Lsdt9908ss Parts

Fix dishwasher not draining or OE error codes with a new check valve. Prevents backflow and keeps water moving properly. Easy 30-minute DIY repair.

This wire harness connects key internal components so power and signals are routed correctly. Replace a damaged harness to restore reliable operation when the original wiring is burned, brittle, cut, or causing intermittent electrical connection issues.

• Carries electrical power and control signals between designated components
• Restores dependable connections when wires or terminals are heat-damaged, broken, or corroded
• Helps address no-operation or intermittent operation of the affected component(s)
• Common clues include scorched insulation, loose/burned connectors, or visible wire damage

• Disconnect power before servicing; shut off gas/water if applicable
• Photograph/label connections and routing before removal
• Route and secure wiring exactly as original, away from sharp edges, hot surfaces, and moving parts; reuse existing clips/ties
• Seat connectors fully and avoid pulling on wires during removal/installation

Ice dispenser not working or ice won't dispense? This auger motor drives the ice dispenser mechanism. Most DIYers complete this repair in 15-20 minutes.

Connects internal water lines in your dishwasher. Replace if cracked, worn, or leaking to restore a secure seal and prevent water damage under the unit.

Closes off the bottom of the dishwasher cabinet to protect internal components. Replace if the panel is cracked, missing, or won't stay secured.

Replace cracked or worn dishwasher leveling legs. This foot assembly installs at the base corners to restore proper height adjustment and stability.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

Replaces a cracked, missing, or damaged control knob on your electric range. Restores secure temperature and cycle selection on the control panel.

Replaces the water supply tube that connects your household line to the ice maker and dispenser. Order when original tubing is cracked or leaking.

This seal strip replaces a worn or damaged door gasket edge to restore a proper seal and help the appliance maintain temperature and operate quietly. It's a direct-fit service part used where a continuous seal is required. What it does:

• Provides a flexible barrier along the door/frame to reduce air leaks and heat/cold loss
• Helps prevent moisture buildup and improves energy efficiency when sealing is restored
• Reduces rattling and vibration caused by a compressed or torn seal edge
• Commonly replaced when the strip is torn, missing, or no longer adheres properly

• One seal strip

• Disconnect power to the appliance before servicing to avoid electrical or burn hazards
• Clean and dry the mounting surface; remove old adhesive or residue for best adhesion
• Align the strip carefully and press firmly; allow any adhesive to cure per manufacturer instructions

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

Replaces a worn, cracked, or leaking hose connector in your dishwasher's water inlet assembly. Restores secure connection to prevent drips at joints.

Fixes unresponsive controls or features not working on your gas range. This cable assembly restores power and signal connections between components.

Secures the dishwasher door to the cabinet and provides a stable pivot point. Replace if your bracket is cracked, broken, or missing to restore alignment.

Black plastic corner cover replaces damaged or missing exterior trim on your refrigerator. Restores finished appearance and protects edges from wear.

This mounting clip secures the evaporator fan motor in place within your refrigerator's cooling system. It prevents motor vibration and ensures proper alignment for efficient air circulation. Replace when you hear rattling noises from the freezer section or notice reduced cooling performance.