Ldg3036st Parts

Restore reliable flame performance with this replacement burner. It mixes and distributes gas to produce the cooking flame on your appliance, helping it light consistently and deliver even, controllable heat during everyday use. What it does:

• Directs gas through burner ports to form a controlled cooking flame
• Replaces burners that are cracked, warped, corroded, or clogged
• Can help resolve weak/uneven or yellow flames and delayed ignition
• Restores stable simmer and more even heat distribution

• Includes 1 burner

• Disconnect power and shut off the gas supply; allow the appliance to cool completely
• Access the burner per your model's procedure; remove any grates/caps and retaining hardware if applicable
• Position the new burner over the orifice and igniter; ensure it sits flat and properly aligned
• Reassemble and restore gas/power; test for proper ignition and flame pattern

This power control board is the appliance's main power distribution and control module, restoring proper electrical control so the unit can start and run reliably. It replaces a failed or damaged control board to return normal operation. What it does

• Routes power and control signals to internal components so motors, valves and other systems operate.
• Receives commands from the user interface and provides the control outputs that run cycles and functions — can address unresponsive controls or no-start conditions.
• Regulates and distributes voltage across subsystems to prevent inconsistent or intermittent operation.
• Interfaces with sensors and safety switches to manage cycle behavior and help prevent unsafe operation.

• One power control board.

• Disconnect all power before servicing to avoid shock; verify power is off at the breaker or unplug the appliance.
• Handle the board by its edges and use anti-static precautions to avoid damage to electronic components.
• Note connector orientation and mounting screw locations during removal; transfer any mounting brackets or standoffs to the new board if required.
• Test the appliance after installation and follow the manufacturer's service manual for diagnostic steps.

Replacement nozzle that restores the outlet routing on compatible LG appliances. Installs into the existing mounting location to replace a worn, cracked, or damaged nozzle and helps reduce leaks and misdirected flow. What it does:

• Directs the appliance's outlet flow and helps form a clean seal at the exit point to reduce drips and splashes.
• Commonly replaced when the nozzle is cracked, loose, clogged, or missing.
• Can improve dispensing consistency and reduce misdirected flow or minor leaks.
• Fits into the OEM mounting location.

• Disconnect power and/or water supply before removing panels or working on the appliance.
• Remove any trim or access panels to reach the nozzle; small clips or screws may secure it.
• Handle plastic parts gently to avoid cracking; confirm correct orientation and fit before reassembly.

This gas valve assembly controls gas flow to the appliance's burner, restoring reliable ignition and heating when the original valve fails. It replaces a faulty or leaking valve to help the unit heat safely and consistently. What it does:

• Regulates and routes gas to the burner based on the appliance's control signals
• Prevents gas flow when the appliance is off or during safety shutoff conditions
• Commonly used to address symptoms like no heat, weak heating, or a persistent gas smell when confirmed at the valve
• Works as the appliance's primary gas control component in the fuel delivery system

• One gas valve assembly

• Turn off gas supply and disconnect power before servicing; verify both are isolated
• Inspect all gas fittings and use an approved leak detection method after installation
• Do not modify the part; use proper tools and follow manufacturer service instructions

This gas surface burner head restores even flame and reliable lighting on your range cooktop. Replacing a worn or clogged burner helps bring back proper ignition, flame pattern, and consistent heat output. What it does:

• Directs gas from the orifice through precisely formed ports to create an even ring of flame
• Works with the spark igniter for quick, consistent ignition
• Helps maintain correct flame size and color for efficient cooking
• Typical symptoms include: burner won't light, delayed ignition, weak/uneven flame, or yellow-tipped flames

• Includes 1 burner head

• Disconnect power and shut off the gas supply before servicing
• Remove grate and burner cap; lift off the old burner head and clean the mating surface
• Align the new burner head over the orifice and ensure proper clearance to the igniter
• Reassemble, restore gas/power, and test burner operation and flame pattern

A factory screw for securing specified components in your appliance. Replaces a missing or damaged fastener to restore a tight, reliable hold and help reduce vibration, rattling, and misalignment.

• Secures brackets, covers, or internal assemblies where this exact screw is specified by the manufacturer
• Useful when the original screw is missing, stripped, or corroded
• Helps eliminate looseness, vibration, and rattling noises
• Matches the original fastener for proper fit and thread engagement

• Disconnect power (and shut off water supply if applicable) before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged clips or inserts to ensure a secure repair

This gas valve assembly controls gas flow to the oven and burners so the range heats properly and maintains safe operation. Replace a failed valve to restore ignition and regulated gas delivery. What it does:

• Regulates gas flow to the oven/burner when the appliance calls for heat
• Enables proper ignition and sustained burner/oven flame
• Common symptom: oven or burners won't heat or light even when controls are set
• Can cause clicking or continuous ignition attempts when valve sticks or fails

• Turn off gas supply and unplug the appliance before starting repairs
• Check all fittings for leaks after installation using a soap solution or approved leak detector
• Do not force connections; replace any damaged seals or tubing to ensure safe operation

This tapping screw secures appliance panels, brackets, and trim. Replace a missing or stripped fastener to restore a tight, rattle-free fit and keep components properly aligned.

