Lfxc 24726S/02 Parts

This overload protector is a direct-replacement electrical safety device that helps protect the compressor motor from overheating and overcurrent. It trips the circuit when the compressor draws excessive current, helping prevent damage and allowing normal operation once cooled. What it does:

• Detects excessive current or high temperature at the compressor and interrupts power to prevent motor damage.
• Helps stop hard-starting or repeated short-run cycles caused by motor overload.
• Commonly linked to symptoms such as a refrigerator or freezer that hums or clicks, runs briefly then stops, or fails to maintain proper cooling.
• Works with the start components to ensure reliable compressor startup and protect against electrical stress.

• Always unplug the appliance or disconnect power at the breaker before servicing.
• Handle compressor terminals and wiring carefully; avoid bending or damaging terminal tabs.
• Replace with the identical part number or OEM-specified protector to ensure correct fit and electrical ratings.
• After installation, restore power and observe the appliance through one full start/stop cycle to confirm normal operation.

This LED assembly restores screen illumination by replacing a failed backlight strip. It helps return even, bright lighting to the LCD panel so pictures and menus are visible again without the dim or dark display caused by burned-out LEDs. What it does:

• Replaces the display backlight to restore screen brightness and uniform lighting
• Can resolve symptoms like dim display, dark bands, flickering backlight, or no visible picture with audio
• Works as the LED lighting component mounted behind the LCD panel to illuminate the image
• Designed to match the original LED layout and connector for a direct replacement

• One LED assembly (backlight strip) as shown

• Disconnect power and remove the display panel and bezel before replacing the assembly
• Handle the LCD and LEDs carefully to avoid damage; avoid touching LED surfaces and circuit traces
• Observe ESD precautions and use appropriate tools;

This main PCB power control board assembly manages the appliance's power distribution and control functions to restore normal operation when the original control board fails. It provides the electronic control backbone for cycle and power management. What it does:

• Regulates and distributes electrical power to the appliance's major systems.
• Interprets user inputs and controls cycle timing, sensors and outputs.
• Can cause the appliance to be unresponsive, fail to start, or exhibit random resets when faulty.
• May trigger error codes or abnormal operation tied to control or power faults.

• Disconnect power before attempting any diagnostics or replacement.
• Observe electrostatic discharge (ESD) precautions and handle the board by its edges.
• Verify the part number on the existing board matches this assembly before installation.

This door basket is a direct-fit replacement refrigerator door bin that restores door storage for bottles, jars and other items. It keeps door contents secure and organized so you can use the full door storage again. What it does:

• Replaces a cracked, broken or missing door bin that no longer holds items securely
• Provides stable storage for bottles, condiments and small containers on the refrigerator door
• Restores proper door seal clearance by returning the original bin height and fit
• Helps stop items from falling out when the door is opened or closed

• One refrigerator door basket/bin

• Remove all contents from the old door bin before starting
• Most installations snap into place: align mounting tabs with door slots and press until it clicks
• If screws or clips are present, retain original fasteners and reinstall as needed
• For safety, handle glass/jar contents carefully and avoid forcing parts; unplug the appliance if you will be working inside sealed compartments

This replacement home bar case is the molded compartment that fits into the refrigerator door to hold the home-bar area. It restores proper storage and support for bottles and accessories behind the home-bar door. What it does

• Serves as the molded housing/shelf for the refrigerator's home-bar compartment.
• Supports bottles and small items stored behind the home-bar door.
• Helps align and secure the home-bar door and internal components.
• Cracked or damaged cases can cause items to shift, rattle, or fall from the home-bar area.

• One home bar case

• Disconnect power to the appliance before beginning any repair.
• Remove the refrigerator door panel or inner liner as required to access the home-bar case; keep fasteners organized.
• Handle the plastic housing carefully to avoid further cracking; use correct OEM screws and clips for reassembly.
• Test the home-bar door operation and inspect for proper fit before returning the refrigerator to service.

This rail holder is a small mounting bracket that secures a sliding rail or guide to the appliance, restoring smooth movement and proper alignment. It's a direct-fit replacement designed to replace worn or broken rail supports. What it does:

• Secures and supports a sliding rail or guide so drawers/doors move smoothly
• Prevents rail movement that can cause rubbing, sticking, or uneven travel
• Restores proper alignment when a damaged holder causes noisy or wobbly operation
• Helps maintain safe rail attachment to the cabinet or frame

• Disconnect power (or unplug) and move the appliance to a safe, stable position before starting
• Basic hand tools are typically required; save mounting hardware unless replacement is specified
• If mounting screws or clips are damaged, replace them to ensure a secure fit

This customized screw secures internal or external appliance components to restore proper fit and reduce movement. Use it to replace missing or damaged fasteners so panels and assemblies stay firmly attached during normal operation. What it does:

• Fastens panels, brackets, or small assemblies to maintain structural stability
• Prevents rattling, vibration noise, or loose trim caused by missing screws
• Restores correct alignment where a stripped or damaged screw allowed movement
• Works as a direct replacement for the matching screw specified for the repair

• One screw

• Disconnect power and water supply before starting any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but do not overtighten to prevent thread damage
• Keep small parts away from children and retain any removed hardware for reuse if needed

This damper controls airflow between compartments to help maintain proper temperatures and consistent cooling. It replaces a worn or broken damper to restore normal airflow and temperature balance inside the appliance. What it does:

