Lfxs32726s Parts

The Magnet Switch is an OEM part for LG refrigerators. It plays an important role in monitoring the position of the refrigerator door. 

The magnet switch works together with a magnet installed in the door gasket to detect when the door is opened or closed. It communicates this information to the control board which uses it to manage temperatures and fan speeds accordingly. 

Causes of a bad magnet switch can include wear and tear over time, physical damage, or failure of internal components. 

Symptoms of a bad magnet switch include:

• Improper cooling and freezing performances 
• Inability to detect when the door is opened
• Erratic temperature fluctuations
• Errors codes relating to door sensors

This genuine OEM LG magnet switch restores the door monitoring functions of your refrigerator. It is also compatible with Sears/Kenmore refrigerator models.

Fix water leaking inside your refrigerator with a new filter housing assembly. Secures the cartridge and seals connections. Moderately easy DIY repair.

Freezer not cooling or making noise? This evaporator fan motor circulates cold air throughout your refrigerator. DIY-friendly repair in about 10 minutes.

If your refrigerator display is dead, shows error codes, or behaves unpredictably, this sub PCB assembly processes inputs and controls specific functions.

Mounts at the hinge to control door opening range and promote smooth closing. Replace if cracked, broken, or worn to restore proper door swing.

Fix dispenser drips and spills with this refrigerator dispenser funnel. Guides water flow cleanly to prevent messes. Simple 5-minute installation.

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

Vibration-isolating grommet that mounts between the compressor and chassis. Replace if cracked, worn, or missing to restore proper cushioning.

Door hinge screws secure the refrigerator door hinges to the cabinet frame, allowing proper door operation and alignment. Replace when doors sag, don't close properly, or screws are loose, stripped, or missing causing door misalignment.

Covers and protects the door hinge area on your refrigerator. Replace if cracked, broken, or missing to restore a finished look and shield wiring.

This gas valve assembly controls and shuts off the flow of gas to your appliance's burner system, enabling safe ignition and steady heat. Replacing a sticking or failing valve restores reliable heating performance and consistent flame control.

• Regulates gas flow to the burner(s) as commanded by the control/thermostat
• Works with the igniter to light the flame
• Helps maintain stable gas supply for consistent heating
• Failure symptoms include no ignition, igniter glowing with no flame, intermittent heat, or a weak/uneven flame

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool and work in a well-ventilated area
• Transfer any fittings or brackets from the original valve if required
• After installation, restore gas and check all connections for leaks with a soapy-water solution

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

Ice maker grinding or not ejecting cubes? This gear drives the ejector blades to push ice from the tray into the bin. Restores harvest cycles quickly.

Refrigerator not cooling or running constantly? The compressor circulates refrigerant through the cooling system. Professional installation required.

Rattling or loose parts in your refrigerator? This retaining pin secures moving components and keeps them aligned for smooth, quiet operation.