Ldg3036st Parts

Oven door hinge bracket for electric and gas ranges. Secures the door hinge assembly to the frame. Replace if cracked, bent, or broken to restore door support.

This idler bracket mounts the idler pulley or roller in your appliance's tensioning system, keeping a belt or cable aligned and properly tensioned for consistent operation. A bent or worn bracket can cause noise, slippage, or loss of motion.

• Secures the idler pulley/roller in the correct position
• Maintains proper belt/cable tension and alignment
• Helps reduce squealing or squeaking from friction/misalignment
• Can address belts/cables coming off or intermittent movement in the drive mechanism

• Disconnect power; also shut off gas or water before servicing
• Access the tensioner area and note the belt/cable routing and spring orientation
• Relieve tension, remove the old bracket, and transfer the pulley/roller and any spring or hardware as required
• Reinstall the bracket, ensure smooth free movement, route belt/cable correctly, and test operation

Replace your worn or damaged range burner to restore consistent flame and even heat distribution. Directs gas through ports for reliable cooking performance.

Controls gas flow to your range burner. Replace this valve assembly when the original is faulty, leaking, or damaged to restore safe gas regulation.

Fix uneven flames or weak burner heat with this gas range burner orifice. Controls gas flow to burners for proper flame size and cooking performance.

This door gasket is a molded seal that replaces a worn or damaged refrigerator door seal to restore an airtight closure and help maintain proper cooling. It fits on the cabinet door edge to keep cold air in and warm air out. What it does:

• Creates a tight seal around the refrigerator/freezer door to prevent air leaks
• Helps stop frost buildup and uneven temperatures caused by a failing seal
• Reduces cycling frequency and helps the appliance maintain set temperatures
• Common symptoms: visible cracks, gaps, tears, loose edges, interior condensation or frost near the door

• Remove the old gasket completely and clean the mounting surface before installing
• Start installation at the corners, working the gasket evenly into the channel for a uniform fit
• Check alignment and compression around the full perimeter; trim only if the gasket is explicitly manufactured to be shortened
• Follow appliance safety: unplug or disconnect power before beginning work and avoid sharp tools that can tear the new seal

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

This inlet valve controls water flow into the appliance, restoring proper fill operation and cycle performance. Replaces a failed or leaking valve to stop slow fills, no-fill conditions, or continuous water flow. What it does:

• Opens and closes to allow water into the appliance during fill cycles
• Stops water flow when the fill is complete to prevent overfilling
• Commonly used to address slow fills, no water entering the appliance, or water leaking from the valve area
• Works with the appliance's control system to time and meter water intake

• Disconnect power and shut off the water supply before starting work
• Verify the replacement valve matches the original part number and inlet/outlet fittings
• Use basic hand tools; avoid overtightening fittings to prevent damage

Note: This glass is "approximately" 11"tall x 20"wide.

Fix weak or uneven flames on your gas cooktop with this surface burner assembly. Restores consistent heat and proper flame pattern for cooking.

A lower refrigerator kickplate grille that restores proper airflow and the finished look at the base of the appliance. Replaces a cracked, broken, or missing grille to help maintain venting and keep debris out of components. What it does:

• Covers the lower front opening while directing airflow into condenser/vent channels
• Protects internal components from larger debris and accidental contact
• Restores cosmetic appearance when the original grille is cracked, warped, or broken
• Helps maintain proper airflow patterns that support cooling performance

• One grille assembly

• Disconnect power to the appliance before beginning any work
• Typically installs with clips and/or screws at the base; use basic hand tools
• Handle the grille carefully to avoid snapping plastic tabs during removal or installation

Oven door hinge assembly for gas ranges. Mounts to the oven cavity and door frame to support smooth opening and closing. Replace if cracked or worn.

Wire harness for gas ranges and wall ovens. Connects electrical components within the appliance. Replace if wires are frayed, damaged, or connections are loose.