Lmxs307768/02 Parts

This electronic control board assembly replaces the PCB that directs your appliance's functions. Swapping a failed board can restore power, responsiveness, and proper overall operation.

• Regulates power distribution and timing to key components
• Interprets inputs from sensors and user controls to run programmed cycles
• Can resolve no power or dead display, won't start, unresponsive controls, intermittent operation, or error codes
• Often implicated after power surges or electrical damage

• Disconnect power before servicing; shut off gas/water if applicable
• Use ESD protection; handle the board by its edges and avoid touching components
• Photograph wiring and transfer connectors one at a time to the new board
• After installation, verify any required option settings or perform model-specific reset/diagnostics per the service information

This is the plastic front cover for the display/control area. It restores a clean, readable interface and protects the underlying control board and buttons from damage, wear, and moisture.

• Covers and protects the display and keypad area on the appliance
• Helps keep buttons aligned and accessible
• Replaces a cracked, discolored, or missing display cover
• Common symptoms: loose or broken trim around the display, buttons hard to access, cosmetic damage on the control panel

• Disconnect power before servicing
• Remove mounting screws/clips on the control panel, then lift off the old cover
• Transfer any reusable hardware or light pipes as needed
• Seat the new cover and secure fasteners without overtightening

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

This gas valve assembly controls and shuts off the flow of gas to your appliance's burner system, enabling safe ignition and steady heat. Replacing a sticking or failing valve restores reliable heating performance and consistent flame control.

• Regulates gas flow to the burner(s) as commanded by the control/thermostat
• Works with the igniter to light the flame
• Helps maintain stable gas supply for consistent heating
• Failure symptoms include no ignition, igniter glowing with no flame, intermittent heat, or a weak/uneven flame

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool and work in a well-ventilated area
• Transfer any fittings or brackets from the original valve if required
• After installation, restore gas and check all connections for leaks with a soapy-water solution

This sub PCB assembly is an electronic control board that processes inputs and switches components, coordinating specific appliance functions. Replacing a failed board can restore normal operation and resolve dead controls, error codes, or intermittent, unpredictable behavior. What it does:

• Distributes and regulates control power and switches loads via onboard relays/triacs
• Interprets signals from sensors and the user interface to execute commands
• Coordinates timing and operation of related components per the appliance's program logic
• Failure may present as no power, won't start, unresponsive or flickering display, random beeps, or recurring error codes

• 1 sub PCB assembly

• Disconnect power to the appliance before servicing; verify no voltage is present
• Use ESD protection and handle the board by the edges
• Photograph wiring; transfer connectors one at a time and ensure they are fully seated
• Secure the board with existing fasteners/standoffs; perform any required reset or diagnostic per your model's service info

This hinge bolt secures the hinge to the appliance cabinet or door, keeping alignment true and motion smooth. Replacing a stripped, missing, or corroded bolt helps restore proper door operation and reliable closing.

• Fastens the hinge to support and stabilize the door
• Helps maintain alignment for smooth opening and closing
• Replaces damaged, stripped, or missing hardware

• Disconnect power to the appliance; shut off water supply if applicable
• Support the door to prevent strain on remaining hardware; enlist a second person if needed
• Note the order/orientation of any shims or washers and transfer them during reassembly
• Start threads by hand to avoid cross-threading; tighten securely without overtightening

The SWITCH, MAGNET is an OEM part for LG refrigerators. It is a switch designed to function in conjunction with the magnetic door seal, indicating to the refrigerator when the door is open or closed. This allows the refrigerator to regulate temperatures properly based on door positioning. 

Symptoms of a bad switch, magnet can include:

•  Temperature control issues, with the fridge struggling to maintain proper coolness levels
•  The fridge fails to switch to energy-saving modes when the door is closed 
•  Lights not turning on or off correctly when the door is opened or closed

Replace yours today with this genuine OEM LG part to ensure consistent and reliable temperature control. This OEM LG part is also compatible with Sears/Kenmore.

The Thermistor Assembly, PTC is an OEM part for LG refrigerators. Located within refrigerator compartments, the thermistor monitors interior temperatures sending signals to the control board. It contains a temperature-sensitive resistor to provide precise feedback on cooling needs. This feedback allows the refrigeration system to maintain consistent temperatures across all food storage areas. 

The causes of thermistor issues arise from normal component degradation, impacts, water damage, and manufacturing defects affecting sensor accuracy.

Symptoms of a bad Thermistor Assembly include:

• Fluctuating or inaccurate temperature readings  
• Compartments failing to maintain proper cooling levels
• Frost or condensation builds up inside
• Repeated Auto Defrost error messages

This genuine LG replacement preserves dependable monitoring for balanced refrigeration control. Keeping food fresher longer and suitable for Sears/Kenmore refrigerators with LG components.

