Ltee5asp173tw01 Parts

Secures panels or brackets in your laundry center to prevent vibration noise. Replace missing, stripped, or worn screws to restore a tight fit.

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.

• Provides precise resistance to reduce voltage/current in the designated dryer circuit
• Supports proper operation of the timer, control board, or end-of-cycle signal (varies by model)
• Failure may present as a timer that won't advance, an inoperative signal/buzzer, or irregular cycle behavior
• Replace if visibly burned/damaged or if testing shows an open or shorted condition

• Disconnect power to the appliance before servicing
• Access the console/wiring harness and note original wire routing
• Make secure, insulated connections and route the resistor/leads exactly as original to avoid heat or chafing
• After installation, run a test cycle to ensure proper operation of the affected function

Fix a washer that won't advance to rinse cycle or stops mid-program. This timer controls wash, rinse, and spin sequences. DIY install in 5-10 minutes.

This Fan Blade is an OEM part for LG microwaves. It is a critical component designed to circulate air within the microwave, aiding in heat dissipation and ensuring even cooking. 

Fan blades in microwaves can suffer from wear, imbalance, or damage due to regular use or accumulation of debris. A malfunctioning fan blade can lead to inadequate ventilation, affecting the microwave's cooking efficiency and potentially causing overheating.

Symptoms of a bad fan blade include:

• Unusual noises during operation, such as rattling or buzzing, indicate a loose or damaged blade.
• The microwave overheating or shutting off prematurely.
• Inconsistent cooking or hot spots in food suggest poor air circulation.
• The fan not starting, or stopping unexpectedly during use.
• Visible signs of damage or wear on the blade.

This OEM LG part is also compatible with some Sears/Kenmore models.
 

The Washer Timer Dial is an OEM replacement part for Whirlpool washers. Positioned just behind the washer timer knob, the timer dial has a gray indicator that helps the user select the appropriate cycle. It interacts with the timer to ensure the washer operates in the correct mode and duration according to the chosen cycle.

Over time, the timer dial may degrade due to regular use, excessive force during cycle selection, or accidental impact. This can lead to inaccurate cycle selection, making it hard to use the washer efficiently.

Color: White

Symptoms of a faulty Washer Timer Dial include:

• Misalignment or sticking when choosing cycles
• Difficulty accurately selecting the desired cycle
• Cracked or broken indicator

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Agitator won't move or slips during wash? A worn drive shaft causes weak agitation. This shaft transfers motion from the gearcase to restore firm engagement.

This replacement drive motor powers your appliance's mechanical drive system. A worn or seized motor can cause humming, stalling, or a no-run condition. Installing a new motor restores reliable rotation and full cycle operation.

• Supplies rotational power to the unit's drive mechanism
• Can help fix: won't run/start, hums but won't turn, stalls or stops mid-cycle, trips breaker or overheats
• Helps reduce excessive buzzing or burnt-odor from a failing motor

• Disconnect power at the breaker before servicing; allow hot components to cool
• Access varies by model; photograph wiring and note routing before removal
• Transfer any brackets, pulleys/gears, or mounting hardware from the old motor if required
• After installation, verify the drive turns freely and no components are binding before restoring power

Replacement screw for securing panels, brackets, and internal components. Needed when original hardware is stripped, missing, or damaged during repairs.

This screw and washer is an OEM replacement part used for Whirlpool washers. It is used to secure the lid switch. Each screw is sold individually. The screw measures approximately 1 inch.

Leaking washer or water pooling near your laundry center? A cracked inlet hose is often the cause. This hose routes water from the valve to the drum.

Used for lid switch.

Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.

This is the inner glass panel that sits on the inside of the oven door, forming part of the insulated door assembly. It helps retain heat inside the oven cavity and protects the outer door glass from direct exposure to high temperatures. Replace this glass if it is cracked, shattered, or has visible damage that could compromise oven heat retention or safety.

This agitator mover is the upper auger section of a dual-action agitator. It ratchets in one direction to drive clothes downward for proper turnover, helping restore effective wash action when the original mover is worn or damaged. What it does:

• Creates the one-way, ratcheting motion of the agitator's upper section
• Helps circulate and roll laundry downward for thorough turnover
• Common symptoms of failure: weak agitation, top auger not advancing, clicking/slipping sounds, or visible cracks/stripped splines
• Needed after damage from overloading or long-term wear

• 1 agitator mover (upper auger)

• Disconnect power and turn off water before servicing
• Remove the fabric softener dispenser and agitator cap; take out the center retainer/bolt to access the mover
• Lift off the old mover and seat the new mover fully on the agitator
• Reinstall the retainer/bolt and cap; verify smooth ratcheting action before use

This is a fabric softener dispenser cup that sits inside the washer's agitator or dispenser housing and releases softener at the appropriate time during the rinse cycle. It is typically a small plastic cup or basket designed to hold liquid fabric softener. Replace it if fabric softener is not dispensing properly, the cup is cracked or warped, or you notice softener residue left on clothes.