Ltcs24223w/06 Parts

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

This refrigerator guide aligns and supports a mating component so it travels smoothly and stays on track. Replacing a cracked or missing guide restores proper movement and helps prevent binding, jamming, or premature wear.

• Guides and stabilizes the movement of the associated part to ensure smooth travel
• Keeps components aligned to prevent rubbing, derailment, or gaps
• Common signs of failure: sticking or binding, wobbling/misalignment, or parts coming off track
• Visible damage such as cracks, broken tabs, or missing pieces on the guide

• Disconnect power; if working near a dispenser or water path, turn off the water supply
• Remove the access panel/bin as needed and retain any screws/clips
• Seat the new guide and reuse existing hardware; verify a secure fit
• Restore power and test the component's movement for smooth operation

This small control knob mounts on the shutter mechanism so you can open, close, or fine-tune the setting with a simple turn. Replace a cracked, loose, or missing knob to restore smooth adjustment and a clean, finished look.

• Attaches to the shutter/damper shaft to select positions
• Provides a secure grip for easy, precise adjustment
• Common failure signs: cracked or stripped hub, loose fit, missing knob
• May cause difficulty adjusting the shutter or settings to slip

• Disconnect power if removing any covers or panels near electrical components
• Pull the old knob straight off; rock gently if stuck to avoid damaging the shaft
• Align the keyed/D-flat opening with the shaft and press firmly until fully seated
• The shutter moves smoothly through its full range

The Door Basket is an OEM accessory specifically designed for LG refrigerator doors containing vegetable drawers. This hanging basket provides auxiliary storage directly above crisper bins.

Causes of a bad door basket can include wear and tear over time compromising the mesh material, or damage from overloading reducing structural integrity.  

Symptoms of a bad door basket include:

• Holes or tears reducing usable capacity   
• Detached fasteners slipping off mounting brackets
• Warped contours no longer remain properly installed
• Insecure attachment inhibiting safe door openings  

Replace yours today with this genuine OEM LG basket to maximize organizational convenience. Sturdy brackets produce a snug, stable fit. Compatible with Samsung, GE, and Frigidaire refrigerators featuring dual-drawer doors, this upgrade complements any modern kitchen setup. Reliable performance preserves aesthetic appeal.

The PCB Assembly, Display is an OEM part for LG refrigerators. It is responsible for controlling the refrigerator's display functions and interface. This board monitors temperature and cycle settings and regulates the input/output of operational data to the control panel. It assists users by displaying temperatures, selections, and error codes.

Causes of a bad display board can include liquid damage, thermal stresses from opening/closing doors over time, and short circuits due to manufacturing defects.

Symptoms of a bad PCB assembly include:

• Faulty or unreadable control panel display
• Buttons not responding properly  
• Random error codes appearing
• Glitches in temperature or function display

This genuine LG replacement ensures dependable control panel performance. It preserves your investment and restores full refrigerator operations. This part is also compatible with Sears/Kenmore models utilizing LG components and controls.

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

This main PCB power control board regulates power and controls key appliance functions so the unit can run its cycles and respond to user controls. Replaces a failed control module to restore normal operation and control. What it does:

• Provides the appliance's central control logic and power distribution to motors, valves, and user interface circuitry
• Processes user commands and cycle selections from the control panel
• Controls start/stop and timing functions; can cause failure to start or respond when faulty
• Can cause error codes, no power to components, or intermittent operation when damaged

• One main PCB power control board assembly

• Disconnect all power before starting work to avoid electrical shock
• Handle the board by the edges and avoid static discharge; use an anti-static wrist strap if available
• Reconnect all wiring harnesses securely and test the appliance through a full cycle after installation

A small retaining pin used to secure moving parts and keep components aligned for smooth operation. Replacing a worn or broken common pin can stop rattling and restore proper fit between linked parts. What it does:

• Holds or aligns two parts together so they move correctly and stay in position
• Helps prevent rattling, looseness, or parts slipping out of place
• Works as a simple mechanical fastener—no electronics involved

