Lmx25988-St Parts

This sheathed defrost heater mounts at the evaporator and melts frost during the automatic defrost cycle to restore airflow and stable temperatures. Replacing a failed heater helps prevent ice-clogged coils, warm spots, and noisy fan interference.

• Melts frost from the evaporator coil during the defrost cycle to maintain proper airflow
• Symptoms of failure: persistent ice on the back panel, weak cooling, or the evaporator fan striking ice
• A failed heater can cause long run times and temperature swings
• Replace if the element tests open/short or shows visible damage

• Disconnect power before service; allow components to warm to reduce risk of cracking brittle plastics
• Remove shelves and the evaporator cover; carefully defrost ice—do not chip or pry against the fins
• Transfer original clips/insulators if present; route wires as original and make firm electrical connections
• After reassembly, ensure the drain area is clear and the fan spins freely

This sub PCB assembly is an electronic control board used in select LG appliances. It manages signals and low-voltage power for a specific feature or module, helping restore normal operation when the original board becomes unresponsive or fails.

• Provides low-voltage control for the designated function or user interface
• Communicates with the main control to execute settings and cycles
• Helps resolve symptoms such as unresponsive controls, blank/flickering display, intermittent operation, or related error codes
• Supports reliable operation of the affected subsystem after replacement

• Disconnect power at the breaker; shut off gas/water if applicable
• Use ESD protection and handle the board by the edges
• Photograph wire locations; transfer connectors one at a time to avoid miswiring
• Follow the service sheet for any required option-code entry, reset, or diagnostic check after installation

The Bracket Assembly is an OEM part for LG French door refrigerators housing circulation fan motors. This mounting bracket securely attaches the integral evaporator motor within the unit compartment. 

Causes of a bad bracket assembly can include loosened fasteners failing to firmly support vibrations over time, impact dents flexing the steel support reducing balance, or corrosion where steel meets refrigerant lines deteriorating contact points.

Symptoms of a bad bracket assembly include:

• Abnormal noises or grinding sounds from motor  
• Reduced airflow from the inlet to outlets inside the fridge
• Loose parts susceptible to movement damage 
• Misalignment reducing the lifespan of bearings

Replace yours today with this genuine OEM LG bracket to restore optimized cooling performance. Rigid clamping securely isolates motor oscillations. Compatible with Samsung, Kenmore, and GE French door models, this replacement sustains proper fit and function. 

This hinge cover fits over the door hinge to conceal and protect the mechanism. Replacing a cracked or missing cover restores a clean, finished look and helps keep hinge components shielded from dust, snags, and everyday wear.

• Conceals the door hinge for a finished, factory look
• Helps protect hinge hardware from dust and accidental contact
• Reduces snag points around the hinge area
• Typical failure signs: cracked plastic, broken tabs, missing cover, or a cover that won't stay attached

• Disconnect power before servicing; hinge areas can contain wiring
• Open the door and remove any retaining screw(s) or release the cover's tabs
• Lift off the old cover; align and snap or screw the new cover into place
• The door opens and closes freely with the cover installed

A replacement door gasket assembly that seals the refrigerator door to help maintain internal temperature and reduce energy loss. Restores a proper door seal to help keep food fresher and reduce cooling strain. What it does:

• Forms a tight seal around the refrigerator door to minimize cold-air loss and help maintain set temperatures.
• Helps prevent frost buildup and condensation inside the fresh-food compartment when the seal is compromised.
• Can reduce cycling frequency and excessive run time caused by a damaged or worn door seal.
• Common symptoms of a failing gasket: visible gaps, cold spots, frost or ice buildup, or condensation on the door edges.

• Disconnect power to the appliance before starting any repair.
• Remove food and door-mounted items as needed for safe access and handling.
• Align the gasket into the door channel, working it evenly around the perimeter so it seats fully; some distortion may correct after a short run time.

This basket assembly restores the washer drum that holds laundry and lets water flow for effective cleaning. It replaces damaged or worn baskets to reduce fabric snags and help restore smooth tumbling and even loads. What it does:

• Holds clothes during wash cycles while allowing water and detergent to circulate.
• Replaces baskets with dents, holes, corrosion or rough surfaces that can catch or damage fabric.
• Helps correct tumbling problems and reduce imbalance-related noise or vibration when the basket is damaged.
• Works with the washer's tub/bearing system to maintain proper rotation and drainage.

• Disconnect power and water before starting any repair.
• Replacing the basket typically requires disassembling the washer cabinet and removing the drive pulley, motor coupling or belt and possibly the tub/bearing—use appropriate tools.
• Inspect tub bearings, seals and suspension components while replacing the basket; replace any worn parts to prevent repeat failure.

This small retaining clip secures its mating component within the refrigerator assembly, keeping parts properly seated and reducing vibration. Replacing a damaged or missing clip helps restore a snug fit and reliable operation of the attached piece.

• Holds the designated part firmly in place within the assembly
• Maintains proper alignment to prevent movement or rattling
• Helps ensure panels, ducts, or lines stay secured during use
• Symptoms can include loose or sagging parts, vibration noises, or components that won't stay attached

• Disconnect power; if working near the water system, also shut off the water supply
• Note the original orientation and placement before removal
• Fully seat the mating component, then press the new clip into place without forcing
• Check operation before reassembly

This guide assembly is a chassis alignment and support piece that helps hold and position internal TV components for proper fit and operation. Replacing a damaged guide restores secure mounting and reduces panel or board movement. What it does:

• Secures and aligns internal TV modules or boards to the cabinet
• Prevents rubbing, vibration noise, and intermittent contact from loose parts
• Helps keep the display and internal assemblies correctly spaced for reliable operation
• Useful when cracked, warped, or broken guides cause misalignment or rattling

• One guide assembly as shown

• Unplug the TV and remove power/antenna cables before starting
• Ground yourself to protect against static-sensitive components
• Use original screws and fasteners; inspect adjacent tabs and mounts for damage during installation

This cover cap is a small plastic trim piece that protects exposed fasteners and improves the appliance's appearance. It snaps into place to hide mounting posts and help prevent snags or debris buildup. What it does:

• Covers and protects exposed screws, posts, or fasteners for a finished look
• Prevents lint, dust, and debris from collecting around the mounting point
• Reduces the chance of fabric snags or contact with sharp edges
• Restores worn or missing trim for improved cosmetics

• Disconnect power to the appliance before starting any service that exposes electrical components
• Usually installs by snapping over the post or press-fitting into the trim opening — no special tools required
• If needed, remove adjacent trim pieces to gain access, then reinstall trim in reverse order
• Inspect surrounding mounting hardware for damage and replace if necessary

This motor bracket assembly secures the appliance motor to the cabinet, keeping the motor properly positioned for reliable operation and reducing vibration or rubbing. Replaces a worn or damaged motor mounting bracket to restore stability. What it does:

• Holds the motor in place to maintain proper belt alignment and drivetrain geometry
• Prevents motor movement that can cause loud noise, grinding, or rubbing
• Reduces excessive vibration that can transfer to the cabinet or other components
• Helps maintain safe, consistent motor operation during spin or drive cycles

• Disconnect power (and gas if applicable) before starting any repair
• Support the motor before removing mounting hardware to avoid strain on wires or components
• Tighten all fasteners to OEM torque specs; replace any damaged brackets or fasteners
• Test operation after installation and re-check for proper alignment and noise