Maytag Pdb4600awe Parts

Specs: No.8X1/2 HEX WASHER HEAD

Screw: 8-16 x 3/8 inch.

Replacement screw secures appliance panels, brackets, and internal components. Needed when original screws are stripped, missing, or damaged during repair.

The Tub Wheel supports and guides the washer's tub assembly on its base during wash and spin cycles. Replacing a worn wheel restores smoother, quieter operation and helps reduce vibration and rubbing as the machine operates.

• Provides rolling support so the tub can move and self-balance during cycles
• Reduces friction between the tub and the base/frame
• Helps keep the tub centered to minimize noise and vibration
• Failure symptoms include squeaking or grinding, scraping noises, dragging movement, or visible flat spots/cracks on the wheel

• Disconnect power and water supply before servicing; wear appropriate gloves and eye protection
• Access the base/suspension per the service information and support the tub to remove load from the wheel
• Remove the retainer/axle, install the new wheel, and free rotation and correct orientation
• Reassemble, level the appliance, and run a spin test to check for noise and balance

Creates a leak-resistant seal between pump components and connections. Replace when you notice water leaking during drain cycles or around fittings.

This tub wheel mounts on the dishwasher's tub wall to guide and support the rack as it slides in and out. Replacing a worn wheel restores smooth rack movement and helps prevent binding, noise, and derailments.

• Mounts to the tub to provide rolling support for the dish rack/rail
• Replaces cracked, flattened, or missing wheels that impede rack travel
• Helps fix racks that stick, bind, are hard to pull/push, or derail
• Reduces grinding or squeaking from the rack area

• Disconnect power at the breaker before servicing
• Open the door and pull the rack forward for access
• Release the old wheel from its retainer/axle per your model's design; install the new wheel in the same orientation
• Ensure the wheel spins freely and the rack slides smoothly before use

Replacement tension spring for dishwasher doors and mechanisms. Restores proper return force when the original spring is broken, stretched, or missing.

Replacement leveling leg that stabilizes and adjusts your dishwasher height for proper alignment. Needed when bent, broken, or missing to eliminate rocking.

Fix loose or rattling dishwasher trim panels with this dispenser retainer clip. Secures interior panels and exterior trim for proper fit. Easy repair.

This is a handle that attaches to the silverware basket inside a dishwasher, making it easy to lift and carry the basket when loading or unloading. It snaps or clips onto the top of the basket. Replace this handle if it is cracked, broken, or missing, which makes removing the silverware basket difficult.

8-32 x 3/8" machine screw secures dishwasher control panels, brackets, and interior assemblies. Replace missing, stripped, or lost screws during repairs.

Fixes dishwasher overfilling or not filling properly. This float rises with water to signal when the tub is full. DIY-friendly repair in under 30 minutes.

This small rubber grommet seals the opening around the dishwasher's detergent/rinse-aid dispenser, helping prevent leaks and moisture intrusion so the dispenser operates reliably throughout the wash cycle.

• Seals the dispenser passage to keep water from leaking into or out of the dispenser cavity
• Helps ensure proper detergent or rinse-aid dispensing
• Can reduce moisture-related corrosion or staining in the dispenser area

• Disconnect power and turn off water before servicing
• Remove inner door panel to access the dispenser assembly
• Note grommet orientation; seat fully to ensure a watertight seal
• Inspect surrounding surfaces for debris or damage before reassembly

Clips onto the dishwasher rack rail to prevent the rack from sliding off. Replace if lost or damaged to keep racks secure. Confirm fit by model.

This switch holder secures a small appliance switch or actuator in the correct position so the control can detect and respond reliably. Replacing a cracked or broken holder restores consistent switch alignment and helps prevent intermittent operation. What it does:

• Holds the switch or actuator steady in the correct position for reliable electrical contact and activation
• Keeps the switch aligned so buttons, door/lid actions, or control functions register properly
• Common symptom: appliance function won't engage or is intermittent when the switch is loose or the holder is damaged
• Prevents further wear on the switch by keeping it from shifting or rubbing against surrounding parts

• Disconnect power (unplug or shut off breaker) before servicing the appliance
• Remove the control panel or access panel to reach the holder; keep small clips and screws organized
• Inspect the switch and actuator for damage while replacing the holder; replace any damaged mating parts