Lfbd409lboa Parts

This bezel is a trim piece for Frigidaire dishwashers that finishes and protects an opening on the door/control panel, helping the mating component sit properly while restoring a clean, factory look.

• Frames and protects the panel opening for a control or latch component
• Helps keep the mating part aligned and seated correctly
• Covers raw edges and gaps to reduce wear and debris buildup
• Common symptoms: broken or missing trim, loose/wobbly bezel, cracked retaining tabs, cosmetic damage

• Disconnect power to the dishwasher before servicing
• Remove the control knob or latch handle to access the bezel
• Release the bezel's retaining tabs/clips and lift it out from the panel
• Align the new bezel and snap/secure it into place; reinstall any removed parts and test operation

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

Factory replacement dishwasher cover that shields internal components. Installs to restore a secure, finished appearance. Replace if cracked, missing, or loose.

Protective shield that guards internal dishwasher components from heat and moisture. Replaces cracked, warped, or missing original shields.

This cup shelf is a direct-fit refrigerator door bin that restores secure storage for cups, bottles and small containers. It replaces a cracked, warped or missing shelf so items stay organized and won't shift on the door. What it does:

• Provides a stable ledge for cups, bottles and small containers on the refrigerator door
• Replaces damaged or cracked door shelving that can no longer support items
• Helps prevent spills and items sliding or falling when the door is opened or closed
• Matches the original shelf shape to maintain proper fit and alignment

• Basic snap-in/screw-in installation; your model's door assembly instructions
• Remove power to the appliance or work with the door empty for safe handling
• Handle carefully to avoid chipping; wear gloves if edges are sharp
• If fasteners are present, reuse original screws/clips or replace with OEM equivalents

This refrigerator door gasket creates a tight seal around the door to help maintain proper cooling and energy efficiency. It replaces a worn or damaged rubber seal to reduce air leaks and frost buildup. What it does:

• Seals the door perimeter to keep cold air in and warm air out
• Helps prevent frost and moisture buildup inside the compartment
• Supports consistent temperatures for food safety and performance
• Can reduce excessive run time and energy use caused by leaks

• Unplug the appliance or disconnect power before servicing
• Remove the old gasket and clean the gasket channel before installing the new seal
• Warm the gasket slightly if needed to ease installation and ensure proper fit
• After installation, allow time for the gasket to form to the door; check the seal and adjust as needed

Replacement mounting screw for dishwashers. Secures components and panels inside your dishwasher. Order a new screw if yours is stripped, missing, or damaged.

Sound dampening insulation for your dishwasher. Reduces noise during operation. Replace if worn, torn, or missing to restore quiet performance.

This door gasket is the flexible rubber seal that closes the refrigerator door, helping keep cold air in and reduce energy loss. Replacing a worn or torn gasket restores a tight seal and helps the appliance maintain proper temperature. What it does:

• Seals the cabinet to keep cold air inside and warm air out
• Helps maintain consistent fridge/freezer temperature and efficiency
• Reduces frosting and moisture buildup caused by leaks
• Commonly needed when the seal is cracked, torn, warped, or no longer mates flush with the cabinet

• One replacement door gasket

• Clean the door flange and gasket mounting area before installing to ensure a proper seal
• Inspect for mounting clips or retainer channel; follow appliance-specific alignment steps for a snug fit
• Warm the gasket slightly (per OEM guidance) if needed to ease installation — avoid open flames or excessive heat

Replacement mounting screw for dishwasher panels, brackets, and trim. Secures loose components caused by missing, stripped, or damaged fasteners.

Replacement outer door panel for your dishwasher. Installs on the exterior door frame. Order when your original panel is dented, bent, or damaged.

Complete dishwasher door assembly panel. Replaces cracked, dented, warped, or cosmetically damaged outer door panels. Restores appearance and structural integrity.

Mounting screw for dishwasher assembly. Secures internal components and panels. Replace if missing, stripped, or corroded during maintenance or repair.

Replace your cracked or missing dishwasher kickplate toe panel. This durable trim covers the lower front base, protecting against scuffs and restoring a clean appearance.

Secures dishwasher wire harness and prevents moisture from reaching the dispenser assembly. Replace if cracked, loose, or causing electrical issues.