Lghb2687pi7a Parts

This dispenser drip tray sits at the base of the refrigerator's ice/water dispenser. It catches small drips and splashes to help keep the dispenser recess and door front cleaner and drier. What it does:

• Collects minor drips and splashes from the ice and water dispenser
• Helps protect the door finish and surrounding area from moisture
• Replace if the tray is cracked, warped, stained, or missing
• Common signs include water pooling in the dispenser recess or a loose, ill-fitting tray

• 1 dispenser drip tray

• Pull the old tray straight out of the dispenser recess; no tools are typically required
• Clean any mineral deposits or debris in the recess before installing the new tray
• Align and seat the new tray flat and flush in the opening
• Disconnect power and shut off water

This thermistor is a temperature-sensing resistor that monitors internal temperature and reports it to the control. Replacing a faulty sensor restores accurate temperature feedback for proper operation and consistent, reliable cycle performance. What it does:

• Continuously measures temperature and changes resistance for the control to read
• Helps regulate heating/cooling and overall cycle timing
• Supports safety logic that prevents improper temperatures
• Failure may cause inaccurate temperatures, long/short cycles, or temperature-related error codes

• 1 thermistor

• Disconnect power before servicing; shut off water or gas if applicable
• Access the sensor, note wire routing/orientation, and transfer any existing clip or seal as needed
• Make secure electrical connections and route wires away from hot or moving parts
• Many appliances use multiple sensors—diagnose with an ohm/diagnostic test before replacement, then run a test cycle after install

This dispenser control board is the electronic module behind the refrigerator's ice/water dispenser panel. It reads button inputs and powers dispenser functions to help restore reliable dispensing and front-panel control when the original board fails. What it does

• Processes user selections for water, cubed/crushed ice, and dispenser light (model-dependent)
• Sends power to the water inlet valve and auger/dispenser motor as commanded
• Manages dispenser lock and status/display indicators (if equipped)
• Failure symptoms include unresponsive or intermittent controls, no water or ice dispensing, or an inoperative dispenser light

• Includes 1 dispenser control module (electronic board)

• Disconnect power before servicing; use ESD protection and handle the board by its edges
• Remove the dispenser escutcheon/cover to access the module; release locking tabs or screws as needed
• Transfer wire connectors one at a time to the new board, confirming orientation and full seating
• Reassemble, restore power, and test all dispenser functions

This door bin guard secures items on a refrigerator door shelf, preventing bottles and containers from sliding out. Replace it when cracked or missing to restore safe, usable door storage. What it does:

• Mounts to the front of a door bin to hold contents in place
• Replaces a broken, warped, or missing guard
• Helps resolve issues like items falling from the door shelf or a loose/broken bar
• Restores usable door storage space

• 1 door bin guard

• Unplug the appliance or disconnect power before servicing
• Empty the affected bin; release the old guard and align/snap the new guard into the slots
• Let cold plastic warm to room temperature before installation to reduce the risk of cracking
• The guard is fully seated before reloading items

This refrigerator water inlet tube routes water from the supply/valve into the appliance's water system. Replacing a cracked or kinked tube restores proper flow to the dispenser and ice maker while helping prevent leaks.

• Directs water from the inlet valve to internal components for dispensing and ice production
• Maintains a sealed, food-grade water path
• Replace if you notice leaks under/behind the unit, visible cracks/kinks, reduced or intermittent dispenser flow, or ice maker not filling
• Normal wear, brittleness, or damage during moves can lead to failures

• Disconnect power and shut off the water supply before servicing
• Place a towel or tray to catch residual water when disconnecting lines
• Note the original routing; release any retaining clips and disconnect the tube from fittings
• Route the new tube exactly like the original and fully seat tube ends in connectors; restore water and check for leaks

This replacement block is a small structural component used inside the refrigerator to locate, support, or align its mating parts. Replacing a worn or broken block restores proper fit and helps keep the affected assembly secure. What it does:

• Provides a stable mounting/locating point for the applicable assembly
• Helps maintain alignment and reduces wobble or looseness
• Common failure signs: cracks, missing piece, or stripped fastener hole
• Symptoms may include rattling, sagging, or parts that won't stay in place

• 1 block

• Unplug the refrigerator before servicing; wear cut-resistant gloves
• Remove items and any obstructing parts to access the block; note orientation for reassembly
• Transfer any reusable hardware from the old block and secure the new block without overtightening
• Restore power and verify proper fit and operation of the serviced area

This #10-32 x 3/4-inch machine screw secures appliance components such as panels, brackets, and handles. Using the correct length and thread helps restore a snug, rattle-free hold wherever this screw is specified by the manufacturer.

