Med7900sq Parts

This push-button switch is the control-panel user-input switch that restores button responsiveness and reliable selection input. Replace a broken, stuck, or intermittently working button to regain normal front-panel control. What it does:

• Acts as the momentary push-button contact for the appliance control console.
• Replaces buttons that are physically cracked, stuck, or that fail to register presses.
• Helps stop intermittent or no-response conditions caused by worn or disconnected switches.
• Restores normal tactile feedback and electrical contact when the button is pressed.

• Disconnect power (unplug appliance or turn off circuit breaker) before attempting any repair.
• Access the control panel per your model's service instructions; handle sharp edges and fasteners carefully.
• Note wire connector orientation and secure all electrical connections before reassembly.
• Test the switch operation after reconnecting power and before completing reassembly.

This elbow redirects a fluid or air line inside the appliance to allow routing around components and tight spaces. It restores proper flow path and helps stop leaks or blockages when the original elbow is cracked or worn. What it does:

• Provides a sealed change of direction for a water, drain, or vent line inside the appliance
• Replaces a cracked or broken elbow that can cause leaks, water pooling, or reduced flow
• Re-establishes the correct routing to prevent kinks and stress on connected hoses or tubing
• Helps eliminate intermittent draining or venting issues caused by a damaged fitting

• Disconnect power and shut off water supply before accessing the part
• Verify orientation and routing before removing the old elbow to ensure correct reinstallation
• Inspect and replace any worn clamps, gaskets, or hoses when installing the new elbow
• Tighten fittings to secure but avoid over-tightening which can crack plastic components

Fix a dryer that won't start or hums but doesn't spin. This motor run/start capacitor restores reliable motor operation. DIY-friendly repair in under an hour.

Replacement mounting screw for securing panels, brackets, and components to your appliance chassis. Needed when original screws are stripped or missing.

This is a replacement door handle for a dryer, used to open and close the dryer door. It attaches directly to the door panel and provides a secure grip for daily use. Replace this handle if it is cracked, broken, or loose, making it difficult to open or properly latch the dryer door.

Dryer won't heat or overheats? This thermostat regulates temperature during drying cycles. Easy 15-minute DIY fix restores proper heat control.

This Y-shaped connector hose diverts water between two inlet lines to route supply where needed. It restores proper water flow paths and replaces damaged or leaking split-connection plumbing on compatible appliances. What it does:

• Splits a single water inlet into two outlets so water can serve two components
• Provides a sealed path to prevent cross-flow between lines
• Commonly replaced when the connector leaks, cracks, or becomes brittle
• Helps restore normal water delivery when a split supply is required

• Turn off the appliance and shut off the water supply before beginning.
• Inspect mating fittings and replace any damaged clamps or seals.
• Hand-start fittings to avoid cross-threading, then tighten securely; check manufacturer torque guidance if available.
• After installation, restore water and power and check all connections carefully for leaks.

Color: White. Size: 1 qt. can. Acrylic appliance paint.

Dryer lint screen catches fibers during drying cycles. Replace when torn, clogged, or damaged to maintain airflow and efficiency. Verify fit with your model.

Support plate mounts inside your dryer to secure internal components. Replace if the plate is cracked, bent, broken, or missing to restore proper assembly.

Replacement housing cover for your dryer's control panel. Installs on the top front of the unit. Order a new one if yours is cracked or broken.

This kit includes the components needed to reverse the swing direction of the dryer door from one side to the other. It is useful when repositioning the dryer in a new location where the current door swing is inconvenient. The kit typically includes the door, hinge hardware, and any necessary trim pieces for a complete reversal.