Lfxs30766 Parts

This filter assembly head is the replacement water filter housing that secures the cartridge, routes incoming water, and seals the connection to the dispenser/ice system. It restores a proper filter mount and helps prevent leaks or loss of water flow. What it does:

• Holds and seals the water filter cartridge to the refrigerator's water line
• Routes filtered water to the dispenser and ice maker
• Commonly replaces a cracked, leaking, or damaged filter housing
• Can resolve reduced or no water flow when caused by a failed filter head
• Re-establishes a proper seal to prevent drips at the filter connection

• One filter assembly head

• Turn off the refrigerator and shut off the water supply before starting
• Depressurize the water line/dispenser per the refrigerator manufacturer's instructions
• Inspect O-rings/seals and replace if damaged; ensure proper seating when installing the filter
• After installation, turn on water, check for leaks, and run water/dispenser to clear air

This door stopper assembly mounts at the hinge to control how far the door opens and promote smooth, consistent closing. Replacing a worn or broken stopper restores proper door swing and helps protect the hinge from overextension.

• Limits the door's opening range to prevent overextension
• Guides and cushions door movement for a smoother close
• Helps maintain door alignment at the hinge area
• Common symptoms: door swings too far, doesn't stop at the usual angle, clicks/binds near the hinge, or visible cracks/wear on the stopper

• Disconnect power to the appliance before servicing
• Support the door and use a helper when loosening hinge hardware
• Note the original orientation and transfer any spacers/shims if present
• Tighten fasteners evenly and verify smooth door operation before finalizing reassembly

This holder is a small mounting bracket that secures a mating component in place inside the appliance. Replacing a cracked or missing holder restores a firm, rattle-free fit and proper alignment.

• Provides a stable mount for the designated part
• Prevents shifting and vibration that can cause noise or premature wear
• Common signs of failure: broken tabs, stress cracks, or the attached part sagging or falling out
• When damaged, the connected component may be loose, noisy, or misaligned

• Disconnect power; if working near water tubing, also shut off the water supply
• Note the original orientation and mounting points; take a photo before removal
• Reuse existing fasteners and avoid overtightening to prevent cracking the plastic
• Ensure the attached component is secure and clears any moving parts before restoring power

This cabinet roller supports the refrigerator and lets the unit roll in and out of place for cleaning or service. Replace a worn or broken roller to restore smooth movement and help keep the appliance properly positioned.

• Supports the base of the refrigerator and enables rolling movement
• Helps with safe positioning and service access without dragging
• Common failure signs: appliance is hard to move, scraping or rolling noises, a flat-spotted/cracked wheel, or a wheel that won't turn
• Replace when the roller is damaged, seized, or missing

• Disconnect power and shut off water supply; protect flooring before moving the appliance
• With help, pull the refrigerator forward and safely support it to access the roller
• Remove mounting fasteners, install the new roller, and reuse original hardware
• Confirm level and smooth movement before returning the unit to its location

This is the door handle mounting bracket assembly that secures the handle firmly to the door. It replaces a damaged or stripped bracket to restore a solid, wobble-free grip and reliable handle attachment.

• Mounts and secures the door handle to the door/frame
• Maintains alignment to prevent handle wobble or looseness
• Replaces cracked, broken, or stripped brackets to restore proper attachment
• Typical symptoms: loose or wobbly handle, handle pulls off, visible damage at the handle mount, rattling at the handle area

• Disconnect power before servicing and work carefully to avoid damaging the door surface
• Support the handle while loosening and tightening set screws or fasteners
• Retain and reuse original mounting hardware if it's in good condition
• Align the new bracket in the original location; do not overtighten fasteners

This is the appliance's primary electronic control board. It manages power distribution and system logic so cycles run correctly and key components receive the right power at the right time. What it does

• Distributes power to major loads (motors, fans, valves, heaters) per the appliance's design
• Interprets sensor inputs and coordinates timing for cycles and functions
• Addresses symptoms such as no power, won't start, intermittent or erratic operation, unresponsive controls, clicking from the control area, or recurring error codes
• Oversees safety and fault monitoring logic

• 1 main control board (PCB assembly)

• Disconnect power before servicing; allow capacitors on the old board to discharge
• Access the control compartment; photograph/label connectors to ensure correct reassembly
• Handle the board by the edges and use ESD protection; avoid flexing or touching components
• Inspect wiring and connected loads for shorts or damage before restoring power; follow the service manual

This replacement funnel channels flow cleanly through the dispenser/fill area, guiding it into the correct passage to help prevent spills, drips, and messes when the original piece is cracked, warped, or missing.

