arm and consistent cleaning performance.

• Aligns the rack nozzle with the dishwasher's water feed port
• Stabilizes the nozzle to help ensure steady spray delivery
• If worn or broken, you may notice poor cleaning on the affected rack
• Can also cause intermittent spray or drips at the rear nozzle connection and difficulty engaging the rack nozzle

• Disconnect power and turn off the water supply before servicing
• Pull the rack forward, remove rack end caps/stops, and lift the rack out
• Release the old guide from the nozzle assembly; install the new guide and verify smooth movement and proper alignment with the feed port
• Reinstall the rack, restore power/water, and run a short test to check spray and for leaks

This water guide directs water through the dispenser/ice path so water flows where it should, helping prevent leaks and misdirected dispensing. It's a small molded channel designed to route cold water inside the refrigerator. What it does:

• Guides and channels water from the supply toward the dispenser or ice-making area
• Helps prevent water from dripping into areas it shouldn't and causing puddles
• Supports consistent dispensing by keeping the water path aligned
• Commonly replaced when cracked, warped, or when water is leaking or pooling

• One water guide piece as shown

• Disconnect power and shut off the water supply before replacing
• Remove any interior shelves or panels as needed to access the guide
• Handle carefully to avoid damaging mounting tabs or adjacent seals
• Secure all clips; test dispenser and check for leaks after installation

The Sump and Motor Assembly is an OEM replacement part for LG dishwashers. As a functional pumping component, it circulates water and removes debris during dish cycles.

Symptoms of a bad sump and motor assembly can include:

• Inability to properly fill or drain water from the dishwasher
• Leaks or excessive pooling of water inside the unit 
• Loud knocking or grinding noises from the motor area

Causes of failure may involve a clogged or cracked sump housing impairing flow, or wear of the motor bearings degrading power output over time.

This genuine OEM LG part is also compatible with some select Kenmore brand models.

This check valve is a one-way valve used in the refrigerator's water line. It prevents backflow to maintain pressure for the dispenser and ice maker, helping reduce drips and ensuring consistent water delivery.

• Allows water to flow in one direction only to prevent backflow
• Helps maintain line pressure for steady dispensing and proper ice fills
• May reduce post-dispense dripping at the water outlet
• Failure symptoms can include slow/sputtering dispense, dripping, or inconsistent ice fills

• Unplug the appliance and shut off the household water supply before servicing
• Dispense water to relieve pressure; place a towel to catch residual water
• Note the valve's orientation/flow direction and tubing routing before removal
• Fully seat tubing and secure connections; restore water and check for leaks

This hose connector links internal water lines inside the dishwasher and maintains a secure, leak-resistant seal for proper water flow during each cycle. Replacing a worn connector helps stop leaks and keeps cleaning performance reliable.

• Joins internal water lines/components with a tight, reliable seal
• Helps prevent drips and leaks at a hose connection point
• Supports consistent water circulation through the wash system
• Typical symptoms: puddles under the unit, moisture around the base, visible cracks/swelling at the connector, or a loose fit

• Unplug the dishwasher and turn off the water supply before servicing
• Remove the toe-kick/access panel; place a towel to catch residual water
• Note hose routing and orientation; fully seat the connector and transfer/reuse existing clamps
• After reassembly, run a short cycle and inspect all connections for leaks

This inlet hose routes fresh water into the dishwasher during the fill cycle. Replace a cracked, kinked, or leaking hose to restore proper water flow and help prevent puddles or water damage beneath the unit.

• Routes water into the dishwasher during fill
• Maintains a sealed path to help prevent leaks
• Common fix for leaks under the unit, visible cracks/kinks, or slow/no fill
• Replaces aged, brittle, swollen, or punctured tubing

• Disconnect power and shut off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing the old hose
• Note the original routing; transfer and secure existing clamps/fittings as needed
• Restore water and run a short cycle while checking all connections for leaks

This impeller screw secures the pump impeller so the washer's drain system operates correctly. It's a small but critical fastener that keeps the impeller mounted and aligned for reliable water removal. What it does:

• Holds the pump impeller to the motor or pump shaft to maintain proper rotation
• Prevents the impeller from coming loose or wobbling during operation
• Can help stop grinding or unusual pump noises caused by a loose impeller
• Supports proper draining by keeping the impeller engaged with the pump assembly

• Disconnect power and water before accessing the pump or impeller assembly
• Small part — keep track of screws and use appropriate tools to avoid stripping
• Inspect mating threads and the impeller for wear; replace damaged components as needed

This holder is a small mounting bracket that secures internal components in place, helping reduce movement and noise while keeping parts aligned for reliable operation. It's a direct-fit replacement when the original holder is broken or missing. What it does

• Secures and supports nearby components or assemblies to prevent shifting during operation
• Helps reduce vibration and rattling caused by loose parts
• Maintains proper alignment for connected parts to ensure consistent performance
• Commonly replaced when cracked, warped, or missing after impact or wear

• One holder

• Disconnect power (and water supply if appliance uses water) before servicing
• Inspect surrounding clips and screws; replace any that are damaged
• Typically installs with existing fasteners; keep orientation the same as the original