Lsc27590sw Parts

A momentary push-button switch that restores reliable button control on the appliance console. Replaces a worn or non-responsive push switch so the control board receives a clear input when the button is pressed. What it does:

• Sends a momentary electrical signal to the control board when pressed
• Replaces broken, stuck, or intermittently working push buttons
• Helps resolve symptoms like no response from the console, intermittent button function, or a physically damaged button
• Functions as the user input for single-press commands

• One momentary push switch

• Disconnect power before servicing to avoid shock or injury
• Access usually requires removing the control panel or console; use appropriate screwdrivers
• Note connector orientation and gently unplug wire harness—do not pull on wires

This PTC cover protects the refrigerator's PTC/compressor start device from dirt, moisture and accidental contact, helping the start device operate reliably. It's a simple replacement that restores the protective enclosure for the start assembly. What it does:

• Shields the PTC/compressor start relay and wiring from debris and moisture that can cause malfunctions
• Helps prevent accidental shorting or contact with terminals during operation or service
• Can resolve symptoms where the start device is exposed or the compressor area shows visible wear or damage
• Maintains correct positioning and protection of the start components for consistent compressor starting

• One PTC cover (protective enclosure) as shown

• Disconnect power to the appliance before starting any repair
• Replace only when the start device or cover is exposed and you can access compressor/start assembly safely
• Avoid bending or stressing terminals and wiring when removing or installing the cover

This controller assembly is the main electronic control board that manages your appliance's cycles and user interface, restoring normal control when the original board fails. It replaces a faulty control module to help the unit operate reliably. What it does:

• Controls timing, cycles, and functions per user commands and sensor inputs
• Replaces malfunctioning or unresponsive control electronics that cause erratic operation
• Can resolve symptoms such as no power to controls, unresponsive buttons, or incorrect cycle behavior
• Works with existing wiring harnesses and display components when compatible

• Disconnect power before beginning work to prevent shock or damage
• Verify connector locations and orientation before removing the old board
• Handle the board by edges and avoid contact with circuitry to prevent static damage

This harness joint is a wiring connector that links two sections of an appliance wiring harness, restoring electrical continuity and reliable signal/power transfer. Use it to replace a damaged, loose, or corroded harness connection. What it does:

• Joins wiring harnesses so power and control signals pass between components
• Restores intermittent or lost electrical connections caused by broken or corroded terminals
• Helps eliminate symptoms like no power to a module, intermittent operation, or communication failures
• Maintains proper routing and strain relief where harness sections meet

• Disconnect power (unplug or shut off breaker) before inspecting or replacing wiring
• Match connector shape and terminal arrangement before installation; secure firmly until it clicks or seats
• Avoid forcing pins; inspect adjacent wires and insulation for damage and replace if needed

This handle assembly replaces a worn, broken, or missing refrigerator door handle to restore a secure grip and smooth opening. It mounts to the fridge door to return the appliance to normal use and appearance. What it does:

• Provides a finished, easy-to-grip handle for opening and closing the refrigerator door
• Replaces cracked, loose, or damaged handles that catch or wiggle when used
• Restores proper leverage for safe door operation and prevents further cabinet or trim damage
• Matches OEM fit and mounting points for straightforward replacement

• Disconnect power to the appliance or follow the manufacturer's safety guidance before starting work
• Remove food and any door-mounted items for easier access and to prevent spills
• Use the correct hand tools and avoid overtightening fasteners to prevent handle or door damage

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This snack tray assembly is the replacement interior sliding shelf that organizes small food items and keeps them accessible in the refrigerator. It restores a secure, easy-to-slide snack storage area to help reduce clutter. What it does:

• Provides a dedicated sliding shelf for storing snacks, condiments, or small containers
• Restores smooth sliding and proper alignment if the original tray is cracked, warped, or stuck
• Helps contain spills and keeps items organized on the refrigerator door or shelf area
• Replaces damaged or missing tray components that prevent normal use

• Unplug the appliance or shut off power before removing or installing interior parts to avoid electrical hazards
• Remove nearby items and shelves for easier access; handle the tray gently to avoid damage
• Align rails or guides and slide the tray into place until it clicks or seats fully

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

This main control board manages the appliance's power distribution and electronic controls so the unit runs its cycles and responds to user inputs. Replacing a failed board restores normal control and electrical operation. What it does

• Regulates power to motors, valves, sensors and user interface components.
• Processes user commands and cycle selection from the control panel.
• Communicates status and error signals to displays and other modules.
• Common symptoms of failure: no power or blank display, unresponsive controls, intermittent operation, or error codes related to control electronics.

