Lfx31945st Parts

This replacement gasket seals the Home Bar (door-in-door) access panel on your refrigerator. A fresh, flexible seal stops warm-air leaks that cause condensation, frost, and temperature fluctuations, helping the unit run efficiently and keep food cold.

• Forms an airtight seal around the Home Bar/door-in-door panel
• Helps maintain proper interior temperature and humidity
• Common symptoms: visible gaps, torn or warped gasket, condensation or frost near the panel, door not closing flush
• Restores reliable closing and reduces unwanted airflow

• Disconnect power before servicing
• Open the Home Bar panel, pull the old gasket from the channel, then align and press the new gasket fully into the groove—seat corners first
• Warm the gasket (hair dryer on low or soak in warm water) to relax folds; do not overheat
• Close and check for an even seal; adjust by massaging the gasket into place as needed

This center hinge assembly supports the refrigerator door at the mid-hinge position and allows smooth, reliable pivoting. Replacing a worn hinge restores proper alignment so the door closes and seals as designed.

• Provides the pivot point at the center hinge location
• Supports door weight to maintain alignment and clearance
• Helps ensure even gasket contact for an effective seal
• Common symptoms: door sagging or rubbing, squeaking at the hinge, difficulty closing, visible play or damage at the hinge pin

• Unplug the appliance and remove items from the door to reduce weight
• Support the door while removing the center hinge fasteners
• Note and transfer any spacers/washers in the same order and orientation
• After installation, align the door and verify the gasket seals evenly

Replacement door basket that restores convenient storage on the appliance door, keeping bottles and small items secure and accessible. Replaces damaged or missing door bins to help keep your appliance door organized and usable. What it does:

• Provides a secure shelf on the appliance door for bottles, condiments and small containers.
• Replaces cracked, chipped or broken door bins that no longer hold items safely.
• Restores lost or reduced door storage capacity for easier organization.
• Helps prevent items from falling out of the door during normal use.

• Disconnect power (unplug or switch off) and remove all items from the door before starting.
• Most installations are hand-operated: lift or tilt the old bin out of the door track, then seat the replacement into the same track—do not force.
• Inspect mounting clips or supports during replacement; damaged clips must be replaced separately.

This customized screw secures internal or external appliance components to restore proper fit and reduce movement. Use it to replace missing or damaged fasteners so panels and assemblies stay firmly attached during normal operation. What it does:

• Fastens panels, brackets, or small assemblies to maintain structural stability
• Prevents rattling, vibration noise, or loose trim caused by missing screws
• Restores correct alignment where a stripped or damaged screw allowed movement
• Works as a direct replacement for the matching screw specified for the repair

• One screw

• Disconnect power and water supply before starting any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but do not overtighten to prevent thread damage
• Keep small parts away from children and retain any removed hardware for reuse if needed

This damper controls airflow between compartments to help maintain proper temperatures and consistent cooling. It replaces a worn or broken damper to restore normal airflow and temperature balance inside the appliance. What it does:

• Regulates air flow between compartments so the refrigerator can maintain set temperatures
• Helps reduce uneven cooling and temperature swings caused by a stuck or broken damper
• Works as part of the appliance's air distribution system to route cooled air where needed
• Common symptom: compartment temperature too warm or inconsistent airflow noise from the damper area

• One damper assembly

• High-level replacement; access usually requires removing interior panels or duct covers
• Disconnect power before any repair to avoid shock or injury
• Handle with care to avoid bending or damaging mounting tabs and linkage

This cover assembly protects the machine components and helps keep internal machinery free of debris and accessible for repair. It provides a durable barrier that helps extend component life and maintains safe operation. What it does:

• Shields motors, belts and internal linkages from dust and lint that can cause wear
• Helps contain moving parts to reduce pinch or contact hazards during normal use
• Maintains proper component alignment by providing a stable mounting surface
• Commonly replaced when cracked, warped, missing fasteners, or damaged from impact

