Lsc23924st/02 Parts

Note: Evaporator with Defrost Heater

The water filter head holds the water filter and connects the water lines to the water filter. Approximate dimensions: 4.4" x 4.05" x 2.5"

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

This fan grill assembly covers and directs airflow for the evaporator fan, helping protect the fan and maintain proper circulation inside the compartment. It replaces a cracked, broken or missing grill to restore safe airflow and component protection. What it does:

• Protects the evaporator fan from debris and prevents contact with the spinning blades
• Directs airflow for consistent circulation across the evaporator coils
• Can reduce rattling or vibration caused by a damaged or loose grill
• Helps avoid airflow restriction that contribute to cooling issues

• Disconnect power to the appliance before any service to avoid shock or injury
• Typically installs behind an interior access panel; gentle trim removal may be required
• Inspect mounting tabs and clips; replace any damaged fasteners for secure fit
• Handle plastic parts carefully to avoid cracking; do not overtighten screws

This harness joint is a wiring connector that links two sections of an appliance wiring harness, restoring electrical continuity and reliable signal/power transfer. Use it to replace a damaged, loose, or corroded harness connection. What it does:

• Joins wiring harnesses so power and control signals pass between components
• Restores intermittent or lost electrical connections caused by broken or corroded terminals
• Helps eliminate symptoms like no power to a module, intermittent operation, or communication failures
• Maintains proper routing and strain relief where harness sections meet

• Disconnect power (unplug or shut off breaker) before inspecting or replacing wiring
• Match connector shape and terminal arrangement before installation; secure firmly until it clicks or seats
• Avoid forcing pins; inspect adjacent wires and insulation for damage and replace if needed

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

This pipe holder is a small plastic clip that secures tubing and small pipes inside the appliance, helping keep lines organized and preventing rubbing or disconnection. It restores proper routing and reduces vibration-related noises. What it does:

• Holds and secures water, drain, or refrigerant tubing to prevent sagging and chafing
• Keeps lines routed away from moving parts to reduce wear and noise
• Helps maintain proper tube alignment to avoid strain on fittings
• Commonly replaced when the original clip is cracked, broken, or missing

• Disconnect power and water before working on the appliance
• Inspect surrounding tubing and fittings for damage when replacing the clip
• Typically installs as a push-fit or snap-on clip; use gentle pressure and avoid forcing
• Replace broken or brittle clips to prevent tubing damage or leaks

This motor start/run capacitor helps the appliance motor or compressor start and run more reliably, restoring proper motor performance and reducing symptoms caused by a weak or failed capacitor. What it does:

• Provides the momentary electrical boost motors or compressors need to start
• Helps maintain stable motor operation during run cycles
• Resolves symptoms like motors that hum but won't start, intermittent starting issues, or cycling problems
• Replaces a worn or failed capacitor to restore consistent performance

• One replacement capacitor as shown

• Disconnect power before servicing and verify the appliance is de-energized
• Capacitors can hold charge — discharge safely before touching terminals
• Match terminal type and mounting location to the original part; do not force connections

This mechanical mounting band secures a bracket assembly inside the appliance to keep components aligned and reduce vibration. It restores proper bracket positioning so moving parts run quietly and reliably. What it does:

• Holds a bracket or component assembly in place to maintain proper alignment
• Dampens movement and reduces vibration-related noise or rattling
• Prevents excess wear by keeping parts from shifting during operation
• Helps maintain correct clearances to avoid interference or rubbing

• Disconnect power before inspecting or replacing internal parts
• Remove only the fasteners necessary to access the bracket; keep track of hardware
• Secure all fasteners to the manufacturer's torque or snug specification
• Replace the band if bent, cracked, or missing to restore proper fit and function

This door basket is a replacement refrigerator door bin that restores secure storage on the door shelves, helping keep bottles, condiments and small items organized and upright. What it does:

• Replaces a cracked, broken or missing door bin so items no longer fall out when opening the door
• Provides a molded shelf edge to keep bottles and containers upright
• Restores original storage capacity and organization to the refrigerator door
• Designed to snap into the door shelf mounting points for a stable fit

• One refrigerator door basket

• Remove all items from the door before replacing the bin
• Align the bin with the door shelf mounting slots and press until it snaps into place
• No special tools typically required; handle with care to avoid cracking plastic

This guide rail supports and stabilizes the dryer drum, helping it rotate smoothly and reducing wobble or noise. Replaces a worn or broken rail to restore quieter, more reliable drum movement and proper drum alignment. What it does:

• Provides a smooth, low-friction surface for the drum to ride on during operation
• Prevents drum wobble and rubbing that can cause noise, uneven wear, or belt strain
• Helps maintain proper drum alignment for effective tumbling and airflow
• Useful when the original rail is cracked, worn, or missing mounting surfaces

• One guide rail

• Turn power and gas off before beginning service; disconnect the appliance
• Basic disassembly of the dryer front or cabinet may be required; follow OEM instructions
• Inspect adjacent rollers, glides, and mounting brackets for wear and replace as needed
• Use proper tools and reference the dryer's service manual