Lesa907pbl02 Parts

This high-temperature insulation is used in the oven assembly to contain heat and protect nearby components and cabinetry. Replacing damaged insulation helps the appliance maintain set temperatures and keeps exterior surfaces from getting excessively hot. What it does:

• Helps retain heat for stable baking and roasting temperatures
• Reduces heat transfer to the appliance frame and adjacent cabinets
• Replaces insulation that is torn, charred, or saturated with spills/grease

• One insulation piece

• Disconnect power; for gas models, also shut off the gas supply
• Remove the range or wall oven and access the oven body
• Wear gloves, eye protection, long sleeves, and a dust mask; fibers can irritate skin and lungs
• Reinstall in the same orientation/routing as the original; do not compress insulation or block vents

A replacement brake pad kit that restores the washer's ability to slow and stop the tub safely and reliably. Replacing worn pads helps reduce noise and prevents extended spin-down times. What it does:

• Replaces worn brake lining that lets the brake engage and stop the tub
• Helps reduce scraping, grinding, or metal-on-metal noises from the brake area
• Addresses slow or incomplete tub stop after a spin cycle
• Works as a direct-fit service kit for compatible Speed Queen transmissions/brakes

• Disconnect power and follow the manufacturer's service manual before starting
• Requires basic hand tools and access to the brake/transmission area; a lift or service jack may be needed for some models
• Inspect related brake hardware and mounting surfaces; replace damaged components as needed
• Do not operate the machine with covers removed or without confirming correct brake operation after installation

Black

A single replacement mounting screw used to secure appliance panels and components. Restores proper fit and prevents rattling or loose parts so trims and panels stay aligned during normal use. What it does:

• Fastens panels, brackets or trim pieces to the appliance frame
• Replaces worn, stripped or missing screws that cause loose or rattling parts
• Helps restore secure alignment for doors and access panels
• Works where the OEM lists a basic machine/fastener screw

• Disconnect power and water before beginning any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Thread by hand to start, then tighten until snug—do not overtighten
• Keep small parts away from children and pets during installation

This flat metal washer provides a durable spacer and load-distributing surface for a matching fastener, helping secure assemblies and reduce wear. It's a small but essential hardware piece for routine repairs and reassembly. What it does:

• Distributes fastening load to protect softer materials and prevent pull-through
• Creates a smooth bearing surface for nuts and bolts to seat evenly
• Helps reduce vibration and loosening in moving assemblies
• Commonly used on panels, brackets, and mounting hardware where a flush fit is needed

• One flat metal washer as shown

• Disconnect power and water (if applicable) and access the assembly before replacing hardware
• Use the matching bolt/nut size and washer ID/OD for correct fit; do not force oversized fasteners
• Hand-start fasteners to avoid cross-threading, then tighten to the equipment manufacturer's spec
• Keep small parts secure during disassembly to avoid loss or damage

This bracket is the mounting base for the dryer's cylinder support roller. Replacing a bent or worn bracket restores proper roller alignment so the drum turns smoothly, reducing vibration and noise and preventing premature wear.

• Provides the fixed mount for the cylinder support roller
• Maintains drum alignment for smooth, even rotation
• Replace if the bracket is bent, cracked, or mounting holes are elongated
• Common symptoms of a failing bracket: loud rumbling/thumping, scraping, excessive vibration, or visible roller misalignment

• Disconnect power; for gas models, also shut off gas supply
• Access the roller area per your model's service information and support the drum
• Transfer the roller/axle and spacers from the old bracket; install the new bracket in the same orientation
• Verify the roller spins freely and hand-rotate the drum to check for binding before test run

This gas valve assembly controls gas flow to the burner's ignition system, restoring proper ignition and heat delivery when the valve fails. Direct-fit replacement designed for the appliance's factory gas valve location. What it does:

• Regulates gas flow to the burner so the dryer can ignite and heat properly
• Replaces a worn or stuck valve that can cause no-heat or intermittent heating
• Works with the appliance's ignition system to open and close the gas pathway as needed
• Helps resolve failures where the burner does not light despite proper power and gas supply

• Turn off and shut off both electrical power and the gas supply before starting work
• Gas connections should be tightened and tested for leaks
• Follow the appliance manufacturer's service instructions when installing and testing
• Do not modify the part; use only as a direct replacement

This water inlet tube routes household water from the supply to the fridge's internal water system, helping deliver water to the dispenser and ice maker without leaks. Durable tubing replaces cracked or kinked lines to restore proper flow. What it does:

• Directs water from the supply valve to the refrigerator's internal water components.
• Replaces cracked, split, or kinked tubing that can cause leaks or low flow.
• Helps restore water flow to the dispenser and ice maker when the original line is damaged.
• Provides a secure, leak-resistant path when installed with proper fittings or clamps.

• One water inlet tube.

