Lfc25570 Parts

This hinge cover fits over the door hinge to conceal and protect the mechanism. Replacing a cracked or missing cover restores a clean, finished look and helps keep hinge components shielded from dust, snags, and everyday wear.

• Conceals the door hinge for a finished, factory look
• Helps protect hinge hardware from dust and accidental contact
• Reduces snag points around the hinge area
• Typical failure signs: cracked plastic, broken tabs, missing cover, or a cover that won't stay attached

• Disconnect power before servicing; hinge areas can contain wiring
• Open the door and remove any retaining screw(s) or release the cover's tabs
• Lift off the old cover; align and snap or screw the new cover into place
• The door opens and closes freely with the cover installed

A replacement door gasket assembly that seals the refrigerator door to help maintain internal temperature and reduce energy loss. Restores a proper door seal to help keep food fresher and reduce cooling strain. What it does:

• Forms a tight seal around the refrigerator door to minimize cold-air loss and help maintain set temperatures.
• Helps prevent frost buildup and condensation inside the fresh-food compartment when the seal is compromised.
• Can reduce cycling frequency and excessive run time caused by a damaged or worn door seal.
• Common symptoms of a failing gasket: visible gaps, cold spots, frost or ice buildup, or condensation on the door edges.

• Disconnect power to the appliance before starting any repair.
• Remove food and door-mounted items as needed for safe access and handling.
• Align the gasket into the door channel, working it evenly around the perimeter so it seats fully; some distortion may correct after a short run time.

This bracket holder assembly is a structural mount used to secure an internal component, keeping it properly positioned during operation. Replacing a cracked or loose bracket restores support and helps prevent vibration, rattling, and misalignment.

• Provides a fixed mounting point to hold the supported part in place
• Maintains alignment to reduce vibration, rubbing, or noise
• Helps prevent shifting that can lead to premature wear
• Common symptoms: broken tabs or cracks, loose/misaligned component, rattling noises, visible damage to the old bracket

• Disconnect power; shut off water or gas if applicable
• Note screw locations and orientation; take a photo before removal
• Transfer any reusable clips or hardware from the old bracket
• Tighten fasteners evenly and avoid over-tightening to prevent damage

This replacement door gasket creates a tight seal around the refrigerator door to help keep cold air in and warm, moist air out. Restores proper sealing to help maintain temperature and reduce frost or moisture buildup. What it does:

• Seals the refrigerator door to maintain consistent internal temperatures
• Helps prevent moisture, frost, and condensation inside the fresh-food compartment
• Reduces air leaks that can cause the fridge to run more frequently or uneven cooling
• Common symptom: visible gaps, torn or compressed seal, or moisture/frost near the door edge

• Disconnect power to the appliance before starting any work.
• Remove the old gasket carefully; inspect and clean the gasket channel and mating surface before installing the new seal.
• Warm the gasket slightly or work around the perimeter to seat it evenly; avoid overstretching.
• If clips or adhesive are used on your model, reuse or replace only the exact fasteners specified by the manufacturer.

This refrigerator sheath heater melts frost from the evaporator so air can circulate freely and the unit can cool properly. Replacing a failed heater helps restore even temperatures and reduce frost buildup in the freezer.

• Warms the evaporator coil during defrost cycles to clear ice
• Helps prevent restricted airflow, warm spots, and long run times
• Common failure symptoms include heavy frost on the evaporator, poor cooling, ice buildup on the back panel, or frequent defrost errors
• May cause sizzling sounds or water under the evaporator area during normal operation after replacement

• Unplug the refrigerator before service; defrost any heavy ice to access parts safely
• Access typically from the rear of the freezer compartment behind the evaporator cover
• Handle heater leads and evaporator fins carefully to avoid damage
• Secure all connectors before reassembly

This connector secures and transmits motion between the drawer drive and the sliding assembly, restoring smooth drawer movement and alignment. It's a direct-fit replacement that helps fix sticking, slipping, or non-moving drawers. What it does:

• Couples the drawer drive mechanism to the sliding gear, allowing the drawer to open and close reliably
• Replaces worn or broken connector teeth or mounts that cause skipping or jammed operation
• Helps correct uneven or noisy drawer movement caused by damaged linkage
• Restores proper engagement so the drawer responds to normal open/close controls

• One connector as shown

• Disconnect power to the appliance before servicing to avoid electrical shock or injury
• Inspect surrounding gears, tracks, and mounting points; replace any damaged parts for best results
• Basic hand tools are typically required; handle plastic gears carefully to avoid further damage

This dispenser lever is the replacement actuator that presses the ice/water switch so your refrigerator dispenses on demand. Restores proper contact and smooth push action for reliable dispensing. What it does

• Acts as the user-facing lever you press to activate the ice or water dispenser
• Re-establishes firm, consistent contact with the dispenser switch when the original lever is cracked, loose, or broken
• Stops intermittent dispensing caused by a worn or misaligned actuator
• Matches the OEM shape for correct alignment and smooth operation

