Lre30757sb Parts

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

This packing gasket seals the refrigerator door to help maintain proper temperature and energy efficiency by keeping cold air in and warm, moist air out. It replaces a worn, torn or misshapen door seal to restore a tight closure. What it does:

• Forms an airtight seal around the door edge to reduce cold air loss and prevent warm air intrusion
• Helps stop frost buildup and excess moisture inside the compartment
• Reduces compressor run time caused by air leaks
• Restores proper door alignment and improves cooling performance when old gasket is deformed

• One door packing gasket

• Unplug the appliance or shut off power before starting work
• Clean the door flange thoroughly and remove any old gasket adhesive or debris before installing
• Start at one end and press the gasket evenly into the channel; ensure full seating around the entire perimeter
• If needed, slightly warm the gasket with low heat (hair dryer) to make it more pliable—avoid overheating or stretching

This supporter mounting bracket secures internal components or trim so they stay properly aligned and stable. It helps stop sagging, movement, and vibration that can affect operation or cause noise. What it does

• Holds and stabilizes a panel, shelf, or assembly to prevent shifting during use
• Reduces rattling, banging, or vibration caused by a loose component
• Keeps parts aligned for smooth opening and closing of drawers or doors
• Restores proper fit where a worn or broken support was causing misalignment

• Disconnect power (and water, if applicable) before servicing to avoid shock or flooding
• Inspect mounting points and screws; replace any damaged hardware for a secure fit
• Hand-start fasteners, then tighten snugly—do not overtighten plastic anchors

A circular lug designed to join a stripped wire to a threaded terminal for a secure electrical connection. Helps restore reliable contact at terminals and reduces the chance of intermittent power or arcing at connection points. What it does:

• Provides a strong mechanical and electrical connection between a wire and a screw or bolt terminal.
• Helps prevent loose connections that can cause intermittent operation, sparking, or overheating.
• Commonly used where a ring-style termination is required for safe, stable wiring.
• Works with properly sized wire and fasteners to maintain consistent conductivity.

• Always disconnect power to the appliance before inspecting or replacing electrical parts.
• Use the correct lug size and gauge for the wire and terminal; crimp or solder per manufacturer recommendations.
• Tighten terminal hardware to the appliance manufacturer's specified torque; avoid over-tightening which can damage the lug or terminal.
• If wiring insulation or the terminal is damaged or corroded, replace the affected components rather than reusing them.

This front plate is the outer trim panel that restores the appliance's appearance and protects internal components from debris and damage. It provides a clean, finished look and replaces scratched, dented, or missing front trim. What it does:

• Covers and protects the appliance front and control area from spills, dust, and impact
• Restores the exterior finish and alignment for a uniform appearance
• Helps keep internal components shielded from contaminants that can cause malfunctions
• Reduces gaps or misalignment that can interfere with door/hinge fit or seal

• One front plate

• Disconnect power (unplug or turn off breaker) before beginning any repair
• Removal typically requires taking off outer trim or door panels—use proper tools to avoid damaging adjacent parts
• Handle edges carefully; metal/plastic pieces may have sharp edges
• Follow the appliance's service manual or model-specific instructions for correct alignment and fastener torque

This replacement bar serves as the exterior door handle/trim that lets you open and close the appliance door smoothly while restoring the unit's original appearance. It's a direct-replacement style part designed to fit the factory mounting points. What it does:

• Provides a secure grip for opening and closing the appliance door
• Restores damaged, cracked, or cosmetically worn door trim/handle areas
• Helps maintain proper door alignment and fit when installed correctly
• Reduces draft and keeps the door sealing surface operating as intended

• One replacement bar

• Disconnect power (and for refrigerators, unplug the unit) before attempting removal/installation
• Remove any door shelves or trim blocking access; support the door during handle removal to avoid damage
• Reuse any required screws or brackets only if shown in OEM instructions; replace damaged fasteners