Med400vw0 Parts

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This strike is the latch receiver the door or lid engages when closed. Replacing a worn or broken strike restores a secure close and ensures the control correctly senses a closed door so cycles can run. What it does:

• Provides the fixed catch point for the latch mechanism
• Keeps the door/lid closed and properly aligned during operation
• Works with the interlock/switch to signal that the door/lid is closed
• Common symptoms: door won't latch or pops open, "door/lid open" message, cycle won't start, visible damage to the strike

• 1 strike

• Disconnect electrical power to the appliance; shut off water if applicable
• Open the door/lid and remove the original strike (typically secured by screws or retaining tabs)
• Position and secure the new strike, reusing original hardware; tighten snugly without over-tightening
• Close and open the door/lid to confirm smooth latch engagement and alignment; adjust if needed

This Heater Box Bracket secures the dryer's heater housing to the cabinet, keeping the heating assembly firmly mounted and aligned. Replace a bent, cracked, or missing bracket to restore stable support and reduce vibration around the heater area.

• Anchors the heater housing/box to the cabinet frame
• Maintains proper alignment and clearance for the heating element assembly
• Helps prevent rattling or rubbing noises from a loose heater housing
• A damaged bracket may leave the heater housing loose, cause vibration, or contribute to intermittent heating issues

• Disconnect power; if gas, shut off gas supply and allow the unit to cool completely
• Access the heater housing; note bracket orientation and reuse existing fasteners
• Support the heater housing and keep wiring clear while removing/installing the bracket
• After installation, verify the housing sits square and clear of the drum and wiring before restoring power

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Replacement bumper that cushions appliance parts and absorbs shock to prevent rubbing, rattling and surface damage. Restores proper fit and quieter operation for components that contact cabinets, doors or panels. What it does:

• Cushions contact points to reduce noise from doors, drawers or panels.
• Prevents metal-to-metal or metal-to-surface scraping that can cause wear or cosmetic damage.
• Helps components close and seat more evenly to reduce vibration and movement.
• Common symptom fixes: eliminates rattling, stops rubbing noises, and prevents chipping or scuffing where parts meet.

• One bumper.

• High-level, tool-light replacement; usually presses into or adheres to the mounting surface.
• Disconnect power or unplug the appliance before opening panels where required.
• Inspect surrounding clips/retainers and clean the mounting area for best adhesion or fit.

This socket is an electrical connector that secures a wiring plug to an appliance component, restoring reliable contact and reducing intermittent power or component failures caused by a worn or damaged connector. What it does:

• Provides a stable electrical connection between wiring and the appliance component.
• Ensures consistent power transfer to control boards, motors or heating elements.
• A faulty socket can cause intermittent operation, loss of function, arcing, or a component that does not receive power.
• Replacing a corroded or loose socket can eliminate connection-related faults without replacing the whole assembly.

• Always disconnect power (and gas where applicable) before attempting any repair.
• Take a photo or label wires before removing the old socket to ensure correct reassembly.
• Replace only with the exact part; do not force connectors—ensure proper seating and secure fasteners.
• If you see damaged wiring, melted insulation, or signs of arcing, inspect and repair wiring harness.

This exhaust cover plate protects and finishes the dryer's exhaust outlet, helping direct airflow and keeping the vent opening sealed from debris. It provides a clean, durable surface where the exhaust connects to the dryer cabinet. What it does:

• Covers and seals the dryer exhaust opening to prevent dust and lint buildup around the vent
• Helps direct exhaust airflow into the duct for proper ventilation
• Restores a finished appearance to the exhaust area after repair or replacement
• Can reduce drafts and discourage pests entering through the vent opening

• Disconnect power to the appliance before starting any work.
• Use basic hand tools; handle edges carefully to avoid cuts.
• Verify proper alignment with the exhaust opening and secure with the original screws or hardware.
• Inspect the exhaust duct and surrounding seals for wear.

