Ltz1050 Parts

This small sealing washer fits the washer's water pressure assembly to help maintain a proper watertight seal at the pressure/valve connection. Replacing a worn washer reduces leaks and helps the fill/pressure system operate as intended. What it does

• Provides a watertight seal at the water pressure/valve connection to prevent leaks.
• Helps maintain correct pressure feedback to the washer's water control system.
• Wear or damage can allow leaking at the valve or inconsistent fill behavior.
• Simple, low-cost part commonly replaced when troubleshooting valve leaks.

• Turn off household water supply and unplug the washer before replacing.
• Remove the valve/pressure fitting carefully and replace the old washer with the new one, making sure it seats flat and undamaged.
• Inspect mating surfaces for debris or damage; clean before reassembly.
• If leaks or fill issues persist after replacement, inspect related seals, fittings, and the pressure switch/valve assembly.

This genuine OEM replacement part is a washer control board for commercial Speed Queen Washers. The control board is the main computer of a washer and controls the washing machine's essential functions. If the washer is no longer turning on, spinning, rinsing, or draining properly, it could mean that it needs to be replaced. Luckily replacing a control board is generally an easy repair.Start by unplugging the washer and pulling it out from the wall. Remove the upper back panel to gain access to the control board. Release the locking tabs that hold the control board in place and remove the wire harness along with any individual wires attached to the old board. Make sure to take note of the orientation of the wires by taking a picture with a phone camera. Reconnect the wire harness and individual wires into their correct terminals on the new board and snap it back in place. reinstall the upper back panel and put the washer back in place.This replacement part is sold individually and is compatible with Speed Queen Commercial washing machines.

This door liner seal provides a watertight barrier between the washer door and tub, helping prevent leaks and keeping laundry contained during cycles. Designed as a direct-replacement service part for compatible Speed Queen front-load washers. What it does:

• Seals the gap between the door and the tub to stop water from escaping during wash and rinse cycles
• Helps maintain proper drum containment and reduces water on the door opening
• Commonly replaced when you see visible wear, tearing, or persistent leaking from the door area
• Compatible with OEM door assembly designs that use a packaged liner seal

• Follow manufacturer instructions for proper seating and clamping
• Inspect surrounding door boot and latch for damage; replace if worn to ensure a proper seal
• Disconnect power and water supply before starting work to reduce risk of shock or flooding
• Test with a short cycle and check for leaks after installation

This replacement door boot is the flexible rubber seal that fits between the washer door and tub, keeping the wash chamber watertight and helping the door close snugly. Restores a proper seal and reduces leaks and odors. What it does

• Seals the door-to-tub gap to prevent water from escaping during wash cycles.
• Maintains a tight fit so the door closes evenly and the latch engages correctly.
• Helps reduce trapped moisture that can cause mildew, odors, or visible residue.
• Worn, torn, or distorted boots may cause visible leaks, puddling, or poor door closure.

• Disconnect power and water supply before starting any repair.
• Remove the outer door trim and/or retaining clamp carefully to avoid damaging the new boot.
• Inspect and clean the door frame and tub lip before installing the new boot to ensure a proper seal.
• After installation, run a short rinse cycle to check for leaks and correct seating.

This rear bulkhead assembly with seal replaces the washer's rear tub enclosure to restore a watertight connection and support the drum. It prevents leaks and helps maintain proper tub alignment for reliable operation. What it does:

• Seals the back of the washer tub to stop water from leaking at the rear
• Provides the mounting surface and alignment for the tub and rear components
• Helps prevent moisture damage to internal components and wiring
• Common symptom: water pooling or dripping from the rear of the machine

• One rear bulkhead assembly with seal

• Disconnect power and shut off water before beginning any repair
• Handle the seal carefully to avoid nicks; damaged seals can leak
• Basic hand tools required; verify fastener locations and torque per OEM guidance

This idler lever is the replacement lever that supports the washer's drive system, restoring proper belt tension and smooth drum rotation. Replacing a worn lever reduces slipping and helps the washer run quietly and reliably. What it does:

• Positions and tensions the drive belt or pulley to transfer motor power to the drum
• Restores proper belt alignment to prevent slipping or loss of drive
• Removes noise caused by a loose or damaged idler lever during spin or agitation
• Helps prevent uneven or intermittent drum movement linked to a failing lever

• One lever, idler

• Disconnect power before beginning any repair to avoid electric shock
• Inspect adjacent components (belt, pulleys, mounts) and replace if worn for best results
• Use basic hand tools; secure parts per the manufacturer's service instructions

A replacement self-tapping pan-head screw sized 10 x 5/8 in for securing appliance panels, trim and small assemblies. Restores proper fastening where original screws are missing, stripped or corroded. What it does

• Cuts its own mating thread in sheet metal or plastic for secure fastening
• Commonly used to attach control panels, trim pieces and small brackets
• Helps stop rattles, loose panels and misaligned trim when original fasteners fail
• Corrosion-resistant finish resists rust in typical laundry appliance environments

• Use the correctly sized screwdriver or driver bit to avoid stripping the head
• Start in a pilot hole if material is brittle or if reinstalling into worn threads
• Do not over-torque; stop when the head seats flush to avoid cracking or stripping
• Disconnect power and follow appliance-specific safety procedures before working

This shock absorber kit replaces worn suspension dampers to reduce tub movement and vibration for a quieter, more stable wash cycle. Designed to restore proper suspension response and help prevent excessive tub bounce or banging. What it does

• Dampens tub motion during agitation and spin to reduce vibration and noise
• Helps keep the wash basket centered to prevent excessive wear on other suspension parts
• Commonly used when the washer rocks, bangs, or feels unstable during cycles
• Restores smoother, safer operation for machines with weakened or leaking shocks

• High-level swap: remove access panels, support the tub, unbolt the old shock(s), and install the replacement(s)
• Disconnect power and water supply before starting any repair
• Use proper support/straps for the tub to avoid injury; shocks are under load
• If multiple shocks are worn, replace all affected shocks for balanced suspension

This hex washer-head screw secures panels and components in commercial washers and dryers, providing a low-profile, vibration-resistant fastener that helps keep assemblies tight and aligned during operation. What it does:

• Fastens sheet metal and plastic parts where a wide bearing surface is needed
• Hex washer head spreads load to reduce pull-through on soft materials
• Self-tapping thread cuts into mating material for a secure fit without a nut
• Commonly used where vibration and repeated motion can loosen standard screws

• Use the correct size driver or socket to avoid stripping the head
• Start the screw straight and apply steady pressure while driving to ensure proper thread engagement
• Tighten until snug — avoid over-torquing which can strip threads or crack panels
• Disconnect power and follow all safety precautions before servicing appliance

This hex head machine screw fastens appliance panels and components, restoring secure assembly and stopping movement or vibration. It's a simple replacement when original screws are lost or worn. What it does:

• Secures panels, brackets, and internal components to prevent rattling or misalignment
• Replaces missing or damaged screw heads that keep parts firmly attached
• Restores proper fit where stripped or corroded fasteners allow play
• Helps maintain safe operation by keeping covers and guards in place

• Disconnect power and water before working on the appliance
• Use the matching hex driver or socket to avoid rounding the head
• Replace like-for-like; tighten until snug but avoid over-torquing
• If threads are damaged, inspect mating part and replace as needed