• One cover assembly as shown

• Disconnect power before attempting service
• Handle gently to avoid cracking plastic tabs; inspect mounting clips and screws for damage
• Reuse original fasteners only if undamaged; replace any stripped screws or broken clips

This drip tray catches and channels water runoff inside the appliance to help prevent pooling and minor leaks. It's a direct-fit replacement listed by the manufacturer and sold as the single tray used in the unit. What it does

• Collects condensate or defrost water and directs it to the drain area to prevent pooling.
• Helps stop water from dripping onto lower drawers, shelves or the floor.
• Commonly replaces a cracked, warped or missing tray that causes visible leaks or water buildup.
• Fits into the appliance's lower compartment where the original tray sat.

• Unplug the appliance or disconnect power before servicing.
• Remove any obstructing drawers or shelves to access the tray location; handle glass shelves carefully.
• Lift out the old tray and set the new tray into the same position; no special tools typically required.

This drain tray assembly collects and directs moisture and condensate to the drain system, helping prevent leaks and pooling under the appliance. Designed to fit the appliance's drain path and restore proper drainage. What it does:

• Captures condensate and channel water toward the drain to reduce standing moisture.
• Helps prevent water from pooling under components that could cause corrosion or odors.
• Restores proper drain routing after a damaged or cracked tray is removed.
• Works with existing hoses and clips to maintain normal drainage performance.

• Disconnect power and water before beginning repair.
• Remove access panels or components as needed to reach the drain tray; keep fasteners organized.
• Inspect surrounding seals, hoses, and clips and replace any worn parts to ensure a watertight fit.
• Reassemble panels and test the appliance for proper drainage and leaks before returning to service.

This holder assembly bracket secures and aligns a small appliance component so it stays in place during normal use, restoring reliable fit and reducing noise or movement caused by a loose part. What it does

• Provides a stable mounting point for the associated component to prevent shifting or detachment
• Restores correct alignment for doors, panels, or internal modules that rely on the bracket
• Helps stop rattling, vibration noise, or intermittent contact caused by a broken or bent bracket
• Supports safe operation by keeping parts properly positioned within the appliance

• Basic hand tools are usually all that's required; follow the appliance service manual for access steps
• Disconnect power (and water, if applicable) before starting any repairs to avoid shock or injury
• Inspect adjacent fasteners and mounting surfaces; replace any stripped screws or damaged clips for a secure fit

This door foam assembly replaces the inner insulating foam used inside a refrigerator/freezer door to restore thermal performance and reduce condensation. It helps maintain cold temperatures and improves energy efficiency when the original foam is damaged. What it does:

• Replaces worn, crushed, or missing door insulation to help maintain internal cabinet temperatures
• Reduces cold air loss and helps prevent moisture buildup and frost on the door interior
• Restores proper door fit and support when the original foam has deteriorated
• Can alleviate symptoms such as uneven cooling near the door edge, increased run time, or visible gaps/voids in the door

• One door foam assembly (inner door insulation), as shown

• Follow manufacturer service manual steps; handle foam carefully to avoid tears or compression
• Disconnect power if removal requires working near electrical components or lights
• Use appropriate adhesive/fasteners specified by the manufacturer when refitting the foam

This hinge cap covers and protects the door hinge, keeping the hinge assembly clean and improving the appliance's appearance. It replaces a cracked, missing, or worn hinge cover to help doors operate smoothly and look finished. What it does:

• Covers the door hinge to protect mating surfaces from dirt and damage
• Hides hinge hardware for a cleaner, finished look
• Helps prevent debris from interfering with hinge movement
• Can resolve cosmetic issues and reduce risk of snagging on exposed hinge parts

• One hinge cap

• Remove power and open the door to a safe, supported position before starting
• Typically snaps or screws onto the hinge—retain original fasteners unless replacement required
• Inspect hinge and fasteners while installing; replace any damaged hardware