• One common pin

• Disconnect power to the appliance before beginning any service
• Keep track of small parts; lay out components in order to aid reassembly
• May require removal of trim or a hinge/retainer to access the pin—use basic hand tools
• If the pin is difficult to seat, do not force; inspect mating parts for damage

This customized screw secures specific appliance components to maintain proper fit and prevent parts from loosening during normal use. Use it when replacing a missing or damaged fastener to restore secure assembly and reduce vibration. What it does:

• Fastens panels, brackets, or components to the appliance frame
• Keeps parts aligned to prevent rattling or movement during operation
• Replaces stripped, missing, or damaged screws that cause loose assemblies
• Helps maintain electrical and mechanical connections by holding parts in place

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid overtightening which can strip threads or crack plastic
• Keep removed hardware organized for reassembly; replace any additional damaged fasteners

This customized screw is the manufacturer-specified fastener used to secure appliance components and panels at their mounting points. Replace a missing, stripped, or corroded original to restore a tight fit, proper alignment, and help eliminate vibration or rattling.

• Secures brackets, covers, and panels to the chassis at designated mounting points
• Maintains alignment and stability of the assembly during operation
• Helps address loose or rattling components caused by a missing or damaged fastener
• Direct replacement for the original fastener used in the specified location

• Disconnect power; shut off water before servicing
• Match head/length to the original; transfer any original clips or washers if used
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten until snug—do not overtighten into plastic or thin sheet metal

This supporter is a small mounting support used to secure and stabilize internal components, helping keep parts aligned and reducing vibration for quieter, more reliable operation. It restores proper fit where worn or damaged supports cause movement. What it does

• Holds and stabilizes a specific internal component or assembly to maintain proper alignment
• Reduces vibration and rattling caused by loose or broken supports
• Helps prevent wear from parts rubbing or shifting out of place
• Common symptoms it can address: unusual noise, wobble, or component misalignment

• One supporter mounting support

• Disconnect power to the appliance before beginning any work
• Access may require removing panels or assemblies—keep track of fasteners
• Inspect surrounding clips and fasteners and replace any that are damaged

This harness assembly routes power and signals between appliance components to restore electrical connections and normal operation. It replaces damaged or frayed wiring to stop intermittent power, control failures, or no-start conditions. What it does:

• Reconnects power and control circuits between major components
• Replaces damaged, burned, or frayed wires and connectors that cause intermittent or lost function
• Restores reliable signal paths to controls, sensors, and motors
• Helps resolve symptoms like sporadic operation, failure to start, or component non-response

• Disconnect power to the appliance before accessing electrical components.
• Match connectors and wire routing to the original harness during installation to avoid pin miswiring.
• Inspect connector pins and mating terminals for damage; replace the harness if pins are bent or corroded.

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This replacement mounting screw secures appliance panels and components to restore proper fit and reduce rattling or loose parts. Simple, direct replacement when a worn or missing screw causes loose panels or intermittent contact. What it does:

• Fastens panels, brackets, or small components to maintain proper alignment and reduce vibration
• Prevents loose trim, covers, or assemblies that can cause noise or improper sealing
• Replaces missing, stripped, or corroded screws that interfere with reliable operation
• Works wherever the OEM screw specification is required for secure mounting

• Use the matching screw hole and tighten until snug; avoid over-torquing to prevent stripping
• Disconnect power to the appliance if accessing electrical or moving parts near the work area
• If multiple screws are missing or panels are damaged, replace all fasteners for even support

The Power Cord Assembly is an OEM replacement part for LG refrigerators. It includes the electrical cord and strain relief that links the refrigerator to an external power source.  

This power cord assembly safely delivers electricity from the wall outlet to the internal compressor and fan modules. It facilitates proper cooling functions through this transmission of alternating current.

Symptoms of a bad power cord can include:

• Abnormal sounds such as humming or buzzing from within 
• Tripped circuit breakers interfering with operations
• Indicators of cord damage like frays or exposed wiring
• Inconsistencies in interior temperature maintenance

Causes may involve normal wear over extended use, physical stress, or accidental damage to the cord insulation.  

Replacing the power cord assembly with this genuine LG OEM part restores a reliable electrical pathway. It ensures a continued power supply to keep foods fresh and frozen.