Lfc22770sb/01 Parts

Small stopper that fits inside the handle assembly to limit travel and keep the handle properly seated. Replace if worn, missing, or broken to restore secure feel.

Door hinge screws secure the refrigerator door hinges to the cabinet frame, allowing proper door operation and alignment. Replace when doors sag, don't close properly, or screws are loose, stripped, or missing causing door misalignment.

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

This is a left-side drawer slide rail assembly that guides the freezer drawer in and out of the refrigerator. It mounts inside the freezer compartment and allows smooth, stable opening and closing of the pull-out drawer. Replace this rail if the freezer drawer is difficult to slide, feels uneven, sticks, or has come off its track.

Rattling or loose parts in your refrigerator? This retaining pin secures moving components and keeps them aligned for smooth, quiet operation.

This main PCB power control board assembly controls power distribution and electronic functions for the appliance's control system, providing a direct replacement to address control failures and restore normal operation. What it does:

• Manages power and control signals for the appliance's electronics and control panel
• Can cause an unresponsive control panel or display errors when faulty
• Replaces the primary control board to resolve electronic/communication failures

• Always disconnect power to the appliance before attempting replacement.
• Handle the board as an electrostatic-sensitive device; avoid touching components or connectors.
• Verify the part number and match mounting/connector orientation before installing.

Replacement rail holder that secures sliding rails in your refrigerator. Installs on the frame to restore alignment. Needed when cracked or broken.

This door holder secures the microwave door assembly to the cabinet, restoring proper alignment and a snug close. Replace a broken or worn plastic retainer to reduce rattling and help the door seat correctly. What it does:

• Secures the door assembly to the oven frame so the door sits flush and aligned
• Helps the door engage the latch correctly for reliable closing
• Reduces door movement and rattling caused by a cracked or missing retainer
• Commonly replaced when the door feels loose, sags, or won't stay properly seated

• One door holder

• Disconnect power before starting work; never service a microwave while it's energized
• Remove door trim and glass panels carefully to avoid damage; keep track of small screws and clips
• Test door alignment and smooth operation after installation; do not force parts into place

This is a small retainer clip that secures the compressor in place at the base of the refrigerator. It helps prevent the compressor from shifting or vibrating excessively during operation. Replace this clip if your refrigerator produces unusual rattling or vibrating noises from the back, or if the compressor appears loose or has shifted from its mounting position.

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

Refrigerator lamp light cover assembly protects the interior bulb and sensor. Replace if cracked, discolored, or broken to restore proper lighting.

Secure refrigerator panels, brackets, and internal components with this replacement mounting screw. Ideal for missing, stripped, or damaged fasteners.

Left-hand drawer rail guide assembly for refrigerator bottom compartment. Replace when cracked, broken, or causing drawer misalignment or rough sliding.