Lre30757sw Parts

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

This is a packing gasket that seals the oven door to the range cabinet, preventing heat from escaping during cooking. It is made of a flexible, heat-resistant material that lines the perimeter of the oven door. Replace this gasket if you notice excessive heat escaping from around the door, uneven cooking temperatures, or if the gasket is visibly worn, torn, or hardened.

This is a circular wire harness holder that secures and organizes internal wiring within the range. It clips onto the frame or mounting points to keep wires routed properly and away from heat sources. Replace this part if it is broken or missing, which can cause loose wiring or potential contact with hot surfaces.

The range packing seal creates an airtight barrier around oven doors or other range components to maintain proper cooking temperatures and prevent heat loss. Positioned around door edges or component joints, it needs replacement if heat escapes, cooking becomes uneven, or the seal appears cracked or compressed.

Replacement mounting screw for electric and gas ranges. Secures components and panels. Needed when original screw is stripped, missing, or damaged.

Structural support bracket that holds and stabilizes internal range components. Replace if cracked, broken, or missing to restore proper alignment.

Rubber bumper grommet for electric and gas ranges. Replaces cracked, worn, or missing grommets that cushion and support range components.

Replace a damaged or corroded range wiring harness that connects electrical components. Needed when the original harness is frayed, melted, or broken.

Replace your range's cracked or broken door handle. This handle attaches to the oven door front for opening and closing. Essential when original is damaged.

This front plate is the outer trim panel that restores the appliance's appearance and protects internal components from debris and damage. It provides a clean, finished look and replaces scratched, dented, or missing front trim. What it does:

• Covers and protects the appliance front and control area from spills, dust, and impact
• Restores the exterior finish and alignment for a uniform appearance
• Helps keep internal components shielded from contaminants that can cause malfunctions
• Reduces gaps or misalignment that can interfere with door/hinge fit or seal

• One front plate

• Disconnect power (unplug or turn off breaker) before beginning any repair
• Removal typically requires taking off outer trim or door panels—use proper tools to avoid damaging adjacent parts
• Handle edges carefully; metal/plastic pieces may have sharp edges
• Follow the appliance's service manual or model-specific instructions for correct alignment and fastener torque

This front control panel replaces the damaged or unresponsive user interface on your appliance, restoring button and display access for normal operation. It mounts on the appliance exterior and connects to the internal control assembly. What it does:

• Provides the primary button and display area used to start cycles and select settings
• Replaces cracked, scratched, or otherwise damaged front panel surfaces
• Restores response when physical buttons or touch areas are worn or nonfunctional
• Helps eliminate erratic or missing readouts when the panel housing is the source of the issue

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Handle the panel carefully to avoid glass or plastic damage and protect attached wiring
• Remove trim and mounting screws to access connectors; note connector positions before disconnecting
• Test the main control board and wiring harness for faults

This replacement bar serves as the exterior door handle/trim that lets you open and close the appliance door smoothly while restoring the unit's original appearance. It's a direct-replacement style part designed to fit the factory mounting points. What it does:

• Provides a secure grip for opening and closing the appliance door
• Restores damaged, cracked, or cosmetically worn door trim/handle areas
• Helps maintain proper door alignment and fit when installed correctly
• Reduces draft and keeps the door sealing surface operating as intended

• One replacement bar

• Disconnect power (and for refrigerators, unplug the unit) before attempting removal/installation
• Remove any door shelves or trim blocking access; support the door during handle removal to avoid damage
• Reuse any required screws or brackets only if shown in OEM instructions; replace damaged fasteners