• Always disconnect power and shut off the water supply before replacing the tube.
• Drain and relieve pressure from the water line before disconnecting fittings to avoid spills.
• Use the correct OEM clamps or fittings and inspect connectors for wear; replace clamps if damaged.
• Tighten fittings securely but avoid over-tightening plastic fittings to prevent cracking.

This left-side meat pan rail block secures the meat pan/drawer slide in place so the drawer opens and closes smoothly. It replaces a worn or broken support to restore proper alignment and prevent the drawer from sagging or catching. What it does:

• Supports the left end of the meat pan/crisper drawer rail for stable sliding action
• Prevents the drawer from tilting, binding, or falling out when loading
• Replaces cracked, worn, or missing blocks that cause noisy or uneven drawer movement
• Keeps the drawer aligned for proper sealing and reliable operation

• Disconnect power to the appliance before servicing to avoid injury.
• Remove the meat pan/drawer per the appliance guide to access the rail block.
• Snap or screw the block into the rail per OEM alignment; do not force parts.
• If hardware is damaged or additional guides are worn, inspect adjacent components and replace as needed.

Left side.

This temperature control thermostat replaces the refrigerator's manual/mechanical control that cycles the compressor and fans to maintain set temperatures, helping restore consistent cooling. Simple, direct replacement for units using this style of controller. What it does:

• Opens and closes the cooling circuit based on the temperature setting to regulate cabinet temperature
• Stops continuous running when the compressor fails to cycle or restarts cooling when the temperature rises
• Commonly used when the refrigerator won't reach or hold set temperatures or runs constantly
• Compatible with systems that use a mechanical dial-style temperature control and capillary sensing tube

• Disconnect power before servicing to avoid shock or injury
• Replace the thermostat in the same orientation and secure sensing tube without kinks; handle the capillary tube carefully
• Verify electrical connections match the original and restore power only after mounting is complete
• If temperature issues persist after replacement, check related components (evaporator, defrost, compressor)

This micro switch detects door or lid position and tells the appliance when the door is closed so cycles can start or safety interlocks stay engaged. It restores reliable door sensing and helps prevent operation with the door open. What it does:

• Acts as a position sensor that completes or breaks the control circuit when the door/lid is closed or opened
• Keeps the appliance from starting or continuing a cycle if the door is open (safety interlock)
• Common symptom fix: appliance won't start, stops mid-cycle, or shows door-related error codes
• Small electrical switch designed to mount at the door latch or frame and connect to the appliance wiring harness

• Disconnect power (unplug or shut off breaker) before attempting service
• Access may require removing panels, trim, or the door latch assembly; keep track of screws and fasteners
• Observe wiring orientation and connector positions; replace exactly as removed or tag wires

This condenser coil assembly removes heat from the refrigerant so your refrigerator can maintain proper cooling. Replacing a damaged or clogged condenser restores heat rejection and helps the compressor run more efficiently. What it does

• Transfers heat from the refrigerant to the surrounding air so the system can cool interior compartments
• Helps prevent the compressor from running continuously by allowing proper heat dissipation
• Commonly fails when fins are bent, clogged with debris, or corroded, causing reduced cooling performance
• Can cause the refrigerator to run hot, overheat at the rear, or cycle abnormally when compromised

• One condenser coil assembly

• Disconnect power to the appliance before starting any repair
• Replacement typically requires removal of lower rear access panels and panel fasteners; keep hardware for reinstallation
• Handle the coil carefully to avoid bending fins or damaging tubing

This right-hand white panel end replaces a damaged or worn side cap to restore the washer's appearance and keep the cabinet edge protected. It fits the machine's front panel area and matches factory styling. What it does:

• Covers and protects the right-hand side edge of the front cabinet or console
• Restores the unit's finished appearance after damage, scratches, or missing trim
• Helps prevent exposure of internal edges and wiring along the cabinet side
• Matches factory color and mounting locations for a clean replacement

• Remove power and disconnect the appliance before beginning any repair.
• Minor disassembly of the front panel or console may be required to access mounting tabs.
• Handle edges carefully to avoid cutting yourself or scratching the finish.
• Replace missing or damaged fasteners with matching hardware for secure fit.

This timer knob assembly is the replacement control knob that lets you set and adjust cycle time on the dryer/washing machine control. It restores a secure grip and clear cycle selection so you can operate the machine easily. What it does:

• Provides a firm, easy-to-turn control for selecting timer settings and cycles
• Replaces cracked, stripped, or missing knobs that are hard to turn or won't stay set
• Helps ensure the timer/control shaft is engaged for accurate cycle selection
• Matches OEM fit and function for a direct replacement when the knob is worn or damaged

• Disconnect power to the appliance before attempting replacement
• Knob typically pulls straight off the control shaft; align splines and press on until seated
• If a retaining clip or screw is present, remove and reinstall as needed—retain hardware
• Do not force the knob; confirm proper alignment to avoid damaging the control shaft