This compressor damper is a vibration-isolating mount that sits between the sealed-system compressor and the chassis. It cushions the compressor to reduce noise, limit vibration transfer, and help keep refrigerant lines from being stressed.

• Isolates the compressor from the frame to absorb start/stop shock and vibration
• Helps reduce humming, rattling, or buzzing from the back/bottom of the appliance
• Replaces a damper that's cracked, flattened, hardened, or missing
• Can help if the compressor rocks or the unit vibrates excessively

• Disconnect power and pull the unit forward for access; remove rear/service panel if present
• Support the compressor to relieve load on the mounts before removing fasteners
• Match orientation; transfer any sleeves/spacers from the old damper to the new one
• Ensure the compressor sits level and that tubing is not strained before restoring power

Replacement filter assembly head that holds and seals the refrigerator water filter cartridge and routes water to the dispenser and ice maker. Replaces damaged or worn filter heads to restore proper filter seating and help prevent leaks. What it does:

• Secures and aligns the water filter cartridge so the filter can seat and seal correctly.
• Channels water from the filter to the dispenser and ice maker.
• Stops leaks and drips caused by cracked, warped, or damaged filter head components.
• Restores proper water flow where a broken filter head was causing reduced or no water dispense.

• One filter assembly head.

• Turn off the refrigerator water supply and dispense water to relieve pressure before replacing.
• Remove the old filter and head per your owner's manual; install the new head and re-seat the filter until it locks.
• Check all connections for leaks after turning the water back on; hand-tighten only and avoid over-torquing.

This rail guide assembly restores smooth, stable sliding and alignment for a refrigerator drawer. It replaces worn or damaged drawer rails to help drawers open and close evenly and prevent sticking or dropping. What it does:

• Supports and guides the refrigerator drawer along its track for consistent movement
• Keeps the drawer aligned to prevent rubbing, sticking, or uneven closure
• Helps prevent the drawer from disengaging or falling out when pulled
• Reduces noise and binding caused by worn or damaged rails

• Disconnect power to the appliance or unplug before starting any repair
• Remove the drawer per your model's service instructions to access the rails
• Align the new rail assembly and secure with existing fasteners; do not force parts
• If you encounter damaged mounting points or broken fasteners, stop.

Replace a worn home bar door gasket to restore a tight seal and maintain proper cooling in the home bar compartment. This replacement gasket helps prevent cold air loss, reduce condensation, and improve temperature consistency. What it does:

• Creates an airtight seal around the home bar door to keep cold air in and warm air out.
• Helps reduce frost buildup, interior condensation, and uneven temperatures.
• Restores proper door contact to improve cooling performance and reduce strain on the compressor.
• Recommended when the gasket is cracked, torn, warped, or no longer seals evenly.

• Disconnect power to the appliance before beginning any service.
• Clean the door frame and mating surface before installing the new gasket for a proper seal.
• Remove the old gasket and press the new gasket into place evenly; check that the seal is continuous around the door.

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

Roller assembly that supports the dryer drum and helps it turn smoothly. Replacing a worn roller reduces squealing, prevents drum wobble, and helps extend belt life for quieter, more reliable drying. What it does:

• Supports the drum so it rotates evenly and maintains proper alignment
• Reduces noise like squealing, grinding, or thumping caused by worn rollers
• Prevents drum wobble and uneven wear that can stress the belt and seals
• Restores smoother drum rotation for more efficient drying performance

• Always disconnect power (and gas if applicable) before servicing the appliance
• Access the drum per the service manual—front or rear panel removal may be required
• Support the drum during removal/installation to avoid belt or seal damage
• Inspect associated parts (idler, belt, glides) and test the dryer after reassembly

This wiring harness assembly is the factory bundle of wires and connectors that links key components inside your appliance. Replacing a damaged harness restores reliable power/signal paths and brings affected features back to normal operation.

• Distributes power and control signals between control boards, sensors, motors, heaters, valves, and lights per the original design
• Helps address symptoms such as a component not operating, intermittent or dead functions, error codes, or visible burned/melted connectors
• Replaces broken, pinched, shorted, or corroded wiring that can interrupt circuits
• OEM-style connectors and lengths support proper plug-in fit and correct routing

• Disconnect power before servicing; do not rely on the appliance's power button
• Photograph/label each connection and note the original wire routing before removal
• Route the new harness exactly along the original path and secure in clips to prevent pinching, chafing, or heat contact
• Fully seat connectors; avoid pulling on wires when disconnecting or installing