• Regulates air flow between compartments so the refrigerator can maintain set temperatures
• Helps reduce uneven cooling and temperature swings caused by a stuck or broken damper
• Works as part of the appliance's air distribution system to route cooled air where needed
• Common symptom: compartment temperature too warm or inconsistent airflow noise from the damper area

• One damper assembly

• High-level replacement; access usually requires removing interior panels or duct covers
• Disconnect power before any repair to avoid shock or injury
• Handle with care to avoid bending or damaging mounting tabs and linkage

This power control board manages and distributes electrical power to the appliance's major systems, restoring control functions when the original board fails. It's a direct-replacement control module used to regain normal operation. What it does:

• Regulates power and control signals for motors, valves, heaters, and user interface circuits
• Replaces a failed or damaged control board that can cause the appliance to not power on or to behave erratically
• Common symptom fixes: intermittent power, no response from controls, or control/display errors
• Works as the main electronic control hub that coordinates timed cycles and safety interlocks

• Disconnect power before starting any repair
• Use anti-static precautions and handle the PCB by its edges to avoid damage
• Verify connector orientations and secure all wiring before restoring power

This cover assembly protects the machine components and helps keep internal machinery free of debris and accessible for repair. It provides a durable barrier that helps extend component life and maintains safe operation. What it does:

• Shields motors, belts and internal linkages from dust and lint that can cause wear
• Helps contain moving parts to reduce pinch or contact hazards during normal use
• Maintains proper component alignment by providing a stable mounting surface
• Commonly replaced when cracked, warped, missing fasteners, or damaged from impact

• One cover assembly as shown

• Disconnect power before attempting service
• Handle gently to avoid cracking plastic tabs; inspect mounting clips and screws for damage
• Reuse original fasteners only if undamaged; replace any stripped screws or broken clips

This hinge cover assembly replaces a worn or damaged lid hinge cover to restore a smooth, finished look and protect the hinge area from debris and pinching. It helps keep the hinge area sealed and reduces snagging on the lid edge. What it does:

• Covers and protects the lid hinge and pivot area from dirt and moisture
• Restores a clean appearance where a cracked or missing hinge cover was visible
• Helps prevent clothing or hands from catching on the exposed hinge
• Can reduce rubbing noise caused by contact with a damaged cover

• Basic removal of the lid or access panel may be required; follow for proper disassembly
• Use appropriate hand tools and keep small fasteners secure during reassembly
• Disconnect power (and water for washers) before starting work to avoid injury

This filter assembly head secures and interfaces the refrigerator water filter cartridge, routing filtered water to the dispenser and icemaker. It restores a proper connection when the original head is cracked, leaking, or won't latch. What it does:

• Holds and seals the water filter cartridge in place for a secure connection
• Routes water from the supply line into the filter and onward to dispenser/icemaker
• Replaces a head that leaks, cracks, or fails to latch the filter properly
• Helps stop water leaks and restores normal water flow when the head is the faulty component

• One filter assembly head

• Turn off water supply and dispense any remaining water before beginning work
• Basic hand tools required; avoid over-tightening fittings to prevent cracks
• Inspect O-rings and tubing for damage and replace if needed

This Air Filter Assembly helps reduce odors and airborne particles inside the appliance for fresher-smelling air and improved interior environment. Designed as a direct-replacement filter assembly matching the OEM design. What it does:

• Captures odors and helps reduce airborne contaminants that cause unpleasant smells
• Restores the appliance's built-in air-cleaning function when the original filter is worn or missing
• Commonly replaced when you notice persistent odors or reduced air freshness inside the appliance
• Works as part of the appliance's ventilation/air circulation system to maintain interior air quality

• One complete air filter assembly (as shown)

• Refer to your appliance manual for the correct access panel and replacement procedure
• Replace with the appliance powered off and follow basic electrical safety if removal requires accessing wiring
• Verify correct orientation and secure mounting so the filter seals properly in the housing
• Dispose of the old filter per local regulations

This door gasket assembly replaces a worn or damaged refrigerator door seal to help restore an airtight seal and maintain proper cooling. A properly seated gasket reduces drafts, moisture intrusion, and energy loss. What it does:

• Seals the refrigerator door to keep cold air in and warm air out.
• Helps prevent frost buildup and moisture accumulation inside the compartment.
• Reduces compressor run time and energy usage caused by a leaking seal.
• Addresses symptoms such as warm spots, visible gaps around the door, or condensation on the door edges.

• Disconnect power to the appliance and remove food from the door area before starting.
• Inspect the door flange for damage and clean the mounting surface to ensure a proper seal.
• Seat the gasket fully into the channel; some models require loosening or removing trim screws to install.
• If the door does not close evenly after installation, check hinge alignment and adjust per the OEM instructions.

This guide assembly is a replacement plastic mounting guide that helps align and secure TV internal components and panels for stable operation and fit. Replacing a damaged guide restores proper panel alignment and reduces rattles. What it does

• Positions and supports TV panels or internal modules to maintain correct alignment
• Keeps components from shifting, which can cause rubbing, noise, or uneven gaps
• Helps ensure consistent fit of the bezel and display assembly after reassembly
• Restores secure mounting where original guide is cracked, broken, or missing

• One guide assembly

• Disconnect power and remove the TV from its stand or wall before starting
• Partial disassembly of bezel or rear cabinet is typically required; keep track of screws and clips
• Handle the panel and internal cables carefully to avoid damage; wear an anti-static wrist strap if available
• Test fit before final reassembly and power-up to proper alignment