Lfx31925st Parts

The Drier Assembly is an OEM part for LG refrigerators. This part is responsible for removing moisture and contaminants from the refrigerant. This ensures that the refrigerant circulates effectively and efficiently, preventing damage to other components and maintaining the refrigerator's cooling performance.

Causes of a bad Drier Assembly can include contamination from moisture entering the refrigerant lines, blockages from debris or particulates, and general wear and tear over time that reduces its effectiveness.

Symptoms of a bad Drier Assembly include:

• Reduced cooling efficiency or warm refrigerator temperatures
• Unusual noises from the refrigeration system
• The compressor running continuously or cycling frequently
• Frost buildup on the evaporator coils due to improper refrigerant flow

This OEM LG part is also compatible with Sears/Kenmore models.

The Ice Dispenser Door Lever is an OEM part for LG refrigerators. This part is responsible for operating the ice dispenser door, allowing ice to be dispensed from the ice maker when the lever is pressed.

Causes of a bad part can include mechanical wear and tear from repeated use, physical damage or impact, or issues with the internal mechanisms that control the lever's motion.

Symptoms of a bad Ice Dispenser Door Lever include:

• Failure of the ice dispenser door to open when the lever is pressed
• The door opening erratically or becoming stuck
• Difficulty in dispensing ice due to the improper operation of the door

This OEM LG part is also compatible with some Kenmore models.

Replace a cracked or missing door bin with this door basket. It mounts to the refrigerator door to hold bottles and condiments, restoring safe, convenient storage and helping the door close properly.

• Attaches to the inner door to organize bottles and small items within easy reach
• Replaces a bin that is cracked, warped, or has broken locking tabs
• Symptoms include: bin falls off, won't stay seated, spills, or difficulty closing the door
• Restores designed door storage capacity and stability

• Unload the door and lift the old bin up and out of the mounting slots
• Align the new basket with the slots and press down until fully seated on both ends
• Do not force; confirm it's locked in before loading items
• Follow appliance safety guidelines; avoid overloading the bin after installation

The Spanner Wrench is an OEM replacement part for LG refrigerators. This tool allows you to adjust the door hinges to ensure the doors are level and aligned properly. A well-aligned door is crucial for maintaining the internal temperature and efficiency of the refrigerator, preventing energy loss and ensuring food is stored under optimal conditions.

Symptoms that you might need to adjust the door hinges and potentially need this wrench include:

• Doors not closing properly or sealing tightly
• Visible gaps between the door and the main body of the refrigerator
• The refrigerator tilting or not sitting level

This spanner wrench is also compatible with some Sears/Kenmore refrigerators. 

This turntable roller ring sits under the glass tray and allows it to rotate smoothly for even heating. Replace a worn, warped, or broken ring to restore stable rotation and consistent cooking performance.

• Supports the glass turntable and rides on built-in rollers for smooth, quiet movement
• Keeps the tray level and centered to promote even heating
• Common symptoms: tray not turning, uneven cooking, scraping/grinding noises, or a wobbly/slipping turntable
• Restores proper interaction between the turntable, drive coupling, and motor

• Unplug the microwave or switch off the breaker before servicing
• Remove the glass tray; lift out the old ring and clean the track
• Place the new ring with the rollers facing down on the track; reseat the tray on the center drive coupling
• Test rotation with a microwave-safe cup of water

This drawer tray assembly forms the shelf/base that supports a slide-out bin inside the refrigerator. Replace a cracked or warped tray to restore stable food storage and smooth drawer movement.

• Supports a slide-out drawer and food items in the fresh food or freezer section
• Helps drawers track correctly and sit level
• Damage can lead to binding drawers, tilting contents, or reduced storage
• Common signs: cracked plastic, sagging tray, drawer hard to open/close, visible wear

• Disconnect power and remove food from the affected area
• Slide out and remove the drawer(s) resting on the tray
• Lift out the damaged tray; transfer any reusable trim from the original if applicable
• Seat the new tray fully in the supports and reinstall the drawer(s)

This tray cover assembly replaces a damaged cover above a storage tray or drawer. It restores a flat, supportive surface and smooth operation, keeping the interior organized and preventing items from tipping or the drawer from binding.

• Forms the top cover/shelf over a tray or drawer and supports items stored above
• Helps align the tray/drawer so it opens and closes smoothly
• Replaces cracked, warped, or broken covers that cause sagging or jams
• Ideal when the existing cover is visibly damaged or unstable

• Disconnect power and remove contents from the area before servicing
• If present, lift out any removable glass insert before removing the frame
• Release tabs or screws, remove the old cover, and transfer any reusable components
• Seat the new assembly fully and reinstall any inserts and contents

This holder bracket replaces a damaged or missing mounting support. It secures an internal component so it stays aligned and stable, helping your appliance operate smoothly without looseness or rattling.

• Provides a rigid mounting point to hold a component or assembly in place
• Maintains alignment to reduce vibration, rubbing, and intermittent operation
• Restores support when the original bracket is cracked, warped, or missing
• Common symptoms include a loose/wobbly part, rattling noises, or visible broken tabs

• Disconnect power to the appliance before servicing
• Note the original bracket's orientation and transfer any clips or screws from the old part
• Use existing hardware and tighten fasteners evenly—do not overtighten
• Verify proper fit and alignment before restoring power

This dispenser lever holder is the mounting bracket behind the refrigerator's dispenser paddle. It supports and aligns the lever and switch so water or ice dispenses reliably when the paddle is pressed.