This blower housing assembly replaces the blower chamber that supports the blower wheel and routes air through the dryer for proper tumbling and drying. Restores correct airflow and helps reduce overheating or poor drying performance. What it does:

• Houses and supports the blower wheel to direct airflow from the drum to the exhaust.
• Ensures proper airflow for consistent drying and venting.
• Can address symptoms like weak airflow, long dry times, or unusual blower noise when damaged or cracked.
• Works with the blower wheel and motor to maintain lint passage and exhaust flow.

• Disconnect power before inspecting or replacing the blower housing; follow manufacturer safety procedures.
• Access may require removing the dryer front or rear panel depending on model.
• Inspect the blower wheel and motor for damage or obstructions while replacing the housing.

The Wire Harness is an OEM part for Whirlpool dryers. This wire harness is responsible for delivering power and electricity throughout the dryer and to its individual components. 

Causes of a bad wire harness can include fraying or exposed wires due to wear and tear over time, cracking or damage of protective casings that expose internal wirings, or malfunctioning connections that disrupt power flow.

Symptoms of a bad wire harness include:

• The dryer not starting or powering on
• Components like the drum or heating elements not working
• Buzzing or humming noises coming from inside the dryer
• Tripped or blown fuses
• Error codes or failure to progress through cycles properly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: White

This lint duct assembly channels dryer exhaust through the cabinet and toward the vent, helping trap lint and maintain airflow for efficient drying. Replace a damaged or clogged duct to restore proper venting and reduce lint buildup. What it does:

• Directs exhaust air from the drum to the vent path to support consistent drying performance
• Helps contain and route lint toward the lint trap area to reduce internal buildup
• Common part for symptoms like poor drying, overheating, unusual airflow, or visible lint leaks inside the cabinet
• Works with the dryer cabinet and venting components to maintain safe exhaust flow

• One lint duct assembly

• Disconnect power (and gas supply, if applicable) before service to avoid shock or injury
• Inspect surrounding seals, gaskets and the lint trap for damage during replacement
• Reinstall using OEM fasteners and confirm proper alignment to prevent exhaust leaks

This 6-foot, 4-prong range power cord provides a dedicated 240V connection for electric ranges and stoves, replacing worn or damaged cords to restore reliable power and reduce risk of arcing or intermittent operation. What it does

• Supplies 240V/30A power to the range via a 4-wire (hot/hot/neutral/ground) connection
• Replaces cords with frayed insulation, exposed conductors, or melted ends
• Stops symptoms such as no power to the range, tripping breakers, or intermittent heating
• Ensures a grounded connection when installed correctly

• One 6 ft, 4-prong (30 amp) range power cord, bagged

• Always disconnect household power at the breaker before starting work
• Use the existing strain relief or mounting bracket to secure the cord and prevent tugging

The Seal is an OEM replacement part for Whirlpool dryers. It creates a tight seal between the dryer door and the drum, preventing heat and moisture from escaping during the drying process. It helps maintain the proper temperature inside the dryer, allowing your clothes to dry quickly and evenly.

Symptoms of a faulty door seal include:

• Heat escaping from around the dryer door
• Excessive moisture or lint buildup
• Extended drying times

A bad door seal can occur due to regular use, wear and tear, or accidental damage. If you notice issues such as heat escaping from around the dryer door, excessive moisture or lint buildup, or clothes taking longer to dry than usual, it may be time to replace the door seal.

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This seal creates a tight barrier between two mating surfaces in your appliance, helping prevent leaks and performance loss. Replacing a worn seal restores proper containment and helps protect nearby components from moisture intrusion. What it does

• Forms a tight barrier to prevent water or air from escaping between joined parts
• Helps maintain proper pressure, airflow, or water path as designed
• Replaces cracked, flattened, or torn seals that compromise performance
• Common symptoms: drips or moisture at the joint, visible wear or deformation, loose fit, recurring leaks after reassembly

• 1 seal

• Disconnect power and, shut off the water supply before servicing
• Note the seal's orientation and match the new part to the old one
• Clean and dry mating surfaces; remove old adhesive, debris, or scale
• Install per OEM orientation; only lubricate if specified by the manufacturer, then reassemble and test for leaks