Lre30453b Parts

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

This packing gasket seals the refrigerator door to help maintain proper temperature and energy efficiency by keeping cold air in and warm, moist air out. It replaces a worn, torn or misshapen door seal to restore a tight closure. What it does:

• Forms an airtight seal around the door edge to reduce cold air loss and prevent warm air intrusion
• Helps stop frost buildup and excess moisture inside the compartment
• Reduces compressor run time caused by air leaks
• Restores proper door alignment and improves cooling performance when old gasket is deformed

• One door packing gasket

• Unplug the appliance or shut off power before starting work
• Clean the door flange thoroughly and remove any old gasket adhesive or debris before installing
• Start at one end and press the gasket evenly into the channel; ensure full seating around the entire perimeter
• If needed, slightly warm the gasket with low heat (hair dryer) to make it more pliable—avoid overheating or stretching

A small structural support bracket that holds or stabilizes internal components. Replaces a worn or broken supporter to restore proper alignment and reduce movement that can cause noise or poor operation. What it does:

• Provides mounting support for internal panels or components to keep parts aligned
• Prevents sagging or shifting that can cause rubbing, vibration, or intermittent contact
• Restores proper component spacing after a cracked or missing bracket
• Commonly replaced when the original supporter is cracked, broken, or missing

• Disconnect power (and water supply, if applicable) before beginning any repair
• Basic hand tools may be needed; handle plastic brackets carefully to avoid breakage
• Inspect surrounding clips or fasteners and replace if damaged to ensure a secure fit

This supporter mounting bracket secures internal components or trim so they stay properly aligned and stable. It helps stop sagging, movement, and vibration that can affect operation or cause noise. What it does

• Holds and stabilizes a panel, shelf, or assembly to prevent shifting during use
• Reduces rattling, banging, or vibration caused by a loose component
• Keeps parts aligned for smooth opening and closing of drawers or doors
• Restores proper fit where a worn or broken support was causing misalignment

• Disconnect power (and water, if applicable) before servicing to avoid shock or flooding
• Inspect mounting points and screws; replace any damaged hardware for a secure fit
• Hand-start fasteners, then tighten snugly—do not overtighten plastic anchors

A circular lug designed to join a stripped wire to a threaded terminal for a secure electrical connection. Helps restore reliable contact at terminals and reduces the chance of intermittent power or arcing at connection points. What it does:

• Provides a strong mechanical and electrical connection between a wire and a screw or bolt terminal.
• Helps prevent loose connections that can cause intermittent operation, sparking, or overheating.
• Commonly used where a ring-style termination is required for safe, stable wiring.
• Works with properly sized wire and fasteners to maintain consistent conductivity.

• Always disconnect power to the appliance before inspecting or replacing electrical parts.
• Use the correct lug size and gauge for the wire and terminal; crimp or solder per manufacturer recommendations.
• Tighten terminal hardware to the appliance manufacturer's specified torque; avoid over-tightening which can damage the lug or terminal.
• If wiring insulation or the terminal is damaged or corroded, replace the affected components rather than reusing them.