• One main control board (power control board assembly) as shown.

• Disconnect all power before starting work to avoid shock or damage.
• Handle the board by the edges and avoid touching components; use ESD precautions if available.
• Verify the part number on the replacement board matches the original before installation.

This pipe holder is a small plastic clip that secures tubing and small pipes inside the appliance, helping keep lines organized and preventing rubbing or disconnection. It restores proper routing and reduces vibration-related noises. What it does:

• Holds and secures water, drain, or refrigerant tubing to prevent sagging and chafing
• Keeps lines routed away from moving parts to reduce wear and noise
• Helps maintain proper tube alignment to avoid strain on fittings
• Commonly replaced when the original clip is cracked, broken, or missing

• Disconnect power and water before working on the appliance
• Inspect surrounding tubing and fittings for damage when replacing the clip
• Typically installs as a push-fit or snap-on clip; use gentle pressure and avoid forcing
• Replace broken or brittle clips to prevent tubing damage or leaks

This motor start/run capacitor helps the appliance motor or compressor start and run more reliably, restoring proper motor performance and reducing symptoms caused by a weak or failed capacitor. What it does:

• Provides the momentary electrical boost motors or compressors need to start
• Helps maintain stable motor operation during run cycles
• Resolves symptoms like motors that hum but won't start, intermittent starting issues, or cycling problems
• Replaces a worn or failed capacitor to restore consistent performance

• One replacement capacitor as shown

• Disconnect power before servicing and verify the appliance is de-energized
• Capacitors can hold charge — discharge safely before touching terminals
• Match terminal type and mounting location to the original part; do not force connections

This mechanical mounting band secures a bracket assembly inside the appliance to keep components aligned and reduce vibration. It restores proper bracket positioning so moving parts run quietly and reliably. What it does:

• Holds a bracket or component assembly in place to maintain proper alignment
• Dampens movement and reduces vibration-related noise or rattling
• Prevents excess wear by keeping parts from shifting during operation
• Helps maintain correct clearances to avoid interference or rubbing

• Disconnect power before inspecting or replacing internal parts
• Remove only the fasteners necessary to access the bracket; keep track of hardware
• Secure all fasteners to the manufacturer's torque or snug specification
• Replace the band if bent, cracked, or missing to restore proper fit and function

This restrainer is a small retaining clip that helps secure moving or removable components in place, reducing rattles and keeping parts aligned for reliable operation. It's a simple replacement for worn or broken clips. What it does:

• Holds a cover, panel, or door-related component in proper position to prevent shifting
• Reduces noise caused by loose or vibrating parts
• Restores original fit where a broken or missing clip allows movement
• Simple mechanical function — no electrical connections or calibration

• One restrainer

• Disconnect power (and water if applicable) before beginning repairs
• Inspect surrounding mounting points for damage; replace any broken tabs or fasteners
• Typically installs with basic hand tools; align clip and press or snap into place until secure

The Ice Bucket Assembly is an OEM part for LG refrigerators. It is a component that stores ice from the icemaker in the freezer. The ice bucket assembly includes the bucket and the auger that dispenses the ice. 

Causes of a bad ice bucket assembly can include wear and tear over time, damage to the auger mechanism, or issues with the electronic components that control ice dispensing. 

Symptoms of a bad ice bucket assembly include:

• Ice cubes jamming or bunching up in the bucket
• Inability to dispense ice 
• Odd noises coming from the freezer area
• Ice falling out of alignment inside the bucket

This OEM LG part is also compatible with Sears/Kenmore. Replacing a faulty ice bucket assembly can help restore your refrigerator's icemaking and dispensing capabilities.