Lfx259600 Parts

RAIL,SLIDE-RIGHT

The Compressor Overload Protector is an OEM replacement part for LG refrigerators. It plays an important safety role in protecting the compressor from damage due to excessive heat. Located near the compressor unit, the overload protector functions to shut off power to the compressor if temperatures become too high during operation.

Causes can include normal wear over time rendering it less responsive to temperature changes. Mineral or refrigerant deposits may also impede its ability to detect overheating conditions accurately.

Symptoms of a faulty overload protector include:

• Refrigerator fails to properly cool or the compressor does not run
• Circuit board or electrical component failure or burnout
• Lack of cold air production and higher than normal freezer/fridge temperatures

This OEM LG part is also compatible with some Sears/Kenmore models.

The Drawer Guide is an OEM part for LG refrigerators. This part allows the smooth and effortless operation of the refrigerator's drawers, ensuring they glide in and out with ease. 

Causes of a bad drawer guide can be attributed to wear and tear over time, misalignment during installation, or damage from excessive force or improper use of the drawers.

Symptoms of a bad drawer guide include:

• Difficulty opening or closing the drawers
• Drawers getting stuck or not sliding properly
• Excessive friction or resistance when operating the drawers
• Drawers becoming misaligned or tilted
• Unusual noises or grinding sounds when using the drawers

This OEM LG part is also compatible with some Kenmore models.

This hinge lever mounts on the refrigerator door hinge to guide door movement and closure, helping the door seal properly. Replacing a worn or broken lever restores smooth operation and consistent sealing.

• Guides hinge motion so the door opens and closes smoothly
• Helps maintain door alignment for a reliable gasket seal
• Replace if the lever is visibly cracked, worn, or deformed

• Disconnect power and support the door to prevent injury or damage
• Remove the hinge cover and fasteners; note the lever's orientation before removal
• Install the new lever in the same position and reassemble the hinge components
• Adjust hinge per model procedures if needed

This condenser fan assembly circulates air across the condenser coils and compressor to remove heat from the refrigeration system. Replacing a failing fan helps restore efficient cooling performance and protects the compressor from overheating. What it does:

• Draws air through the condenser coils to dissipate heat
• Supports proper system pressures and overall cooling efficiency
• Helps maintain stable temperatures in both compartments
• Common symptoms include the fan not running, loud noise from the rear, warm cabinet temperatures, or a very hot compressor area

• Pre-assembled fan motor with blade and mounting bracket

• Disconnect power before servicing; use gloves to protect against sharp edges
• Access the lower rear compartment and remove the back cover to reach the fan
• Note wire positions; move over any reusable grommets or screws and secure the assembly firmly
• The blade spins freely and is oriented to move air across the condenser; clean coils before restoring power

The Freezer Drawer Gear is an OEM part for LG refrigerators. It facilitates the smooth operation of the freezer drawer, allowing it to slide in and out effortlessly.

You should replace this gear if it becomes worn or damaged. Causes of a bad freezer drawer gear can include regular wear and tear, damage from overloading the drawer, or mechanical issues due to improper alignment or installation.

Symptoms of a bad freezer drawer gear include:

• Difficulty in opening or closing the freezer drawer
• The drawer not staying aligned or level
• Unusual noises when operating the drawer

This OEM LG part is also compatible with Sears/Kenmore.

RAIL,SLIDE-LEFT

The Screw is an OEM part for LG refrigerators. This part secures the shelf brackets within the refrigerator compartment.

Causes of a bad Screw can range from physical damage or impact to general wear and tear over time. 

Symptoms of a faulty Screw  include:

• Shelves feeling loose or unstable
• Shelves sagging or not sitting level
• Shelves falling out or collapsing when loaded with items

This OEM LG part is also compatible with some Kenmore models.

This small torsion spring restores tension to the dispenser ice door lever so the chute door snaps closed after dispensing. It helps keep warm air and moisture out, reducing frost, condensation, and stray ice from the dispenser.

