Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix a refrigerator not cooling properly with this compressor sealing pipe. Essential sealed system component for restoring proper refrigeration.
I changed the compressor, dryer and upgraded the software. Read more
This fan grille assembly covers and protects the refrigerator's fan while channeling airflow through the vents. Replacing a cracked or missing grille helps restore proper air circulation and can reduce noise and temperature fluctuations.
The part was easy to install in less than 30 minutes. The part came within two days and I watched the video twice. I followed the instruction step by step. Thanks. Read more
Mounts at the hinge to control door opening range and promote smooth closing. Replace if cracked, broken, or worn to restore proper door swing.
Replacing the door hinge and stopper assembly was very easy, once I figured out you had to disconnect the water supply on the back of the fridge before removing the door. Read more
Secures internal components in place to prevent rattling and misalignment. Replace if cracked, broken, or missing. Confirm fit with your model number.
Water pooling under your dispenser? This drip tray catches overflow and spills. Cracked or stained trays are easy to replace with basic tools.
Removed water dispenser housing using thin point kitchen knife insert knife at lower left side of housing twist knife and grab housing with finger nails carefully pulling as you move further along housing .the rest was pretty much easy, use small star screwdriver to remove micro switch.new switch is a little different.upon replacing housing start at the bottom up the sides to the top press firmly until you hear housing snap in tight Read more
Fix dispenser drips and spills with this refrigerator dispenser funnel. Guides water flow cleanly to prevent messes. Simple 5-minute installation.
This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.
Installed new screws. Read more
Supports and guides refrigerator drawers for smooth gliding. Replace when worn, broken, or causing binding. Confirm fit with your model number.
Replaced. Read more
Door hinge screws secure the refrigerator door hinges to the cabinet frame, allowing proper door operation and alignment. Replace when doors sag, don't close properly, or screws are loose, stripped, or missing causing door misalignment.
Vibration-isolating grommet that mounts between the compressor and chassis. Replace if cracked, worn, or missing to restore proper cushioning.
Ice maker grinding or not ejecting cubes? This gear drives the ejector blades to push ice from the tray into the bin. Restores harvest cycles quickly.
This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.
The old filter head was broken at the supply line side connector fell out. The clicking noise eventually caused the fridge to warm up and stop cooling. The clicking was the overload relay tripping. The Start solenoid on the compressor was an Embarco TSD part 513604044. APP does not have that part nor does any else found a similar one on ebay but I ordered the PTC assembly 6749C-0014E. I removed the overload relay and capacitor from the TSD used two pieces of wire and connectors to create the... Read more
Fix refrigerator not cooling or freezing issues with this evaporator assembly. Essential component for proper temperature control in bottom-mount models.
Rattling or loose parts in your refrigerator? This retaining pin secures moving components and keeps them aligned for smooth, quiet operation.
I removed the back cover and ground the old axel in had to remove it. I used two carpenter shims hammered under the frame to lift the refrigerator off the ground and put in the new wheel and axel. I used a concrete chisel and hammer to deform the axel end to lock it in place. Refrigerator is now rolling smoothly. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.