• Holds and guides the dispenser lever and actuator switch inside the dispenser housing
• Provides a secure pivot point for smooth paddle movement
• Helps ensure consistent activation of water and ice dispensing
• Damage can cause a loose or stuck paddle, intermittent dispensing, or no dispense

• Disconnect power and shut off the water supply before servicing
• Remove the dispenser panel/escutcheon to access the lever assembly; note part orientation
• Transfer the lever, switch, and return spring to the new holder and secure with the original fasteners
• Restore power/water and test dispensing before reinstalling trim

The PCB Assembly, Sub is an OEM part for LG refrigerators. It assists the main control board by regulating secondary refrigerator functions such as dispenser controls, ice makers, and temperature displays in specific refrigerator sections. Located inside exterior access panels, the sub board receives inputs and routes outputs behind refrigerator side panels and doors.

Causes of a bad sub board can include water damage to electronic components leading to shorts, as well as failure over many freeze-thaw cycles. 

Symptoms of a bad PCB Assembly, Sub include:

• Ice maker or water dispenser not operating 
• Incorrect temperature reading for sections  
• Error codes appearing on exterior display
• Buzzing or humming sounds from interior panels

This authentic LG replacement ensures all refrigerator features perform dependably. It is also suitable for Sears/Kenmore branded refrigerators containing LG mechanisms and controls. 

This is a replacement ice maker fill tube. This is a genuine OEM part made by LG and has been sourced directly from the manufacturer. This part is intended to replace broken or detached ice maker fill tubes in a variety of refrigerators. This piece of plastic tubing supplies the in-built refrigerator ice maker with water so it can make ice. If the ice maker is not working properly and is not making ice, there may be an issue with the tubing. Always make sure that the refrigerator is entirely disconnected from power and water before starting the any repair work. Please ensure that the appropriate safety precautions are followed when attempting to fix any appliances. For more accurate information on how and where to install this ice maker fill tube, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this ice maker fill tube is suitable for use on several different models of refrigerators manufactured by LG and Kenmore. This is a genuine part made of high-quality, durable plastic and is sold individually.

This adjustable leveling leg assembly supports and stabilizes your appliance by threading into the base frame. Replacing a worn or missing leg helps you level the unit for smoother, quieter operation on uneven floors.

• Provides height adjustment to level the appliance and distribute weight evenly
• Helps prevent rocking, wobbling, and excess vibration or rattling
• Can improve door alignment and smooth opening/closing when the cabinet is properly leveled
• Useful when a leg is missing, damaged, or threads are stripped

• Disconnect power; if applicable, shut off the water supply
• Use a helper to safely brace or tip the unit; protect flooring when accessing the leg
• Unthread the old leg and hand-thread the new one; tighten as needed
• Adjust front-to-back and side-to-side until stable; all legs bear weight evenly

This fan grille assembly covers and protects the refrigerator's fan while channeling airflow through the vents. Replacing a cracked or missing grille helps restore proper air circulation and can reduce noise and temperature fluctuations.

• Shields the fan blades and prevents items from contacting the intake
• Directs airflow to support even cooling throughout the compartment
• Typical symptoms: broken louvers or tabs, rattling/vibration noises, obstructed airflow, frost or warm spots near the fan area
• Restores the original airflow path and appearance after damage

• Disconnect power and clear shelves/drawers to access the panel
• Remove the screws/clips securing the old grille and retain any reusable hardware
• Position the new grille and fasten securely; ensure the fan spins freely and vents are unobstructed
• Restore power and allow temperatures to stabilize

The Filter Assembly, Head is an OEM replacement part for LG refrigerators. As an essential filtration component, the filter head houses the water filter and is responsible for dispensing clean, filtered water through the refrigerator's dispenser. It works to remove contaminants and improve taste.

Causes of a bad filter head can include normal wear and tear over time, mineral buildup within the head that impacts water flow, or damage to the head itself from accidental impact.  

Symptoms of a bad filter head include:

• Reduced or slow water flow from the dispenser 
• Noticeable declines in water filtration effectiveness
• Leaks or water damage around the filter head area

This OEM LG part is also compatible with select Sears/Kenmore brand models.

This fan grille assembly covers the internal fan and channels airflow through the air ducting, protecting the fan while helping your appliance circulate air efficiently for even, reliable temperatures and quieter operation. What it does:

• Shields the fan and directs airflow through the cabinet
• Helps maintain proper circulation for consistent cooling performance
• Replaces cracked, warped, or missing grille panels that disrupt airflow
• Common symptoms: rattling or scraping near the fan area, broken louvers, weak airflow, temperature fluctuations, or frost/ice buildup around the cover

• One fan grille assembly

• Disconnect power to the appliance before servicing
• Remove shelves/drawers or trim as needed to access the grille
• Remove mounting screws/clips and gently release plastic tabs; disconnect any attached wiring harnesses and note routing
• Transfer any reusable insulation or foam seals from the original part if present; ensure the fan spins freely before reassembly and restoring power