• Fastens components with a #10-32 machine thread and 3/4-inch length
• Helps keep panels, trim, brackets, or handles secured and aligned
• Replaces missing, stripped, or corroded hardware
• Common signs include loose or wobbly parts, rattling, missing screws, or damaged screw heads/threads

• Disconnect power before servicing; if working near a water connection, shut off the water supply
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping plastic or threads
• Reuse any model-specific washers or spacers if present

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

This thermistor is the refrigerator's temperature sensor. It monitors air temperature and reports to the control board so the compressor and fans run as needed for steady, accurate cooling.

• Monitors compartment temperature and sends a resistance signal to the control
• Helps regulate compressor and fan run time for consistent cooling
• Failure can cause temperatures that are too warm or too cold, food freezing in the fresh food section, or frequent cycling
• Some models display a sensor-related error code when the thermistor is out of range

• Disconnect power to the refrigerator before servicing
• Access the sensor, unplug the connector, and remove the old part
• Install the new sensor in the same location; transfer any mounting clip or insulation from the original part
• Route wiring as originally secured, fully seat the connector(s), and allow up to 24 hours after power-up for temperatures to stabilize

This control module manages key refrigerator functions to keep the appliance operating correctly. Replacing a failed module can restore normal cooling performance and dispenser/lighting responses, helping prevent temperature swings and inconsistent operation.

• Regulates electronic functions commanded by the refrigerator's controls
• May resolve symptoms like intermittent cooling, unresponsive dispenser or lights, or random beeping/errors
• Helps restore stable temperatures and normal control responsiveness
• Designed to fit specific Frigidaire/Electrolux-built refrigerators

• Unplug refrigerator before service; wear ESD protection when handling electronics
• Access location varies by model; take photos of wiring/connectors for reference
• Transfer any mounting hardware from the original part if reused
• After installation, restore power and allow 24 hours for temperatures to stabilize

This water connector links sections of the refrigerator's water supply tubing, maintaining a sealed path to the dispenser and ice maker. Replace a cracked or leaking connector to stop drips and restore reliable water flow and ice production.

• Connects sections of internal water tubing between components (inlet valve, filter, door, ice maker)
• Helps maintain a sealed route for proper dispenser and ice maker operation
• Common symptoms: water leaking behind/under the refrigerator, weak/no dispenser flow, ice maker not filling, visible damage at the fitting
• Direct-fit component built to OEM specifications for the intended application

• Unplug the refrigerator and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Cut tubing ends square and fully insert into the connector until seated; tug gently to confirm engagement
• Restore water, check carefully for leaks, and recheck after the first dispense cycle

Replacement push-button light switch that turns the interior light on and off when the refrigerator door opens. Replaces a failed or worn door-activated switch to restore interior illumination and make loading and unloading easier. What it does:

• Activates the interior light when the door opens and turns it off when the door closes.
• Restores visible interior lighting so food and shelves are easy to see.
• Stops lights from staying on or failing to come on if the original switch is worn or broken.
• Fits behind the fridge door trim where the original door switch mounts.

• Disconnect power to the appliance before servicing to avoid shock.
• Remove the door trim or liner cover to access the switch; keep track of screws and trim clips.
• Disconnect wiring harness or terminal connectors carefully; do not pull on wires.
• Reassemble panels and test the door action and light operation before returning to regular use.

The Mullion is an OEM part for Frigidaire refrigerators. It is situated between the freezer and refrigerator doors to separate the two compartments. The mullion provides structure, sealing the doors against air and temperature leakage.

Causes of a bad mullion can include wear and tear over time, damage from frequent door opening and closing, or impact damage.

Symptoms of a bad mullion include:

• Air and temperature leakage between compartments
• Difficulty closing one or both doors securely
• Gaps or cracks seen around the mullion frame
• Scratches, dents or other physical damage

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Crisper Pan is an essential OEM part for Frigidaire refrigerators. Located in the bottom of vegetable drawers, it collects moisture to hydrate and prolong the freshness of stored produce.

Symptoms of a faulty crisper pan include:

• Excessive leaks of water from the vegetable drawer  
• Produce items in contact with pan developing mold 
• Difficulty removing or replacing items smoothly

Causes may involve hairline cracks developing over time due to repeated vibration during door openings and closings. Mineral deposits can also reduce moisture collection effectiveness. 

This authentic OEM replacement is compatible for Frigidaire, Electrolux, and Kenmore models. 

Specs: Hex head ,1/4-20 x 5/8

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing