Lte5243dqo Parts

This drum baffle restores the internal lift inside the dryer drum to help separate clothes and promote even tumbling. Replacing a cracked or missing baffle can reduce banging noises and help restore consistent drying performance. What it does:

• Lifts and moves clothes for more even tumbling and airflow inside the drum.
• Helps prevent garments from bunching or wrapping around the drum during a cycle.
• A damaged or missing baffle can cause loud thumping, scraping noises, or uneven drying; replacing it addresses these common symptoms.
• Designed to match the OEM drum mounting points for proper fit and function.

• Disconnect power (and gas, if applicable) before servicing the dryer.
• Access typically requires removing the dryer front or drum; keep track of fasteners and take photos for reassembly.
• Use basic hand tools and avoid forcing parts; inspect mounting hardware and drum condition while replacing the baffle.

This replacement buzzer assembly restores audible alerts and beeps for cycle status, touchpad feedback, and error notifications so you won't miss completed cycles or warning signals. It fits into the appliance's control area and connects to the existing wiring. What it does

• Produces audible beeps for cycle end, timer alerts, and control-pad feedback
• Signals fault codes and warnings so problems are noticeable
• Replaces a buzzer that is silent, weak, or intermittent
• Works with the existing control harness and mounting location

• One buzzer assembly

• Disconnect power to the appliance before servicing to avoid shock
• Handle control board and wiring gently; avoid bending pins or pulling on wires
• Test function before reassembling trim or panels

This lid assembly replaces a damaged or discolored top lid so your washer closes properly and looks like new. It restores the washer's top cover, improving cosmetic appearance and allowing the lid switch and hinge to function correctly. What it does:

• Replaces a cracked, warped or broken top lid that won't close or latch securely
• Restores the mounting surface for the lid switch and hinge so the washer can operate safely
• Improves the washer's appearance when the original lid is chipped, scratched, or yellowed
• Helps prevent dirt and debris from entering the tub area

• One lid assembly

• Disconnect power to the washer before starting any repair to avoid shock or injury
• Remove any screws or hinge pins securing the old lid; keep track of fasteners and springs
• Lift the old lid off the hinges and set the new lid into place, reinstalling hardware securely
• If the lid switch or hinge hardware is damaged, replace those parts separately.

This push-to-start replacement knob restores a worn, cracked, or missing control knob so you can easily engage your range/oven functions. Matches the original shape and feel for a secure, intuitive push action. What it does:

• Replaces a broken or loose push-to-start control knob so buttons and switches engage properly
• Provides a correct fit and turning/pushing feel to operate cooking controls
• Restores cosmetic appearance with the biscuit finish
• Helps prevent control slippage or uncomfortable operation caused by damaged knobs

• One push-to-start control knob (biscuit color)

• Always disconnect power to the appliance before attempting any replacement
• Pull the old knob straight off the control shaft and push the new knob on until fully seated
• If knob feels loose after installation, check the control shaft for damage—replace shaft or control if needed
• No special tools typically required;

This leveling link assembly connects and stabilizes the appliance's leveling system so the unit sits square and the door closes properly. It prevents uneven operation and helps stop rocking or tipping during use. What it does:

• Links the cabinet to the leveling leg so height adjustments transfer correctly
• Restores stable, even positioning to reduce rocking and misalignment
• Helps ensure the door seals and latches properly by keeping the appliance level
• Commonly replaced when links are broken, bent or separated from the leg/box

• One leveling link assembly

• Disconnect power to the appliance before servicing
• Support the appliance so it cannot tip when removing or installing the link
• Verify leveling leg height and alignment after installation; adjust legs as needed

This outer refrigerator door replaces a damaged or worn exterior door panel so your fridge seals and looks like new. It restores proper closure and helps maintain internal temperature control and appliance appearance. What it does:

• Replaces a damaged, dented or cracked outer refrigerator door panel
• Restores a straight, secure door edge for better sealing and operation
• Helps prevent cold air loss that can cause temperature fluctuations
• Improves appliance appearance by replacing scratched or faded exterior finish

• One outer refrigerator door panel

• Disconnect power and empty the door before starting; remove any screws or hinge covers securing the door
• Lift or support the door while removing hinge fasteners to avoid dropping or damaging the cabinet
• Align hinges and test door swing and seal before tightening all fasteners
• If inner components (bins, trim, gaskets) are attached, they should be properly reinstalled or transferred per manufacturer instructions.

Kit includes 2 sleeves.

This console clip secures the appliance control console or control panel to the cabinet, restoring a snug, stable fit and stopping rattles or loose movement. Durable plastic clip designed to replace a broken or worn fastener. What it does:

• Holds the control console in place to prevent sagging or separation from the cabinet
• Stops rattling or vibration noise caused by a loose console
• Restores proper alignment for buttons and switches on the control panel
• Replaces a cracked, worn, or missing mounting clip

• One console mounting clip (1 each)

• Disconnect power before attempting any service to avoid shock or injury
• Remove the console or access panel per your model's service instructions to reach the clip
• Pry out the damaged clip carefully and snap the new clip into the factory mounting boss until it seats
• Handle plastic parts gently to avoid cracking; before reassembling