Lsw01aw Parts

Fixes oven not heating, display issues, or erratic operation. This control board restores power distribution and core functions. Moderate DIY repair.

Harness retainer secures wiring harnesses inside your washer cabinet. Replace if cracked, broken, or missing to properly route and protect wires.

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

Fixes intermittent power or control issues caused by damaged wiring. This harness restores electrical connections between range components for reliable operation.

A balance weight that helps stabilize the washer tub during spin cycles to reduce vibration and prevent the appliance from rocking. Replaces a worn or broken cabinet weight to restore smoother, quieter operation. What it does:

• Adds mass to the washer cabinet to counteract tub imbalance during spins
• Reduces excessive vibration, shaking, and loud banging noises when spinning
• Helps prevent the washer from walking or shifting on the floor
• Works as the factory replacement for the original cabinet balance assembly

• Disconnect power and, if applicable, water supply before starting any repair
• Empty the drum and remove the required access panels per your model's service manual
• Securely fasten the weight using the original mounting hardware and torque per OEM guidance

A flat washer used with the appliance's fastening hardware to distribute load and reduce wear. Helps maintain secure connections and prevents damage to mating surfaces for reliable operation. What it does:

• Provides an even bearing surface for bolts or screws to prevent pull-through
• Reduces friction and wear between fasteners and housing parts
• Helps keep fasteners tight and resists loosening from vibration
• Commonly used where a smooth, protective spacer is needed

• Verify correct location and orientation before reassembly
• Use manufacturer-recommended fasteners and torque specifications
• Power off and unplug the appliance before accessing internal components

This is a circular wire harness holder that secures and organizes internal wiring within the range. It clips onto the frame or mounting points to keep wires routed properly and away from heat sources. Replace this part if it is broken or missing, which can cause loose wiring or potential contact with hot surfaces.

This high-voltage transformer supplies the high-voltage power needed by the microwave's magnetron so the oven can heat food. Replaces a failed transformer to restore proper microwave operation when the HV supply is the issue. What it does:

• Converts incoming mains voltage to the high voltage required by the magnetron
• Commonly fails when the oven produces little or no heat
• Can cause loud humming, burning smell, or visible arcing if damaged
• Failure may be accompanied by blown fuses or a tripped thermal cutoff

• Disconnect power and fully discharge the high-voltage capacitor before servicing
• Handle carefully; contains components that store dangerous voltage even when unplugged
• Follow OEM service manual wiring and mounting instructions; replace grounding and insulation parts as required

Range controls not responding or features intermittent? This wiring harness restores power and signal connections between components for reliable operation.

This is a VFD (vacuum fluorescent display) module that mounts behind the range's control panel and shows time, temperature, error codes, and cycle status. It communicates with the main electronic control board to relay information to the user. Replace this display board if the screen is blank, dim, flickering, showing incomplete characters, or displaying incorrect information even after a power reset.

Wall oven stopped moving or cycling intermittently? This AC synchronous motor assembly restores precise rotation and timing. Moderate DIY repair.

Fix a broken or unresponsive control dial on your wall oven with this circuit board assembly. Restores precise temperature control and oven functions.