Maytag Mvwc360aw0 Parts

This wire shield is a molded protective cover that helps keep wiring routed and protected from heat, abrasion and moving parts. It prevents chafing and reduces the risk of shorts for a safer appliance operation. What it does:

• Covers and routes wiring to protect insulation from heat and friction
• Prevents wires from contacting sharp edges or moving components
• Helps stop intermittent shorts, arcing, or wiring damage that can cause odor or failures
• Maintains proper wire position to support consistent electrical connections

• One wire shield

• Disconnect power to the appliance before beginning any work
• Secure with existing clips or fasteners; do not force or modify the part
• If wiring insulation is melted or damaged, replace wiring/harness before reassembly

This main wire harness routes power and signals between the appliance control and internal components to restore proper electrical connections and operation. It's a direct-fit replacement when the original harness is damaged. What it does:

• Connects control board, motors, switches and sensors so circuits receive power and communicate correctly
• Replaces frayed, broken, or corroded wiring that can cause intermittent operation or component failure
• Helps stop issues like no power to controls, intermittent runs, or unexpected shutdowns when caused by damaged wiring
• Maintains factory routing and connector types for reliable electrical connections

• One main wire harness

• Disconnect power (unplug or shut off breaker) before inspecting or replacing the harness
• Compare harness and connectors to the original and route wires following factory paths to prevent chafing
• Secure connectors fully until they click; avoid stretching wires when reinstalling

This left-hand end cap assembly restores a secure, finished mounting point on the appliance cabinet and helps keep internal components aligned and protected from friction or debris. Ideal when the original end cap is cracked, warped, or missing. What it does:

• Replaces a damaged or worn left-hand end cap to maintain proper alignment of adjacent components
• Provides a protective cover to prevent contact, rubbing, or debris entry at the cabinet edge
• Helps reduce vibration-related noise caused by loose or misaligned parts
• Fits into the original mounting location and matches OEM fit where specified

• Disconnect power to the appliance before starting any repair
• Verify left/right orientation by comparing to the removed part prior to installation
• Typical install requires removal of the adjacent trim or panel; handle parts gently to avoid damaging clips
• If mounting hardware is missing or damaged, replace with OEM-specified fasteners

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

This clamp secures a washer or dryer hose to its connection to prevent leaks and keep the hose firmly in place during operation. It replaces worn or loose clamps that allow water to escape or hoses to detach. What it does:

• Holds a washer/dryer hose to a nipple, collar or fitting to maintain a sealed connection
• Prevents water leaks caused by loose or corroded clamps
• Stops hoses from slipping off during drain or fill cycles
• Restores proper hose retention and reduces risk of water damage

• Disconnect power and turn off the water supply before starting any repair
• Inspect hose and fitting for damage; replace hose if cracked or frayed
• Use appropriate pliers or a screwdriver for the clamp style; avoid overtightening to prevent hose damage
• Verify a leak-free connection after restoring power and water

Note: Bearings are only available with the gearcase assembly.

This is a Whirlpool washing machine basket. The washing machine basket holds laundry during a wash cycle. The basket may become damaged over time due to normal wear and tear, which can be exacerbated by overloading laundry or using the wrong amount of detergent. When the basket starts to become damaged or malfunction, noticeable noise increases may take place during use. Eventually, the damage will lead to the basket failing to spin. The old basket can be removed by first removing the top portion by pushing the fastening clips that hold it in place. After removing the top, reach down to remove the softener cup. Using a socket, unfasten the agitator at the bottom of the basket. After removing the agitator, the basket should easily lift out of the machine.This part is a genuine OEM product and is sourced directly from the manufacturer. It is intended for use in Whirlpool, Maytag, Kenmore, and Crosley appliances.

Color: White. Size: 1 qt. can. Acrylic appliance paint.

Size: 10 - 24 x 3/8

This is a replacement top lid for compatible Whirlpool top-load washers, restoring the washer's top cover and helping keep clothes secure during operation. It replaces a cracked, dented, or missing lid to return the washer's appearance and function. What it does:

• Covers the washer tub to prevent objects from falling in and keeps laundry contained during cycles
• Restores the washer's finished appearance when the original lid is damaged or warped
• Helps maintain proper lid alignment for correct lid-close behavior and lid-lock engagement
• Reduces risk of items entering the wash area and limits moisture/soil exposure to internal components

• One replacement lid

• Disconnect power to the washer before starting any repairs to avoid electrical or mechanical hazards
• Remove the old lid by supporting it and detaching hinge fasteners; some models use spring clips or screws
• Handle the lid carefully to avoid chipping painted surfaces; use two people if the lid is large or awkward
• Test lid alignment and secure all fasteners before returning the washer to service