Lmv1650st Parts

This door interlock micro switch is part of the microwave's latch assembly. It detects when the door is fully closed so the oven only runs when latched, helping restore safe, consistent start/stop operation.

• Senses door-latch position within the interlock assembly
• Cuts power when the door opens; permits operation when fully closed
• Helps resolve "won't start" complaints or stopping when the door is jostled
• Often fixes the need to press or lift the door to keep the unit running

• Unplug the microwave before servicing; high-voltage components can retain a dangerous charge.
• Access the interlock/latch bracket behind the control panel; note switch orientation and terminal labels (COM, NO/NC).
• Transfer wires to the new switch, secure it in the bracket, and ensure the actuator aligns with the door latch.
• Reassemble and test with a cup of water to ensure proper start/stop operation.

This replacement door glass restores a clear viewing window and the protective barrier on your microwave door. Replace it when the original panel is cracked, shattered, or heavily scratched to keep the door secure and safe to use.

• Provides the see-through window and protective barrier within the microwave door
• Helps maintain proper door rigidity and alignment when intact
• Replace if the glass is cracked, chipped, shattered, loose, or badly scratched
• Reduced visibility, rattling, or visible damage are common symptoms of failure

• Unplug the microwave before servicing; microwaves can retain high voltage—use caution and do not open the cabinet
• Support the door; removal from the hinges may be required per your model's diagram
• Handle glass with cut-resistant gloves; edges can be sharp
• Transfer any reusable trim/clips as directed and verify the door latches and closes properly after installation

This truss head tapping screw secures panels, brackets, and covers in your appliance. Replacing a missing or damaged fastener restores a snug fit, reduces vibration, and helps keep components properly aligned for reliable performance.

• Provides low-profile holding power; wide truss head helps secure thin panels and trim
• Replaces lost, stripped, or corroded screws at the original mounting points
• Helps eliminate rattling, vibration, or loose handles/covers
• Addresses situations where a screw will not tighten or backs out during use

• Disconnect power; shut off water/gas if applicable before servicing
• Align parts and hand-start threads to avoid cross-threading
• Tighten until snug; do not overtighten to prevent stripping
• If the receiving hole is damaged, for repair before installing the new screw

The TEMPLATE is an OEM part for LG microwaves. It is the outer casing and control panel covering that defines the microwave's design and aesthetics.  

The causes of a bad template can include cracks, dents, or damage to the outer surface from impacts or normal wear over time. Heat and humidity fluctuations can also cause template materials to degrade.

Symptoms of a bad template include:

• Cracks or breaks in the template material
• Loose, misaligned, or damaged control panel or display  
• Yellowing, warping, or discoloration of plastics
• Openings or gaps that compromise the microwave structure

This genuine OEM LG replacement part restores the microwave's appearance and protects internal components. It is also compatible with some Kenmore and Sears microwaves
 

This thermostat controls oven/dryer temperature by opening or closing its contacts as the appliance reaches set temperatures, helping maintain safe and consistent operation. Replaces a worn or failed thermostat to restore proper temperature regulation. What it does:

• Senses temperature and interrupts heating when limits are reached to prevent overheating
• Re-establishes heating when temperature falls, maintaining normal cycle performance
• Commonly installed when an appliance won't heat, overheats, or cycles erratically
• Works as a direct replacement for the OEM thermostat designed for compatible LG units

• One thermostat

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Note wire locations or take a photo before removing wiring; reconnect wires to the same terminals
• Use a multimeter to verify thermostat continuity and correct operation before and after replacement

This factory fastener secures appliance panels and components. Use it to replace a missing, stripped, or corroded screw so brackets, covers, and assemblies stay tight and properly aligned, helping reduce vibration and rattling.

• Secures panels, brackets, and internal components in their proper positions
• Replaces missing, worn, or cross-threaded hardware
• Helps eliminate vibration and rattling from loose parts
• Supports proper alignment of covers and assemblies

• Disconnect power to the appliance before servicing; allow any moving parts to stop
• Match this screw to the location shown in your model's parts diagram
• Start threads by hand to avoid cross-threading, then tighten snugly with the correct driver
• Do not overtighten to prevent stripping threads or cracking plastic bosses

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

This truss head tapping screw secures interior panels and small components on compatible appliances, restoring proper fit and stopping rattles or loose trim. It's a direct hardware replacement for a single mounting point. What it does:

• Fastens panels, brackets, and trim where a low-profile truss head is required
• Replaces missing or stripped screws that cause rattling or loose parts
• Provides a secure hold by forming threads in sheet metal during installation
• Useful for repairing cosmetic or functional panel alignment issues

• Disconnect power before working on any appliance to avoid shock or injury
• Use the correct sized Phillips or Torx driver to prevent cam-out or screw damage
• Start straight and thread slowly; do not overtighten to avoid stripping sheet metal
• Replace only with the exact part number for best fit and performance

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

Inner plastic door film covers the holes in the inner door frame.

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

Size: 5 inches x 7 3/4 inches.