Mdb58600awb Parts

To order indicator lens use WP22001948.

Dishwasher rack rear bowl tine. For the front tine order 12002218. For the tine clip order WPY912709.

This dishwasher door strike mounts to the tub opening and provides the catch point for the door latch. Replacing a worn or bent strike restores positive latching so the control can sense a closed door and run cycles reliably.

• Provides the catch the door latch locks onto
• Engages the door switch so the dishwasher can start
• Helps keep the door securely closed during operation
• Common symptoms: door won't latch or pops open; unit won't start unless pressure is applied to the door; strike is visibly bent, worn, or missing

• Disconnect power at the breaker; turn off water if you need to move the appliance
• Open the door to access the strike at the tub opening; remove mounting screws, replace the strike, and tighten securely
• Save and reuse the original mounting screws
• After installation, check latch engagement and adjust appliance leveling or alignment if needed

This upper rack wheel and axle assembly lets your dishwasher's top rack glide smoothly and stay level. Replace a cracked or missing wheel to fix hard-to-slide racks, scraping noises, or a rack that slips off the rail.

• Provides rolling support for the upper rack along the rails
• Helps keep the rack aligned to prevent sagging or derailment
• Replaces worn, cracked, or seized wheel assemblies
• Common symptoms: rack hard to slide, wheel wobbles/missing, grinding or scraping sounds, rack coming off track

• Disconnect power to the dishwasher for safety
• Pull out the upper rack and remove the rail end caps if needed
• Release and remove the damaged wheel/axle assembly from the rack
• Snap the new assembly into place, reinstall end caps, and test rack movement

This dishwasher drain hose channels wastewater from the pump to your home drain or air gap. Replacing a cracked, kinked, or clogged hose restores proper draining performance and helps prevent leaks or water backing into the tub. What it does:

• Routes wastewater from the dishwasher to the household drain or air gap
• A damaged, kinked, or blocked hose can cause slow/no drain, standing water, or leaks
• Visible splits, soft spots, or persistent odors/backflow are common signs the hose should be replaced
• Restores reliable draining and helps protect surrounding cabinets and flooring from water damage

• 1 drain hose

• Disconnect power and shut off water before servicing
• Pull the dishwasher forward and place a towel or pan to catch residual water
• Match the original routing and maintain a proper high loop or air gap per local code to prevent backflow
• Secure connections with clamps, ensure the hose isn't kinked, and run a test cycle to check for leaks

This little door seal goes on the corner of the dishwasher door. There are two of these seals - one in each corner. It is recommended to order and replace both. If you need pushnuts, order 99002756.

Used on the ends of the tines inside the dishwasher rack.

This short connector hose links internal dishwasher plumbing to move water securely between components. Replacing a worn or cracked hose helps prevent leaks and keeps cycles running reliably. What it does:

• Routes water between two internal connection points during the wash cycle
• Helps maintain a watertight seal when properly clamped
• Common symptoms: water leaking beneath the unit, dampness around hose joints, visible cracks/hardening, or a loose fit
• Aging hoses can stiffen and drip at barbed fittings

• 1 connector hose

• Disconnect power and shut off the water supply before servicing
• Remove the toe-kick and pull the dishwasher forward as needed to access the hose
• Expect a small amount of residual water; have towels or a shallow pan ready
• Fully seat the hose on fittings, secure with appropriate clamps, then run a brief cycle and check for leaks

This door spring provides the tension that counterbalances the appliance door, allowing smooth, controlled opening and closing. Replacing a fatigued or broken spring restores proper door action and helps prevent the door from dropping or slamming. What it does:

• Provides counterbalance tension for controlled door movement
• Works with the door hinge mechanism to support door weight
• Helps the door open evenly and close with appropriate force
• Common symptoms: door falls open too quickly, feels heavy, opens unevenly, or a broken/distorted spring is visible

• 1 door spring

• Disconnect power before servicing the appliance
• Support the door and carefully relieve spring tension before removal
• Springs are under tension—use gloves and eye protection
• If your model uses two springs, replace both for balanced tension

Used on the end of the rails to prevent the upper rack from falling out.

This small rubber grommet seals the opening around the dishwasher's detergent/rinse-aid dispenser, helping prevent leaks and moisture intrusion so the dispenser operates reliably throughout the wash cycle.

• Seals the dispenser passage to keep water from leaking into or out of the dispenser cavity
• Helps ensure proper detergent or rinse-aid dispensing
• Can reduce moisture-related corrosion or staining in the dispenser area

• Disconnect power and turn off water before servicing
• Remove inner door panel to access the dispenser assembly
• Note grommet orientation; seat fully to ensure a watertight seal
• Inspect surrounding surfaces for debris or damage before reassembly

This O-ring seal fits into a groove to create a tight, leak-resistant barrier where two parts join. Replacing a worn O-ring helps stop drips at connections and keeps your appliance running reliably. What it does:

• Forms a compressible seal between mating parts (fittings, housings, or tubing)
• Helps prevent water or fluid leaks at joints
• Maintains proper pressure and flow within the sealed path
• Replace if you see seepage at the connection or the ring is cracked, flattened, brittle, or swollen

• 1 O-ring seal

• Disconnect power and shut off water supply before servicing
• Clean the groove and mating surfaces; remove debris that could compromise the seal
• Lightly lubricate with manufacturer-approved silicone grease; avoid petroleum-based products
• Seat the O-ring without twisting; reassemble carefully and check for leaks after testing

This top wash arm retainer secures the dishwasher's upper spray arm so it spins freely and stays aligned, helping maintain proper water distribution for upper-rack cleaning. Replace a cracked or worn retainer to reduce wobble and misalignment. What it does:

• Holds the upper/ top spray arm in place on the spray assembly so the arm can rotate correctly.
• Prevents the spray arm from slipping or wobbling during the wash cycle.
• Helps restore proper water spray coverage to the upper rack when the original retainer is broken or worn.
• Compatible with standard upper spray arm mounting—no modification required.

• Includes: 1 top wash arm retainer

• Disconnect power to the appliance before beginning any repair.
• You may need to remove the upper rack and/or the spray arm to access the retainer; keep parts organized for reassembly.
• Inspect the spray arm and attachment for damage or debris while replacing the retainer.
• Use hand tools only.

The Tub Wheel supports and guides the washer's tub assembly on its base during wash and spin cycles. Replacing a worn wheel restores smoother, quieter operation and helps reduce vibration and rubbing as the machine operates.

• Provides rolling support so the tub can move and self-balance during cycles
• Reduces friction between the tub and the base/frame
• Helps keep the tub centered to minimize noise and vibration
• Failure symptoms include squeaking or grinding, scraping noises, dragging movement, or visible flat spots/cracks on the wheel

• Disconnect power and water supply before servicing; wear appropriate gloves and eye protection
• Access the base/suspension per the service information and support the tub to remove load from the wheel
• Remove the retainer/axle, install the new wheel, and free rotation and correct orientation
• Reassemble, level the appliance, and run a spin test to check for noise and balance

Black

Screw: 8-16 x 3/8 inch.