Lsx26326s Parts

Small stopper that fits inside the handle assembly to limit travel and keep the handle properly seated. Replace if worn, missing, or broken to restore secure feel.

Upper hinge assembly for refrigerator doors. Mounts at the top to support and pivot the door. Replace if hinge is worn, cracked, or broken to restore alignment.

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

This controller assembly is the appliance's main electronic control that manages cycles and user inputs to restore proper control operation. Replace a failing controller assembly to address unresponsive controls, incorrect cycle behavior, or intermittent errors. What it does:

• Manages cycle selection, timing, and communication between sensors and motors to coordinate appliance operation.
• Interprets user inputs from the front panel and sends commands to other components.
• Failure may cause unresponsive buttons, unexpected error codes, stalled or incorrect cycles, or an appliance that won't start.
• Replacing the assembly often resolves control-board–related faults when diagnostics point to the main controller.

• Disconnect power (unplug or switch off breaker) before removing the old assembly to avoid shock or damage.
• Handle the board and connectors carefully; avoid static discharge and cradle the assembly by its edges.
• Match the replacement to the exact part number and transfer any brackets, grounding straps, or button housings as needed.

Fix no ice, slow water dispenser, or leaking water lines with this refrigerator water inlet valve. Controls water flow to ice maker and dispenser system.

Refrigerator not cooling consistently? Temperature sensor monitors compartment temps and signals the control board. Restores accurate readings.

This gas valve assembly controls and shuts off the flow of gas to your appliance's burner system, enabling safe ignition and steady heat. Replacing a sticking or failing valve restores reliable heating performance and consistent flame control.

• Regulates gas flow to the burner(s) as commanded by the control/thermostat
• Works with the igniter to light the flame
• Helps maintain stable gas supply for consistent heating
• Failure symptoms include no ignition, igniter glowing with no flame, intermittent heat, or a weak/uneven flame

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool and work in a well-ventilated area
• Transfer any fittings or brackets from the original valve if required
• After installation, restore gas and check all connections for leaks with a soapy-water solution

Refrigerator not cooling or making noise? This DC motor drives fans and mechanical components to restore proper airflow and temperature control.

Vibration-isolating grommet that mounts between the compressor and chassis. Replace if cracked, worn, or missing to restore proper cushioning.

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

Seals your refrigerator door to maintain stable temperatures and prevent frost buildup. Replace if torn, warped, or leaking. Confirm fit with your model.

Fixes warm or cool spots in your refrigerator. This fan guide assembly directs proper airflow in the compartment. Compatible with multiple models.

Replace a cracked, broken, or missing refrigerator shelf. Restores stable storage in the fresh-food compartment for organized food and container storage.

Fix noisy or seized fan issues with this refrigerator DC motor. Restores proper airflow and cooling performance when the original motor fails or weakens.

Refrigerator dispenser lever that controls ice and water dispensing through the door. Replace if cracked, broken, loose, or missing for proper function.

This is a clear plastic storage bin that mounts on the inside of the refrigerator door, commonly used for dairy items, condiments, or small containers. It snaps onto the door liner rails to hold items securely in place. Replace this bin if it is cracked, warped, or if the mounting clips are broken, causing it to fall off or not stay in position.