• Provides return tension for the dispenser ice chute door/lever
• Helps the chute door seal properly to limit warm air infiltration
• Worn or broken springs may cause the ice door to stay open or close slowly
• Symptoms can include frost/ice buildup in the chute, moisture at the dispenser, or cubes dropping/clumping

• Unplug the refrigerator or switch off the circuit breaker before servicing
• Remove the dispenser trim/panel to access the ice door mechanism; note spring orientation with a photo
• Use needle-nose pliers and eye protection—small springs are under tension and can snap
• After installation, cycle the dispenser to confirm the door opens/closes freely and seals

THERMISTOR ASSEMBLY,PTC

This plastic tube carries water within your refrigerator between internal components. Replacing a brittle, kinked, or leaking line restores dependable water flow and helps prevent drips that can damage interiors, cabinetry, or floors. What it does

• Routes water between internal components (such as valves, filters, reservoirs, and dispensers)
• Helps maintain proper water flow and pressure when intact and unkinked
• Typical failure symptoms: water leaks, slow or no water flow, visible cracks, flattening, or kinks
• Age- or heat-related hardening can cause stress cracks near bends or fittings

• One plastic tube

• Unplug the refrigerator and shut off the water supply before servicing
• Note original routing and clip locations; avoid sharp bends, abrasion points, and hot surfaces
• Insert tube ends fully into their fittings (quick-connect or compression, per design) and gently tug to confirm they're seated
• Restore water, purge air as needed, and check all joints for leaks before pushing the unit back

This fan motor assembly circulates air across the evaporator coils to keep temperatures even inside the refrigerator. Replacing a worn or noisy motor restores proper airflow for consistent cooling performance.

• Drives the evaporator fan to move chilled air through the cabinet and vents
• Helps maintain stable temperatures and reduces frost from stagnant air
• Common symptoms: weak or no airflow, loud or intermittent fan noise, temperature fluctuations, refrigerator section warmer than expected
• Failures may result from worn bearings, moisture exposure, or an open motor winding

• Disconnect power before servicing; wear cut-resistant gloves and eye protection
• Access the fan behind the interior rear panel; remove shelves/drawers as needed and avoid bending evaporator fins
• Note wire connector orientation and mounting order; transfer any reusable hardware from the original assembly as needed
• After reassembly, verify the fan spins freely and confirm operation before reloading the compartment

This dispenser lever holder is the mounting bracket behind the refrigerator's dispenser paddle. It supports and aligns the lever and switch so water or ice dispenses reliably when the paddle is pressed.

• Holds and guides the dispenser lever and actuator switch inside the dispenser housing
• Provides a secure pivot point for smooth paddle movement
• Helps ensure consistent activation of water and ice dispensing
• Damage can cause a loose or stuck paddle, intermittent dispensing, or no dispense

• Disconnect power and shut off the water supply before servicing
• Remove the dispenser panel/escutcheon to access the lever assembly; note part orientation
• Transfer the lever, switch, and return spring to the new holder and secure with the original fasteners
• Restore power/water and test dispensing before reinstalling trim

The Cap Cover is an OEM part for LG refrigerators. This cover is designed to protect and secure various components within the refrigerator, such as the water filter or other internal mechanisms. Its role is to ensure that these components are shielded from debris, moisture, and potential damage, maintaining the overall efficiency and cleanliness of the appliance.

Causes of a bad cap cover can include wear and tear over time, cracks or breaks from accidental impacts, or warping due to exposure to temperature fluctuations. Misalignment or improper installation can also contribute to the cap cover becoming damaged or ineffective.

Symptoms of a bad cap cover include:

• Loose or missing cover
• Visible cracks or damage on the cover
• Debris or moisture accumulating in areas meant to be protected
• Misalignment or difficulty in securing the cover properly

This OEM LG part is also compatible with Sears/Kenmore.

Left Hand side