• Turn off power to the refrigerator or unplug it before starting work
• Most installations are screw- or snap-style; remove the dispenser bezel to access the lever
• Handle plastic components gently to avoid cracking; use trim tools if needed

A momentary push-button switch that restores reliable button control on the appliance console. Replaces a worn or non-responsive push switch so the control board receives a clear input when the button is pressed. What it does:

• Sends a momentary electrical signal to the control board when pressed
• Replaces broken, stuck, or intermittently working push buttons
• Helps resolve symptoms like no response from the console, intermittent button function, or a physically damaged button
• Functions as the user input for single-press commands

• One momentary push switch

• Disconnect power before servicing to avoid shock or injury
• Access usually requires removing the control panel or console; use appropriate screwdrivers
• Note connector orientation and gently unplug wire harness—do not pull on wires

This center hinge assembly replaces the refrigerator door center hinge to restore proper door alignment and smooth operation. It supports the door weight and helps maintain correct sealing for reliable cooling performance. What it does:

• Supports the center of the door, keeping it aligned and preventing sagging
• Provides the pivot point for smooth opening and closing
• Helps maintain a consistent door seal to prevent cool-air loss
• Can eliminate shifting, squeaking, or uneven door gaps caused by a worn hinge

• 1 center hinge assembly

• Disconnect power and empty or support the door before removing the hinge
• Use appropriate tools and a second person to safely support the door during replacement
• Inspect adjoining hinges and mounting hardware; replace any damaged fasteners for best results

The Leveling Leg is an OEM part for LG refrigerators. It is one of the four legs at the bottom corners that elevate and provide stability to the entire appliance.

Causes of failure can be broken mounting points that no longer provide secure elevation, full compression of the built-in cushioning, or damage from impact on an unlevel floor.

Symptoms of a faulty leveling leg include:

• Excessive shaking or vibrating of the refrigerator
• Door alignment issues where doors are difficult to open or close fully
• Visible leaning or misalignment of the refrigerator cabinet

This OEM LG part is also compatible with some Kenmore models.

This cover cap is a small plastic trim piece that protects exposed fasteners and improves the appliance's appearance. It snaps into place to hide mounting posts and help prevent snags or debris buildup. What it does:

• Covers and protects exposed screws, posts, or fasteners for a finished look
• Prevents lint, dust, and debris from collecting around the mounting point
• Reduces the chance of fabric snags or contact with sharp edges
• Restores worn or missing trim for improved cosmetics

• Disconnect power to the appliance before starting any service that exposes electrical components
• Usually installs by snapping over the post or press-fitting into the trim opening — no special tools required
• If needed, remove adjacent trim pieces to gain access, then reinstall trim in reverse order
• Inspect surrounding mounting hardware for damage and replace if necessary

This replacement door gasket assembly seals the refrigerator door to help maintain proper temperature and reduce energy loss. It restores the seal around the door edge for better cooling performance and food preservation. What it does:

• Creates an airtight seal around the refrigerator door to limit cold air escape
• Helps maintain consistent internal temperature for food safety
• Reduces frost buildup and excessive compressor run time when working properly
• Addresses symptoms such as warm spots near the door, visible gaps, or persistent condensation

• One door gasket assembly

• Inspect the door and mounting channel for debris before installing; clean with mild detergent and dry completely
• Gasket typically stretches into a channel and secures around the door perimeter—avoid sharp tools that can damage the seal
• For best results, install at room temperature; warm the gasket gently if needed to ease fitting

This replacement screw fastens appliance panels and components to maintain proper alignment and quiet operation. Use it to replace missing or worn screws that cause loose trim, rattling, or parts that won't stay secured. What it does:

• Secures panels, brackets, or trim to restore proper fit and reduce vibration noise
• Replaces missing or stripped screws that cause loose or wobbly components
• Helps maintain electrical and mechanical connections by keeping parts properly seated
• Small, discrete fastener commonly used in interior and exterior appliance assemblies

• Screw

• Disconnect power before accessing interior components to avoid shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• Keep track of removed fasteners and replace like-for-like for proper fit

This grille cover protects the appliance's cooling/ventilation fan and helps direct airflow where it's needed. It restores the cabinet finish and keeps debris away from the fan housing for more reliable operation. What it does:

• Shields the fan from loose debris and small objects that can cause damage
• Helps channel airflow for proper cooling/ventilation
• Prevents direct contact with fan blades for improved safety
• Reduces rattling or vibration caused by damaged or missing grille

• Disconnect power to the appliance before beginning any work
• Remove any trim or access panels as required to reach the fan area
• Secure with the factory fasteners; do not overtighten to avoid cracking
• Handle edges carefully; wear gloves if needed and test operation after reassembly