• Guides flow into the correct passage within the dispenser or fill area
• Helps reduce drips, leaks, and misdirected flow caused by damage or wear
• Restores clean, accurate dispensing and a tidy appearance
• Common symptoms include leaking/dripping at the dispenser, misdirected stream, visible cracks, or a loose/missing funnel

• Disconnect power; shut off water supply if applicable
• Remove surrounding trim or fasteners carefully and retain hardware for reuse
• Clean the mounting area before installing the new funnel
• Ensure tabs/locks fully seat; secure fit before restoring power and water

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

This replacement screw secures specified panels or components inside your appliance. Refreshing worn or missing hardware helps restore a tight fit, reduce rattling, and keep assemblies properly aligned for reliable performance.

• Provides secure fastening for brackets, panels, or internal assemblies
• Replaces stripped, rusted, or lost hardware
• Helps reduce vibration and rattling noises
• Symptoms include loose panels, shifting components, or a screw that won't tighten

• Disconnect power and allow any hot surfaces to cool before servicing
• Wear cut-resistant gloves and eye protection
• Match length and thread to the original; replace like-for-like
• Start threads by hand to avoid cross-threading; do not overtighten

This power cord assembly supplies AC power from the wall outlet to your appliance. Replacing a frayed, heat-damaged, or loose cord restores safe, reliable operation and can eliminate intermittent power loss.

• Carries line voltage and ground into the unit to power controls and components
• Routes electricity safely into the cabinet to protect internal wiring
• Replace at the first sign of damage to reduce shock or fire risk

• Disconnect power at the outlet/breaker before servicing
• Compare the new cord to the original; transfer any clips or grommets from the old cord if needed
• Route and secure the cord exactly as original; keep clear of sharp edges and moving parts
• Ensure all connections are fully seated and the ground is properly secured before restoring power

This gas valve assembly controls and shuts off the flow of gas to your appliance's burner system, enabling safe ignition and steady heat. Replacing a sticking or failing valve restores reliable heating performance and consistent flame control.

• Regulates gas flow to the burner(s) as commanded by the control/thermostat
• Works with the igniter to light the flame
• Helps maintain stable gas supply for consistent heating
• Failure symptoms include no ignition, igniter glowing with no flame, intermittent heat, or a weak/uneven flame

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool and work in a well-ventilated area
• Transfer any fittings or brackets from the original valve if required
• After installation, restore gas and check all connections for leaks with a soapy-water solution

This sub PCB assembly is an electronic control board that processes inputs and switches components, coordinating specific appliance functions. Replacing a failed board can restore normal operation and resolve dead controls, error codes, or intermittent, unpredictable behavior. What it does:

• Distributes and regulates control power and switches loads via onboard relays/triacs
• Interprets signals from sensors and the user interface to execute commands
• Coordinates timing and operation of related components per the appliance's program logic
• Failure may present as no power, won't start, unresponsive or flickering display, random beeps, or recurring error codes

• 1 sub PCB assembly

• Disconnect power to the appliance before servicing; verify no voltage is present
• Use ESD protection and handle the board by the edges
• Photograph wiring; transfer connectors one at a time and ensure they are fully seated
• Secure the board with existing fasteners/standoffs; perform any required reset or diagnostic per your model's service info

This hinge bolt secures the hinge to the appliance cabinet or door, keeping alignment true and motion smooth. Replacing a stripped, missing, or corroded bolt helps restore proper door operation and reliable closing.

• Fastens the hinge to support and stabilize the door
• Helps maintain alignment for smooth opening and closing
• Replaces damaged, stripped, or missing hardware

• Disconnect power to the appliance; shut off water supply if applicable
• Support the door to prevent strain on remaining hardware; enlist a second person if needed
• Note the order/orientation of any shims or washers and transfer them during reassembly
• Start threads by hand to avoid cross-threading; tighten securely without overtightening

The SWITCH, MAGNET is an OEM part for LG refrigerators. It is a switch designed to function in conjunction with the magnetic door seal, indicating to the refrigerator when the door is open or closed. This allows the refrigerator to regulate temperatures properly based on door positioning. 

Symptoms of a bad switch, magnet can include:

•  Temperature control issues, with the fridge struggling to maintain proper coolness levels
•  The fridge fails to switch to energy-saving modes when the door is closed 
•  Lights not turning on or off correctly when the door is opened or closed

Replace yours today with this genuine OEM LG part to ensure consistent and reliable temperature control. This OEM LG part is also compatible with Sears/Kenmore.