Lgbd02432lw0a Parts

This is a replacement dishwasher rack assembly with factory-installed wheels. It restores smooth sliding and safe loading when the original rack is bent, rusted, or missing rollers—helping the rack glide properly and keep items positioned during the wash.

• Holds and organizes dishes, glasses, and cookware during cycles
• Integrated wheels ride on the tracks for easy loading and unloading
• Replace if tines are rusted/broken, wheels are cracked or missing, or the rack derails
• Helps prevent items from tipping and maintains consistent spray coverage

• Disconnect power to the dishwasher before servicing
• Open the door, extend the rack, release any rail end-stops, and remove the old rack
• Transfer any removable accessories from the old rack to the new one, if needed
• Slide the new rack onto the rails and reinstall end-stops; verify smooth operation

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

This Shield is a protective cover used in select appliances. It helps guard nearby components and guide airflow or heat as designed, restoring proper protection when the original shield is cracked, warped, damaged, or missing.

• Acts as a barrier/deflector to protect components from heat, moisture, grease, or debris as designed for your model
• Helps maintain intended airflow, heat path, or splash control inside the appliance
• Replace if the shield is cracked, warped, burned, broken, or missing
• Symptoms can include visible damage, scorched or discolored areas near the shield, rattling/vibration, or exposed areas that were previously covered

• Disconnect power before servicing; also shut off gas
• Wear gloves—edges can be sharp on metal shields
• Reuse original screws/clips unless your model provides replacements
• Seat the shield flat and do not overtighten fasteners

This kickplate (toe plate) replaces the lower front trim on compatible refrigerators to restore appearance and protect the cabinet base from scuffs and drafts. Durable sheet-metal construction keeps the front edge looking clean. What it does:

• Covers and protects the refrigerator's lower front area from kicks, scuffs and dirt.
• Restores a secure trim piece when the original is bent, dented or loose.
• Helps reduce visible gaps at the cabinet base for a neater fit.
• Improves appliance appearance after damage or during refurbishment.

• Disconnect power to the appliance or follow the manufacturer's safety guidance before beginning work.
• Remove the old kickplate by loosening the retaining screws or clips; lift out and set aside.
• Align the replacement plate, engage any clips or tabs, and reinstall screws; avoid overtightening.

A replacement bearing that supports the dryer drum and restores smoother, quieter rotation. Replaces a worn or damaged bearing to help reduce noise and prevent excess drum play. What it does

• Provides a low-friction mounting point for the drum shaft to rotate smoothly
• Keeps the drum aligned and reduces wobble during operation
• Helps prevent metal-on-metal contact that causes grinding or rumbling noises
• Can reduce strain on the motor and belt by restoring proper drum support

• Disconnect power before beginning any disassembly
• Replacement typically requires removing panels and the drum;
• Inspect surrounding seals, shafts, and mounting hardware and replace if worn

This genuine replacement screw secures appliance panels and components so assemblies stay tight and stable. It's a simple, direct fix when a missing or damaged screw causes loose trim, rattling, or misaligned parts. What it does:

• Fastens panels, brackets, and trim to restore proper alignment and stability
• Stops rattling or vibration caused by loose hardware
• Replaces stripped or corroded screws to ensure secure connections
• Works wherever the OEM screw is specified in the appliance

• Use the matching driver and proper torque to avoid stripping the head or threads
• Replace only with the exact OEM screw to maintain fit and function
• Disconnect power before accessing internal components; follow appliance safety instructions
• Replace all like-for-like for best results

Color: Stainless