• Cuts its own threads as it drives (self-tapping) to fasten metal or plastic components securely
• Helps eliminate looseness and vibration noises when an original screw is missing or damaged
• Typical signs you need this part: loose or rattling panels, gaps/misalignment, or covers that won't stay secured
• Direct replacement for the original fastener in the same location

• Disconnect power; turn off water or gas supplies before service
• Start the screw by hand to avoid cross-threading, then tighten with the correct driver
• Align parts fully before tightening and avoid overtightening, especially into plastic
• Reuse any original washers or clips that were installed with the screw

This door gasket is a molded seal that replaces a worn or damaged refrigerator door seal to restore an airtight closure and help maintain proper cooling. It fits on the cabinet door edge to keep cold air in and warm air out. What it does:

• Creates a tight seal around the refrigerator/freezer door to prevent air leaks
• Helps stop frost buildup and uneven temperatures caused by a failing seal
• Reduces cycling frequency and helps the appliance maintain set temperatures
• Common symptoms: visible cracks, gaps, tears, loose edges, interior condensation or frost near the door

• Remove the old gasket completely and clean the mounting surface before installing
• Start installation at the corners, working the gasket evenly into the channel for a uniform fit
• Check alignment and compression around the full perimeter; trim only if the gasket is explicitly manufactured to be shortened
• Follow appliance safety: unplug or disconnect power before beginning work and avoid sharp tools that can tear the new seal

This inlet valve controls water flow into the appliance, restoring proper fill operation and cycle performance. Replaces a failed or leaking valve to stop slow fills, no-fill conditions, or continuous water flow. What it does:

• Opens and closes to allow water into the appliance during fill cycles
• Stops water flow when the fill is complete to prevent overfilling
• Commonly used to address slow fills, no water entering the appliance, or water leaking from the valve area
• Works with the appliance's control system to time and meter water intake

• Disconnect power and shut off the water supply before starting work
• Verify the replacement valve matches the original part number and inlet/outlet fittings
• Use basic hand tools; avoid overtightening fittings to prevent damage

This customized screw secures appliance components where a standard fastener won't fit, helping keep panels, brackets and small assemblies stable. It's a direct-fit replacement when the original specialized screw is missing or damaged. What it does:

• Fastens and holds appliance panels, brackets or small parts in place
• Prevents rattling, loose trim or misaligned components caused by a missing or stripped screw
• Matches the OEM fit and thread pattern for proper engagement and alignment
• Used in locations that require a non-standard or customized fastener

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can strip threads or crack parts
• Keep removed hardware organized so you can reinstall in the original location

Note: This glass is "approximately" 11"tall x 20"wide.

The Grille Assembly is an OEM part for LG cooking ranges and range tops. It provides an additional flat-top cooking surface between the standard burner elements. The grille assembly itself is constructed of heavy-duty materials designed to withstand high heat levels while cooking.

Causes can be wear over time under heavy usage, accidental damage from cookware or cleaning, or failure of the heating elements underneath the plate.

Symptoms of a bad griddle plate include:

• Uneven or slow heating of the surface
• Warping or bending of the plate
• Scratches, cracks, or other surface damage
• Loose or missing mounting hardware

This LG part is also compatible with some Kenmore models.

This Main PCB Assembly is the primary control board that manages a range/oven's functions and user interface, restoring proper control and communication between components when the original board fails. What it does:

• Regulates oven/range functions and timing signals for heating elements and switches
• Powers and communicates with the display, touchpad/buttons, and status indicators
• Helps coordinate safety interlocks and sensor inputs for normal operation
• Commonly replaced for symptoms like unresponsive controls, no display, or intermittent operation

• Disconnect all power at the breaker before accessing the appliance.
• Handle the board carefully to avoid static damage—use ESD precautions where possible.
• Verify power and wiring connections are correct; replace with the exact OEM board only.

This factory-specified fastener secures designated panels and components, restoring a precise fit and helping keep your appliance solid and quiet. Replace a missing, stripped, or rusted original with the correct OEM match for the specified locations.

• Secures brackets, panels, and internal parts where this part number is called out
• Replaces damaged, stripped, corroded, or lost screws
• Helps reduce looseness and vibration that can cause rattling noises
• Exact OEM replacement for positions requiring this specific screw

• Disconnect power and shut off water/gas before servicing
• Match to the removed screw and install only in the locations specified for this part number
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening, especially into plastic
• If multiple screws are involved, start all fasteners before final tightening to ensure alignment

This is a replacement customized screw designed to secure appliance panels and components. It restores proper fit and fastening where the original screw is lost or worn, helping maintain safe, stable operation. What it does

• Replaces missing or damaged mounting screw used on appliance panels and internal components
• Restores secure fastening to reduce vibration and rattling during operation
• Matches the original OEM fit and thread form for correct engagement when verified for your model
• Helps prevent loose parts that can cause noise or interfere with moving components

• Disconnect power and water before servicing the appliance
• Verify screw size, thread direction, and length match the original before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid overtightening to prevent stripping or damaging mating threads